Morphology characteristics of macrostructure in 82B steel billet based on high throughput experimental principle
PENG Zhi-qiang1,2, CAO Jiang-hai1,2, HOU Zi-bing1,2
1. College of Materials Science and Engineering, Chongqing University, Chongqing 400044, China; 2. Chongqing Key Laboratory of Vanadium-Titanium Metallurgy and New Materials, Chongqing University, Chongqing 400044, China
Abstract：The morphology of the solidification structure has a very important influence on the formation of macrosegregation in billet and determines its subsequent processing performance to some extent. This paper introduces the fractal dimension and dimensionless perimeter to analyze the morphology characteristics of solidification structure in billet of 82B cord steel based on the principle of high throughput experiment. The results show that for the middle zone on both sides of the continuous casting billet,the area ratio of solidification structure obtained by the narrow-width and long-region sampling method can be approximately equivalent to the solid fraction. Meanwhile,the fractal dimension of the overall morphology of the solidification structure increases with the solid fraction,but its dimensionless perimeter shows the opposite trend,so the two have opposite effects on the permeability of the solidification structure. And the calculation shows that the solid fraction corresponding to the minimum permeability of the solidification structure in the actual billet is 0.667. A new method for analyzing the evolution law of solidification structure based on actual casting billet is proposed,which can also provide a reference for the best action area of segregation control technology such as final electromagnetic stirring and soft reduction in continuous casting.
彭治强, 曹江海, 侯自兵. 基于高通量试验原理82B连铸坯组织形貌特征[J]. 钢铁, 2021, 56(7): 86-93.
PENG Zhi-qiang, CAO Jiang-hai, HOU Zi-bing. Morphology characteristics of macrostructure in 82B steel billet based on high throughput experimental principle[J]. Iron and Steel, 2021, 56(7): 86-93.
[1] 胡亮,郭红民,段少平. 凝固末端电磁搅拌对82B碳偏析的影响[J]. 中国冶金,2018,28(9):63.(HU Liang,GUO Hong-min,DUAN Shao-ping. Effect of F-EMS on carbon segregation of 82B[J]. China Metallurgy,2018,28(9):63.) [2] 郭洛方,惠荣,王广顺,等. 高碳钢凸辊轻压下工艺模型研究与应用[J]. 连铸,2021,46(1):36.(GUO Luo-fang,HUI Rong,WANG Guang-shun,et al. Study and application on soft reduction operation models of convex roller for high carbon steel[J]. Continuous Casting,2021,46(1):36.) [3] 曾杰,张森林,刘澄,等. 高碳钢矩形坯凝固末端永磁搅拌试验[J]. 钢铁,2016,51(7):22.(ZENG Jie,ZHANG Sen-lin,LIU Cheng,et al. Final permanent magnet stirring in high carbon rectangular billet continuous casting[J]. Iron and Steel,2016,51(7):22.) [4] Natsume Y,Takahashi D,Kawashima K. Evaluation of permeability for columnar dendritic structures by three dimensional numerical flow analysis[J]. Tetsu to Hagane,2013,99(2):117. [5] LI B,Brody H D,Kazimirov A. Real time synchrotron microradiography of dendrite coarsening in Sn-13 wt pct Bi alloy[J]. Metallurgical and Materials Transactions A,2007,38(3):599. [6] 林寒,岳峰,吴华杰,等. 对20CrMnTi钢凝固组织影响的模拟[J]. 钢铁,2016,51(11):36.(LIN Han,YUE Feng,WU Hua-jie,et al. Numerical simulation of effects of alloying elements on solidification structure of 20CrMnTi billets[J]. Iron and Steel,2016,51(11):36.) [7] 汪洪,向勇,项晓东,等. 材料基因组——材料研发新模式[J]. 科技导报,2015,33(10):13.(WANG Hong,XIANG Yong,XIANG Xiao-dong,et al. Materials genome enables research and development revolution[J]. Science and Technology Review,2015,33(10):13.) [8] 关洪达,李才巨,高鹏,等. 材料高通量制备与表征技术研究进展[J]. 稀有金属材料与工程,2019,48(12):4131.