基于热轧全流程氧化铁皮控制的耐蚀性工艺

doi:10.13228/j.boyuan.issn0449-749x.20210073

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (2855 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要针对热轧生产流程实际工况,系统研究了热轧、卷取阶段的三次氧化铁皮演变规律,旨在不增加生产成本的前提下,通过调整热轧生产工艺控制氧化铁皮结构,利用热轧后生成的氧化铁皮作为防护屏障,提高钢材耐蚀性能。结果表明,在不同轧制温度下,三次氧化铁皮结构从外到里分别为Fe₂O₃、Fe₃O₄和FeO,由于FeO中的阳离子空位密度大,导致其比例最大,并且随着轧制温度增加,氧化铁皮中的FeO层厚度逐渐增厚,并且其比例也逐渐增加。通过模拟连续冷却试验发现氧化铁皮结构转变关系呈现出“C”曲线的形式。在450～550 ℃温度范围内卷取时,FeO发生共析反应程度达到峰值,同时可以看出在高温下卷取可以有效抑制共析转变的发生。通过大量的试验研究表明,获得以先共析Fe₃O₄为主的完整氧化铁皮的结构类型,是有效提高热轧钢材耐蚀性的主要控制方向。因此在国内某钢厂热连轧生产线进行了基于氧化铁皮控制的耐蚀性工艺试轧试验和盐雾试验,结果表明,氧化铁皮完整致密,并且其结构类型主要为先共析Fe₃O₄,因此利用轧制工艺调整改变钢板表面氧化皮结构,钢材耐蚀性能得到显著提高。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	李成刚
	单文超
	刘怡私
	杨名
	王皓
	曹光明

关键词 ：氧化铁皮, 轧制温度, 卷取温度, 共析转变, 耐蚀性能

Abstract：According to the actual working conditions of hot rolling production process,the evolution law of triple oxide iron sheet in hot rolling and coiling stage is systematically studied,aiming at improving the corrosion resistance of steel by adjusting the hot rolling production process to control the structure of oxide iron sheet and using the oxide iron sheet generated after hot rolling as protective barrier without increasing the production cost. The experimental results show that at different rolling temperatures,the structure of tri-oxide iron sheet is Fe₂O₃,Fe₃O₄ and FeO from the outside to the inside,and the proportion of FeO is the largest due to the high density of cation vacancy in FeO. With the increase of rolling temperature,the thickness of FeO layer in the iron sheet is gradually thickened,and the proportion is also gradually increased. By simulating the continuous cooling experiment,it is found that the transformation relationship of the oxide sheet structure is in the form of "C" curve. In the temperature range of 450-550 ℃,the eutectoid reaction degree of FeO reaches the peak,and it can be seen that the eutectoid transformation can be effectively inhibited by coiling at high temperature. A large number of experimental studies have shown that obtaining the structure type of complete oxide sheet with pro-eutectoid Fe₃O₄ is the main control direction to improve the corrosion resistance of hot-rolled steel effectively. So this article in a domestic steel strip production line based on the corrosion resistance of iron oxide control process to try rolling test and salt spray test,the results show that full dense iron oxide,and its structure type is mainly pro-eutectoid Fe₃O₄,so use of rolling technology to adjust the changing structure of the steel plate surface scale,steel corrosion resistant performance is improved significantly

Key words： oxide scale rolling temperature coiling temperature eutectoid transformation corrosion property

收稿日期: 2021-02-02

引用本文:

李成刚, 单文超, 刘怡私, 杨名, 王皓, 曹光明. 基于热轧全流程氧化铁皮控制的耐蚀性工艺[J]. 钢铁, 2021, 56(9): 129-135. LI Cheng-gang, SHAN Wen-chao, LIU Yi-si, YANG Ming, WANG Hao, CAO Guang-ming. Corrosion resistance process based on control of oxide scale in whole process of hot rolling[J]. Iron and Steel, 2021, 56(9): 129-135.

