齿轮钢高温渗碳后的疲劳性能

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (0 KB) HTML (0 KB)
输出: BibTeX | EndNote (RIS)

摘要利用旋转弯曲疲劳试验方法，研究了Nb和Ti微合金化20CrMn齿轮钢（20CrMnNb钢：w(Nb)0.077%；20CrMnTiNb钢：w(Nb)0.048%+w(Ti)0.038%）经1000℃高温渗碳后的疲劳性能。结果表明，Nb-Ti复合微合金化的20CrMnTiNb钢中析出相尺寸小、数量多，其渗碳层原奥氏体晶粒平均尺寸明显低于Nb微合金化的20CrMnNb钢，因而20CrMnTiNb钢的疲劳极限高于20CrMnNb钢。疲劳断口观察发现，20CrMnNb和20CrMnTiNb钢主要以近表面基体方式起裂，渗碳层中疲劳裂纹沿晶界扩展，因而晶粒尺寸较细的20CrMnTiNb钢的疲劳性能较高。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	杨延辉
	王毛球
	陈敬超
	董瀚

关键词 ：齿轮钢, 高温渗碳, 微合金化, 析出相, 疲劳性能

Abstract：The fatigue properties of microalloying gear steels with Nb and Ti (steel A1:w(Nb)0.077%; steel A2:w(Nb)0048%+w(Ti)0.038%) after carburized at 1000℃ were investigated by means of rotating bending fatigue tests. The results show that the precipitates in steel A2 microalloyed with Nb and Ti are smaller in size and higher in volume fraction than those in steel A1 microalloyed only with Nb resulting in the higher fatigue limit for steel A2 compared with steel A1. The SEM observation of fracture surface show that the fatigue crack initiates from the near surface matrix for both steels, and it propagates around grain boundaries in the carburized case, and thus superior fatigue properties are found for steel A2 with finer and more uniform prior austenite grains in carburized case layers.

收稿日期: 2012-09-04 出版日期: 2013-07-18

引用本文:

杨延辉，王毛球，陈敬超，董瀚. 齿轮钢高温渗碳后的疲劳性能[J]. 钢铁, 2013, 48(7): 53-57. YANG Yan-hui,,WANG Mao-qiu,CHEN Jing-chao,DONG Han. Fatigue Properties of Gear Steels After High Temperature Carburizing. Iron and Steel, 2013, 48(7): 53-57.

链接本文:

http://www.chinamet.cn/Jweb_gt/CN/ 或 http://www.chinamet.cn/Jweb_gt/CN/Y2013/V48/I7/53

[1]	Goldstein J I,Moren A E. Diffusion modeling of the carburization process[J]. Metall Trans A, 1978, 9(11): 1515-1525
[1]	Goldstein J I,Moren A E. Diffusion modeling of the carburization process[J]. Metall Trans A, 1978, 9(11): 1515-1525
[2]	马莉,王毛球,董瀚. 铌硼微合金化齿轮钢的晶粒尺寸及淬透性[J]. 材料热处理学报, 2009, 30(5): 74-78
[2]	马莉,王毛球,董瀚. 铌硼微合金化齿轮钢的晶粒尺寸及淬透性[J]. 材料热处理学报, 2009, 30(5): 74-78
[3]	刘燕,王毛球,董瀚. 含铌齿轮钢的晶粒长大动力学[J]. 钢铁研究学报, 2008, 20(11): 37-42
[3]	刘燕,王毛球,董瀚. 含铌齿轮钢的晶粒长大动力学[J]. 钢铁研究学报, 2008, 20(11): 37-42
[4]	马莉,王毛球,董瀚. 微合金化渗碳齿轮钢的研究进展[J]. 特殊钢,2008, 29(4): 28-30
[4]	马莉,王毛球,董瀚. 微合金化渗碳齿轮钢的研究进展[J]. 特殊钢,2008, 29(4): 28-30
[5]	Thompson R E, Matlock D K, Speer J G. The Fatigue Performance of High Temperature Vacuum Carburized Nb Modified 8620 Steel. SAE World Congress and Exhibition, April 2007(Detroit,MI,USA),p 2007-01-100
[5]	Thompson R E, Matlock D K, Speer J G. The Fatigue Performance of High Temperature Vacuum Carburized Nb Modified 8620 Steel. SAE World Congress and Exhibition, April 2007(Detroit,MI,USA),p 2007-01-100
[6]	雍启龙.钢铁材料中的第二相[M]. 北京：冶金工业出版社.2000
[6]	雍启龙.钢铁材料中的第二相[M]. 北京：冶金工业出版社.2000
[7]	David K, Khaled A, Mark D,et al. Surface Processing to Improve The Fatigue Resistance of Advanced Bar Steels for Automotive Applications[J]. Materials Research, 2005, 8(4): 453-459
[7]	David K, Khaled A, Mark D,et al. Surface Processing to Improve The Fatigue Resistance of Advanced Bar Steels for Automotive Applications[J]. Materials Research, 2005, 8(4): 453-459
[8]	王彦彬,王毛球,黎振华,等.晶粒尺寸对表面渗碳钢疲劳极限的影响[J],钢铁研究学报,2010,22(11): 23-2
[8]	王彦彬,王毛球,黎振华,等.晶粒尺寸对表面渗碳钢疲劳极限的影响[J],钢铁研究学报,2010,22(11): 23-2
[9]	Liu Yan,Wang Maoqiu,Shi Jie,et al. Fatigue properties of two case hardening steels after carburization[J]. International Journal of Fatigue, 2009, 31: 292-29
[9]	Liu Yan,Wang Maoqiu,Shi Jie,et al. Fatigue properties of two case hardening steels after carburization[J]. International Journal of Fatigue, 2009, 31: 292-29
[10]	Ma Li,Wang Maoqiu,Shi Jie,et al.Influence of niobium microalloying on rotating bending fatigue properties of case carburized steels[J]. Materials Science and Engineering A, 2008,498(1-2): 258-26
[10]	Ma Li,Wang Maoqiu,Shi Jie,et al.Influence of niobium microalloying on rotating bending fatigue properties of case carburized steels[J]. Materials Science and Engineering A, 2008,498(1-2): 258-26
[11]	越智達朗,久保田学,等.浸炭材の疲労き裂の伝ぽ特性?停留特性に及ぼすγ粒径効果[J]. 鉄と鋼,2011, 97(11): 52-56
[11]	越智達朗,久保田学,等.浸炭材の疲労き裂の伝ぽ特性?停留特性に及ぼすγ粒径効果[J]. 鉄と鋼,2011, 97(11): 52-56