(GUAN Hong-da,LI Cai-ju,GAO Peng,et al. Research progress of high-throughput material synthesis and characterization[J]. Rare Metal Materials and Engineering,2019,48(12):4131.) [9] Zhong X T,Rowenhorst D J,Beladi H,et al. The five-parameter grain boundary curvature distribution in an austenitic and ferritic steel[J]. Acta Mater,2017,123(1):136. [10] Ohsasa K,Natsume Y,Sekiya T,et al. Evaluation of dendrite morphology using fractal dimension and dimensionless perimeter in unidirectionally solidified Al-Si alloys[J]. IOP Conference Series Materials Science and Engineering,2015,84(1):012033. [11] WANG W,HOU Z B,CHANG Y,et al. Effect of superheat on quality of central equiaxed grain zone of continuously cast bearing steel billet based on two-dimensional segregation ratio[J]. Journal of Iron and Steel Research, International,2018,25(1):1. [12] Flemings M C,Kattamis T Z,Bardes B P. Dendrite arm spacing in aluminum alloys[J]. Trans Am Foundry Soc,1991,89:501. [13] Jacobi H,Schwerdtfeger K. Dendrite morphology of steady state unidirectionally solidified steel[J]. Metallurgical Transactions A,1976,7(6):811. [14] 李立新,黄英钢,张葵,等. 轧辊磨损过程中的形貌图像特征及分形[J]. 钢铁,2015,50(4):95.(LI Li-xin,HUANG Ying-gang,ZHANG Kui,et al. Image feature and fractal on roll surface morphology in wear process[J]. Iron and Steel,2015,50(4):95.) [15] 侯自兵,曹江海,常毅,等. 基于分形维数的模具钢电渣重熔铸坯碳偏析形貌特征研究[J]. 金属学报,2017,53(7):769.(HOU Zi-bing,CAO Jiang-hai,CHANG Yi,et al. Morphology characteristics of carbon segregation in die steel billet by ESR based on fractal dimension[J]. Acta Metallurgica Sinica,2017,53(7):769.) [16] XU J J,WANG T M,ZHU J,et al. In situ study on secondary dendrite arm coarsening of Sn-Bi alloy by synchrotron microradiography[J]. Materials Research Innovations,2011,15(2):156. [17] ZHAO Jing,ZHONG Hong-gang,HAN Ke,et al. Relationship between secondary dendrite arm spacing and local solidification time of 30Cr2 Ni4MoV alloy at slow cooling rates[J]. Journal of Iron and Steel Research International,2018,25(8):821. [18] Nakano K,Narumi T,Morishita K,et al. Characterization of growing dendrites in CrMnFeCoNi high entropy alloy by time-resolved and in-situ tomography[J]. Materials Transactions,2020,61(4):596. [19] Tiller W A,Jackson K A,Rutter J W,et al. The redistribution of solute atoms during the solidification of metals[J]. Acta Metallurgica,1953,1(4):428. [20] Eiichi Aritaka,Hisao Esaka,Kei Shinozuka. Mechanism for complex morphology due to mechanical vibration[J]. ISIJ International,2016,56(8):1413. [21] 朱鸣芳,邢丽科,方辉,等. 合金凝固枝晶粗化的研究进展[J]. 金属学报,2018,54(5):180.(ZHU Ming-fang,XING Li-ke,FANG Hui,et al. Progresses in dendrite coarsening during solidification of alloys[J]. Acta Metallurgica Sinica,2018,54(5):180.) [22] Ratke L,Genau A. Evolution of specific surface area with solid fraction during solidification[J]. Acta Materialia,2010,58(12):4207. [23] Natsume Y,Takahashi D,Kawashima K,et al. Quantitative model to determine permeability for columnar dendritic structures[J]. ISIJ International,2013,53(5):838. [24] 胡汉起. 金属凝固原理[M]. 2版. 北京:机械工业出版社,2010.(HU Han-qi. Principle of Metal Solidification[M]. 2nd ed. Beijing:Mechanical Industry Press,2010.) [25] Carman P C. Flow of Gases Through Porous Media[M]. London:Butterworth Scientific Publications,1956. [26] Ishida H,Natsume Y,Ohsasa K. Characterization of dendrite morphology for evaluating interdendritic fluidity based on phase-field simulation[J]. ISIJ International,2009,49(1):37. [27] Kyung Shik Oh,Young Won Chang. Macrosegregation behavior in continuously cast high carbon steel blooms and billets at the final stage of solidification in combination stirring[J]. ISIJ International,1995,35(7):866.
2021, Vol. 56 
