1. College of Metallurgy and Energy, North China University of Science and Technology, Tangshan 063210, Hebei, China; 2. Hebei High Quality Steel Continuous Casting Technology Innovation Center,Tangshan 063009, Hebei, China; 3. Tangsteel Company, HBIS Group, Tangshan 063000, Hebei, China; 4. School of Materials Science and Engineering, Hebei University of Science and Technology, Shijiazhuang 050018, Hebei, China
Abstract:In order to analyse the influence of the cooling water supply process on the temperature field of mold copper wall and cooling water gap,based on the mold temperature data measured by thermocouples in the copper wall,a mathematical model for the inverse heat transfer question of the slab/copper wall and the forward question of the copper wall/cooling water were constructed. The numerical analysis model of the slab/copper wall/cooling water of thin slab casting mold was established by ANSYS. Coupled heat transfer analysis of the temperature field of the reactor is carried out to analyze the influence of different cooling processes on the heat transfer behavior in the high-speed thin slab continuous casting mold. The result shows that the direction of water flow in the water gap has a significant impact on the temperature field of the copper wall. The top-down "reverse water supply" is adopted,which reduces the peak temperature of the hot surface of the copper wall by 117 ℃ compared with the conventional cooling process,and the maximum temperature of the cooling water on the copper wall side Lowering 24 ℃ can effectively improve the working condition of the copper plate and suppress the local boiling tendency of cooling water. Increasing the cooling water speed can further reduce the temperature of the copper wall and the cooling water,and the cooling water temperature has less influence on the temperature field of the copper wall.
[1] 孟祥宁,王卫领,朱苗勇. 冷却结构对连铸结晶器铜板热变形的影响[J]. 北京科技大学学报,2012,34(12):1416. (MENG Xiang-ning,WANG Wei-ling,ZHU Miao-yong.Effect of cooling structure on the deformation of copper plates for slab continuous casting molds[J]. Ornal of University of Science and Technology Beijing,2012,34(12):1416.) [2] 罗伟. 异型坯连铸过程中结晶器铜板及铸坯热力行为数值模拟研究[D]. 重庆:重庆大学,2012. (LUO Wei.Numerical Investigation on Thermo-mechanical Behavior of Mold and Strand in Beam Blank Continuous Casting[D]. Chongqing:Chongqing University,2012.) [3] 杨刚,李宝宽,于洋,等. 薄板坯连铸结晶器铜板的三维传热分析[J]. 金属学报,2007,43(3):332.(YANG Gang,LI Bao-kuan,YU Yang,et al.Three dimensional heat transfer of cooling copper plate of thin slab continuous casting mold[J]. Acta Metallurgica Sinica,2007,43(3):332.) [4] 段明南,冯长宝,杨建华,等. 板坯连铸结晶器铜板热机耦合应力分析[J]. 钢铁,2008,43(5):30.(DUAN Ming-nan,FENG Chang-bao,YANG Jian-hua,et al. Thermal and mechanical couple stress analysis of mould copper for slab continuous casting[J]. Iron and Steel,2008,43(5):30.) [5] Hibbeler L C,Thomas B G,Santillana B,et al.Longitudinal face crack prediction with thermo-mechanical models of thin slabs in funnel moulds[J]. La Metallurgia Italiana,2009,101(2). [6] 王晓连,王新华,李林平,等. 高拉速下板坯连铸结晶器铜板传热行为研究[J]. 炼钢,2014,30(3):54.(WANG Xiao-lian,WANG Xin-hua,LI Lin-ping, et al. Study on heat transfer behavior of mold copper plate during high speed continuous casting of steel slabs[J]. Steelmaking,2014,30(3):54.) [7] Udayraj,Chakraborty S,Ganguly S,et al. Estimation of surface heat flux in continuous casting mould with limited measurement of temperature[J]. International Journal of Thermal Sciences,2017,118:435. [8] XIE X,CHEN D,LONG H,et al.Mathematical modeling of heat transfer in mold copper coupled with cooling water during the slab continuous casting process[J]. Metallurgical and Materials Transactions B, 2014, 45(6):2442. [9] 肖鹏程,朴占龙,朱立光,等. 超低碳钢连铸坯钩状坯壳的演变与夹杂物的捕集[J]. 工程科学学报,2018,40(9):1065. (XIAO Peng-cheng,PIAO Zhan-long,ZHU Li-guang, et al.Hook evolution and inclusion entrapment of ultralow-carbon steel slabs[J]. Chinese Journal of Engineering,2018,40(9):1065.) [10] 罗存阳. 基于传热反问题模型的薄板坯结晶器传热研究[D]. 秦皇岛:燕山大学,2017. (LUO Cun-yang.Study on Heat Transfer of Thin Slab Mold Based on Heat Transfer Inverse Problem Model[D].Qinhuangdao:Yanshan University,2017.) [11] 邹芳,田溪岩,李本文. 薄板坯连铸漏斗型结晶器内流动、传热和凝固行为的数值研究[J]. 连铸,2008(6):1.(ZOU Fang,TIAN Xi-yan,Li Ben-wen. Numerical analysis of fluid flow,heat transfer and solidification in the funnel-shaped mold of a thin slab caster[J]. Continuous Casting,2008(6):1.) [12] 王泽鹏,肖鹏程,朱立光,等. 方坯连铸结晶器铜管温度场分析[J]. 钢铁,2018,53(3):38.(WANG Ze-peng,XIAO Peng-cheng,ZHU Li-guang, et al. Temperature analysis for mold copper tube of billet continuous casting[J]. Iron and Steel,2018,53(3):38.) [13] 王朋飞. 薄板坯结晶器内三维凝固有限元分析[D]. 唐山:华北理工大学,2016. (WANG Peng-fei.Finite Element Analysis of 3D Solidification in Mold for Thin Slab[D]. Tangshan:North China University of Science and Technology,2016.) [14] 杜凤鸣,王旭东,刘宇,等. 二维结晶器铜板传热及力学行为研究[J]. 连铸,2016(5):30.(DU Feng-ming,WANG Xu-dong,LIU Yu, et al. Study on heat transfer and mechanical behavior of two dimensional mold copper plate[J]. Continuous Casting,2016(5):30.)