T型结晶器抽锭电渣重熔高速钢90 mm方锭新工艺

doi:10.13228/j.boyuan.issn0449-749x.20150069

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (0 KB) HTML (0 KB)
输出: BibTeX | EndNote (RIS)

摘要晶界处碳化物严重影响高速工模具钢的红硬性和耐磨性能，电渣重熔工艺能够有效地改善钢锭中碳化物尺寸及分布。传统电渣重熔生产较小钢锭的截面尺寸约为[?]200 mm，减小钢锭截面尺寸和增大冷却速率将会进一步减轻碳化物的偏析程度，但将降低生产效率、提高生产成本。采用双极串联、T型结晶器、抽锭电渣重熔新工艺生产90 mm方锭，并与相同熔化速度传统电渣重熔生产[?]200 mm钢锭进行对比试验。对钢锭成分、低倍、夹杂物、显微组织进行检验分析结果表明，90 mm方钢锭中碳化物尺寸和分布明显优于[?]200 mm钢锭，碳化物在后序锻造或轧制过程中更容易被破碎。新工艺电耗也低于传统电渣重熔工艺。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	臧喜民
	邓鑫
	姜周华
	邱天禹
	李春旭

关键词 ：抽锭电渣重熔, T型结晶器, 双极串联, 高速钢, 碳化物

Abstract：Carbide segregation at grain boundary is a main reason to reduce high temperature hardness and wear resistance of high speed steel. Electroslag remelting（ESR） technology can effectively improve the distribution and size of carbides in ingot solidification process. The ingot diameter is usually [?]200 mm by traditional ESR，but there are still a large amount of reticulated carbides. The carbide segregation degree can be reduced by further decreasing the size of ingot and increasing the cooling rate. However，it will reduce the production efficiency and increase the cost of production. Therefore，new technology on 90 mm billets by electroslag remelting withdrawing（RESW） with bifilar mode and T-mold was developed. The results indicate that macroscopic organization and the size of grain and carbides of 90 mm billets are better than the [?]200 mm ingot produced by traditional ESR technology. Reticulated carbides in 90 mm billets are easier to be broken into small particles in the sequence forging or rolling process. With same production efficiency，the cost is reduced.

收稿日期: 2015-02-09 出版日期: 2016-01-06

引用本文:

臧喜民，邓鑫，姜周华，邱天禹，李春旭. T型结晶器抽锭电渣重熔高速钢90 mm方锭新工艺[J]. 钢铁, 2016, 51(1): 39-45. ZANG Xi-min，DENG Xin，JIANG Zhou-hua，，QIU Tian-yu，LI Chun-xu. New manufacture of high speed steel 90 mm billets by electroslag remelting withdrawing process. Iron and Steel, 2016, 51(1): 39-45.

链接本文:

http://www.chinamet.cn/Jweb_gt/CN/10.13228/j.boyuan.issn0449-749x.20150069 或 http://www.chinamet.cn/Jweb_gt/CN/Y2016/V51/I1/39

