Heat Transfer on Masonry Structure of Hearth Carbon Bricks
LI Yang-long1,2,3,CHENG Shu-sen1,2,3
(1. School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing,Beijing 100083, China 2. Beijing Key Labortory of Green Recycling and Extraction of Metal GREM, Beijing 100083, China 3. State Key Laboratory of Advanced Metallurgy, Beijing 100083, China)
Abstract:The mathematical models of blast furnace (BF) hearth were established and the masonry structures of large carbon blocks and small carbon bricks for hearth were discussed from the view of heat transfer.The temperature of these two hearth structures during BF drying process were calculated as well as after blow-in.It is found that the filling between staves and carbon bricks can not be dried effectively at present BF drying conditions and the thermal conductivity of filling can not reach the designed value.Moreover,with the existing of filling,the hot face temperature of lining is higher which results in more serious erosion.Therefore,the filling should be cancelled between staves and carbon bricks.It has obvious advantage of heat transfer for carbon bricks touching with staves directly.The hearth structure of small carbon bricks could be designed to touch with staves directly so that it exterminates the barriers on heat transfer of hearth.The hearth structure of large carbon blocks should be put some small carbon bricks touch with staves directly and then make the filling between the small carbon bricks and large carbon blocks.The filling moves towards center of BF more than about 200mm.In order to dry filling completely during BF drying process,the necessary method is without utilizing cooling water.Meanwhile,some measures are discussed for keep staves safe.
李洋龙,, 程树森,. 高炉炉缸炭砖砌筑结构的传热学[J]. 钢铁, 2014, 49(5): 13-18.
LI Yang-long,,,CHENG Shu-sen,,. Heat Transfer on Masonry Structure of Hearth Carbon Bricks. Iron and Steel, 2014, 49(5): 13-18.
Wang G X, Yu A B, Zulli P. Three-dimension Modeling of the wall heat transfer in the lower stack region of a blast furnace. ISIJ int., 1997, 37(5): 441.
[3]
Wang G X, Yu A B, Zulli P. Three-dimension Modeling of the wall heat transfer in the lower stack region of a blast furnace. ISIJ int., 1997, 37(5): 441.
[4]
Inada T, Takata K, Takatani K, et al. Effect of blast furnace profile on inner furnace states. ISIJ int., 2003, 43(7): 1003.
[4]
Inada T, Takata K, Takatani K, et al. Effect of blast furnace profile on inner furnace states. ISIJ int., 2003, 43(7): 1003.
[5]
Torrkulla J, Saxen H. Model of the state of the blast furnace hearth. ISIJ int., 2000,40(5): 438.
[5]
Torrkulla J, Saxen H. Model of the state of the blast furnace hearth. ISIJ int., 2000,40(5): 438.
[6]
Torrkulla J, Brannbacka J, Saxen H, et al. Indicators of the Internal State of the Blast Furnace Hearth. ISIJ int., 2002,42(5): 504.
[6]
Torrkulla J, Brannbacka J, Saxen H, et al. Indicators of the Internal State of the Blast Furnace Hearth. ISIJ int., 2002,42(5): 504.
[7]
Shinotake A, Nakamubr H, Yadoumaru N, et al. Investigation of blast-furnace hearth sidewall erosion by core sample analysis and consideration of campaign operation. ISIJ int., 2003, 43 (3): 321.
[7]
Shinotake A, Nakamubr H, Yadoumaru N, et al. Investigation of blast-furnace hearth sidewall erosion by core sample analysis and consideration of campaign operation. ISIJ int., 2003, 43 (3): 321.
[8]
Takatani K, Inada T, Takata K. Mathematical model for transient erosion process of blast furnace hearth. ISIJ int., 2001, 41(10):1139.
[8]
Takatani K, Inada T, Takata K. Mathematical model for transient erosion process of blast furnace hearth. ISIJ int., 2001, 41(10):1139.
[9]
Preuer A, Winter J and Hiebler H. Computation of erosion in the hearth of a blast furnace. Steel Research, 1992, 63(4):147.
[9]
Preuer A, Winter J and Hiebler H. Computation of erosion in the hearth of a blast furnace. Steel Research, 1992, 63(4):147.
[10]
Jung J S, Kim S M. Estimation model of the hearth refractory thickness and its application to the operation. Steel Research, 2001, 4(72): 125.
[10]
Jung J S, Kim S M. Estimation model of the hearth refractory thickness and its application to the operation. Steel Research, 2001, 4(72): 125.
[11]
Laar R V, Callenfels ES V, Geerdes M. Blast furnace hearth management for safe and long campaigns. Iron and Steel Maker, 2003, (8): 123.
[11]
Laar R V, Callenfels ES V, Geerdes M. Blast furnace hearth management for safe and long campaigns. Iron and Steel Maker, 2003, (8): 123.