链接本文:

http://www.chinamet.cn/Jweb_gt/CN/10.13228/j.boyuan.issn0449-749x.20210073 或 http://www.chinamet.cn/Jweb_gt/CN/Y2021/V56/I9/129

[1] 刘振宇,李志峰. 新一代热轧板带材表面氧化铁皮控制技术的现状与进展[J]. 轧钢,2020,37(1):1.(LIU Zhen-yu,LI Zhi-feng. State of the art development on technology for new generation to controlling oxide scale of hot rolled plate and strip[J]. Steel Rolling,2020,37(1):1.)
[2] 张华,钱余海,齐慧滨,等. 汽车热轧钢板的锈蚀行为及预防措施[J]. 腐蚀与防护,2008,29(6):316.(ZHANG Hua,QIAN Yu-hai,QI Hui-bin et al. Rusting behavior and preventing measures of hot-rolled steel plates for automobile[J]. Corrosion and Protection,2008,29(6):316.)
[3] 李美栓. 金属的高温腐蚀[M]. 北京:冶金工业出版社,2001.(LI Mei-shuan. High Temperature Corrosion of Metals[M]. Beijing:Metallurgical Industry Press,2001.)
[4] Chen R Y,Yuen W Y D. Review of the high-temperature oxidation of iron and carbon steels in air or oxygen[J]. Oxidation of Metals,2003,59(5/6):433.
[5] Collazo A,Nóvoa X R,Pérez C,et al. EIS study of the rust converter effectiveness under different conditions[J]. Electrochemica Acta,2008,53(25):7565.
[6] Pérez F J,Martínez L,Hierro M P,et al.Corrosion behaviour of different hot rolled steels[J]. Corrosion Science,2005,48(2):472.
[7] 孙彬,曹光明,贾涛,等. 热轧高强钢氧化铁皮演变规律的研究[J]. 钢铁,2010,45(11):53. (SUN Bin,CAO Guang-ming,JIA Tao,et al. Study on evolution law of oxide scale of hot-rolled high strength steel[J]. Iron and Steel,2010,45(11):53.)
[8] 李鑫磊,董占斌,张跃飞,等. 轧制温度及二次除鳞对船板表面质量的影响[J]. 热加工工艺,2012,41(17):100.(LI Xin-lei,DONG Zhan-bin,ZHANG Yue-fei,et al.Influence of rolling temperature and secondary descaling on surface quality of ship plate[J]. Hot Working Technology,2012,41(17):100.)
[9] Sun W H,Tieu A K,Jiang Z Y,et al. Oxide scales growth of low-carbon steel at high temperatures[J]. Journal of Materials Processing Technology,2004,155/156:1300.
[10] Chen R Y,Yuen W Y D. Oxide-scale structures formed on commercial hot-rolled steel strip and their formation mechanisms[J]. Oxidation of Metals,2001,56(1/2):89.
[11] Chen R Y,Yuen W Y D. A study of scale structure of hot rolled steel strip by simulated coiling and cooling[J]. Oxidation of Metals,2000,53:539.
[12] Wriedt H. The Fe-O (iron-oxygen) system[J]. Journal of Phase Equilibria,1991,12(2):170.
[13] Birks N,Meier G H,Pettit F S. Introduction to the High Temperature Oxidation of Metals[M]. London:Cambridge University Press,2006.
[14] 杨名. 热轧流程氧化铁皮演变规律及耐蚀性能研究[D]. 沈阳:东北大学,2014.(YANG Ming. Study on the Evolution Law during Hot-rollling and Corrosion Properties of Oxide Scale on Hot-rolled Steel Plates[D]. Shenyang:Northeastern University,2014.)
[15] Hidaka Y,Anraku T,Otsuka N. Deformation of iron oxides upon tensile tests at 600-1 250 ℃[J]. Oxidation of Metals,2003,59(1/2):97.
[16] 顾其德,董超芳,李小刚,等. 卷曲后供氧差异对热轧带钢氧化皮组织及耐蚀性的影响[J]. 工程科学学报,2009,31(12):1564.(GU Qi-de,DONG Chao-fang,LI Xiao-gang,et al. Corrosion behavior and structure of oxide scales formed on hot rolled strips after coiling with different oxygen supplies[J]. Chinese Journal of Engineering,2009,31(12):1564.)