[1]	李正邦.中国高速钢发展战略分析[J].钢铁, 2005, 40(1):1-7
[1]	李正邦.中国高速钢发展战略分析[J].钢铁, 2005, 40(1):1-7
[2]	YANG Jun, ZOU De ning, LI Xiao ming, DU Zhong ze.Effect of rare earth on microstructures and properties of high speed steel with high carbon content[J].Journal of Iron and Steel Research, International, 2007, 14(1):42-47
[2]	YANG Jun, ZOU De ning, LI Xiao ming, DU Zhong ze.Effect of rare earth on microstructures and properties of high speed steel with high carbon content[J].Journal of Iron and Steel Research, International, 2007, 14(1):42-47
[3]	ZHOU Li, SUN Da le, LIU Chang sheng, WU Qiong.Fatigue behavior of high speed steel roll materials for hot rolling by laser impacting[J].Journal of Iron and Steel Research, International, 2006, 13(6):49-54
[3]	ZHOU Li, SUN Da le, LIU Chang sheng, WU Qiong.Fatigue behavior of high speed steel roll materials for hot rolling by laser impacting[J].Journal of Iron and Steel Research, International, 2006, 13(6):49-54
[4]	Trabadelo V, Giménez S, Iturriza I.Microstructural characterization of vacuum sintered T42 powder metallurgy high-speed steel after heat treatments[J].Materials Science and Engineering, 2009, 499(1):360-364
[4]	Trabadelo V, Giménez S, Iturriza I.Microstructural characterization of vacuum sintered T42 powder metallurgy high-speed steel after heat treatments[J].Materials Science and Engineering, 2009, 499(1):360-364
[5]	XU Da, YU Feng, LUO Di.Factors affecting toughness of high speed steels[J].Journal of Iron and Steel Research, International, 2006, 18(11):1-6
[5]	XU Da, YU Feng, LUO Di.Factors affecting toughness of high speed steels[J].Journal of Iron and Steel Research, International, 2006, 18(11):1-6
[6]	Javaid, J. Thomson, and K.G. Davis. Critical conditions for obtaining carbide-free microstructures in thin-wall ductile irons[J].Transactions of the American Foundry Society, 2002, 110:889-898
[6]	Javaid, J. Thomson, and K.G. Davis. Critical conditions for obtaining carbide-free microstructures in thin-wall ductile irons[J].Transactions of the American Foundry Society, 2002, 110:889-898
[7]	Fredriksson H, Brising S.The formation of carbides during solidification of high speed steels[J].Scandinavian Journal of Metallurgy, 1976, 5(6):268-275
[7]	Fredriksson H, Brising S.The formation of carbides during solidification of high speed steels[J].Scandinavian Journal of Metallurgy, 1976, 5(6):268-275
[8]	RAO Lei, ZHAO Jian hua, ZHAO Zhan xi, DING Gang, GENG Mao-peng.Macro- and microstructure evolution of 5CrNiMo steel ingots during electroslag remelting process[J].Journal of Iron and Steel Research, International, 2014, 21(7):644-652
[8]	RAO Lei, ZHAO Jian hua, ZHAO Zhan xi, DING Gang, GENG Mao-peng.Macro- and microstructure evolution of 5CrNiMo steel ingots during electroslag remelting process[J].Journal of Iron and Steel Research, International, 2014, 21(7):644-652
[9]	LIU Shi qing, WANG An ren, FU Jie.The gaseous desulphurization of liquid iron during the electroslag induction melting process[J].Engineering Chemistry& metallurgy, 1994, 15(3):265-269
[9]	LIU Shi qing, WANG An ren, FU Jie.The gaseous desulphurization of liquid iron during the electroslag induction melting process[J].Engineering Chemistry& metallurgy, 1994, 15(3):265-269
[10]	LIU Fu-bin et al.Comprehensive model for a slag bath in electroslag remelting process with a current-conductive mould[J].International Journal of Minerals, Metallurgy, and Materials, 2012, 19(4):303-311
[10]	LIU Fu-bin et al.Comprehensive model for a slag bath in electroslag remelting process with a current-conductive mould[J].International Journal of Minerals, Metallurgy, and Materials, 2012, 19(4):303-311
[11]	DONG Yan wu, JIANG Zhou hua, LI Zheng bang.Mathematical model for electroslag remelting process[J].Journal of Iron and Steel Research, International, 2007, 14(5):7-13
[11]	DONG Yan wu, JIANG Zhou hua, LI Zheng bang.Mathematical model for electroslag remelting process[J].Journal of Iron and Steel Research, International, 2007, 14(5):7-13
[12]	Anon.High quality billets by electroslag rapid remelting(ESRR)[J].Steel Times International, 1997, 21(4):20-25
[12]	Anon.High quality billets by electroslag rapid remelting(ESRR)[J].Steel Times International, 1997, 21(4):20-25
[13]	Ulrich Biebricher, Harald Scholz.Electro slag remelting technologies in the past and in the future[J].MPT International, 1998, 3:36-40
[13]	Ulrich Biebricher, Harald Scholz.Electro slag remelting technologies in the past and in the future[J].MPT International, 1998, 3:36-40
[14]	Mitchell.Oxide inclusion behavior during consumable electrode remelting[J].Ironmaking and Steelmaking, 1974, (3):172-179
[14]	Mitchell.Oxide inclusion behavior during consumable electrode remelting[J].Ironmaking and Steelmaking, 1974, (3):172-179
[15]	Richling W.Inclusion behavior during ESR[J][J].Neue hutte, 1962, (1):565-569
[15]	Richling W.Inclusion behavior during ESR[J][J].Neue hutte, 1962, (1):565-569
[16]	S.R. Kay and R.J. Pomfret. .Removal of oxide inclusions during AC electroslag remelting[J].Journal of the Iron and Steel Institute, 1971, :962-965
[16]	S.R. Kay and R.J. Pomfret. .Removal of oxide inclusions during AC electroslag remelting[J].Journal of the Iron and Steel Institute, 1971, :962-965
[17]	Sindo Kou, David R.Poirier,MC. Flemings. Macrosegregation in rotated remelted ingots[J].Met Trans., 1978, 12(9B):711-719
[17]	Sindo Kou, David R.Poirier,MC. Flemings. Macrosegregation in rotated remelted ingots[J].Met Trans., 1978, 12(9B):711-719
[18]	C. Flemings. Our understanding of macrosegretion: Past and present[J].ISIJ International, 2000, (40):833-841
[18]	C. Flemings. Our understanding of macrosegretion: Past and present[J].ISIJ International, 2000, (40):833-841