中高碳铝镇静钢形成MnS塑性夹杂的工艺开发与实践

doi:10.13228/j.boyuan.issn0449-749x.20210210

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (1394 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要为提高中高碳钢产品的抗疲劳性能,利用中高碳钢的成分特点,研究开发了中高碳铝镇静钢中MnS以Al₂O₃为形核质点的非均质形核工艺,将钢中Al₂O₃脆性夹杂用塑性MnS包裹,解决了疲劳应力钢因脆性非金属夹杂引起的疲劳断裂问题。通过对微细、弥散Al₂O₃夹杂生成条件、MnS非均质形核析出热力学条件的研究,开展了钢中关键元素的成分设计、精炼及连铸集成工艺的设计与开发。工业实践表明,低活度氧条件下进行铝终脱氧可以形成3～5 μm微细弥散的Al₂O₃夹杂,并作为非均质形核的核心在二次枝晶晶间的凝固末端析出弥散、细小的粒状MnS;通过梯度脱氧、真空碳脱氧以及保护浇铸等操作可以有效稳定控制钢中全氧含量,提高钢水洁净度,成品T[O]质量分数平均为0.000 618%,较原工艺的0.000 739%降低了16%;成品的夹杂物中MnS及MnS包裹Al₂O₃夹杂所占比例大于96%,与世界领先产品的夹杂物控制水平相当,考虑到产品使用过程中Al₂O₃夹杂外部的MnS包裹层必须足够厚,塑性夹杂才能起作用,建立了MnS “有效包裹率” 的概念,当硬相夹杂物被MnS包裹且硬相夹杂物的最大半径不大于MnS包裹部位半径的1/2时,认为MnS对硬相夹杂物实现了“有效包裹”;MnS塑性夹杂工艺可明显提高材料的疲劳性能,成品的平均断裂韧性为83.47 MPa·m^1/2,较原工艺的67.31 MPa·m^1/2提高了24%。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	沈昶
	陆强
	郭俊波
	杨峥

关键词 ：中高碳铝镇静钢, 非金属夹杂物, MnS塑性夹杂, 非均质形核, MnS包裹Al₂O₃

Abstract：In order to improve the fatigue resistance of medium and high carbon steel products, based on the composition characteristics of medium and high carbon steel, the process which the heterogeneous nucleation of MnS in steel takes Al₂O₃ as nucleation particle is developed, and the brittle inclusions of Al₂O₃ in steel is wrapped by plastic MnS, the problem of fatigue fracture caused by brittle nonmetallic inclusion is solved. The composition design of key elements in steel, the design and development of refining and continuous casting integrated process were carried out by studying the formation conditions of fine and dispersed Al₂O₃ inclusions and the thermodynamic conditions of MnS heterogeneous nucleation and precipitation. Industrial practice shows that,the final deoxidation by aluminum with low activity oxygen can form 3-5 μm fine dispersed Al₂O₃inclusions, which act as the core of heterogeneous nucleation and precipitate dispersed and fine granular MnS at the solidification end of secondary dendrites; through gradient deoxidation, vacuum carbon deoxidation and protective casting, the total oxygen content in steel can be effectively controlled and the purity of molten steel can be improved,the average mass percent of T[O] of the finished product is 0.000 618%, which is 16% lower than 0.000 739% of the original process;the proportion of MnS and MnS wrapped Al₂O₃ inclusions is more than 96% of the total inclusions in the finished product,which is equivalent to the inclusion control level of the world′s leading products, considering that the Al₂O₃ inclusion wrapped by MnS must be thick enough for the plastic inclusion to work,the concept of "effective package rate" of MnS is established,while the maximum radius of hard inclusion was not more than 1/2 of radius of MnS wrapping part, it is considered that MnS realizes "effective wrapping" of hard phase inclusions;the average fracture toughness of the finished product is 83.47 MPa·m^1/2, which is 24% higher than 67.31 MPa·m^1/2 of the original process.

Key words： medium high carbon Al killed steel non-metallic inclusion MnS plastic inclusion heterogeneous nucleation MnS wrapped Al₂O₃

收稿日期: 2021-04-14

引用本文:

沈昶, 陆强, 郭俊波, 杨峥. 中高碳铝镇静钢形成MnS塑性夹杂的工艺开发与实践[J]. 钢铁, 2021, 56(12): 62-67. SHEN Chang, LU Qiang, GUO Jun-bo, YANG Zheng. Development and practice on forming MnS plastic inclusion in medium high carbon Al killed steel[J]. Iron and Steel, 2021, 56(12): 62-67.

链接本文:

http://www.chinamet.cn/Jweb_gt/CN/10.13228/j.boyuan.issn0449-749x.20210210 或 http://www.chinamet.cn/Jweb_gt/CN/Y2021/V56/I12/62

[1] 姜锡山. 钢中非金属夹杂物[M]. 北京:冶金工业出版社, 2011.(JIANG Xi-shan. Nonferrous Inclusion in Steel[M]. Beijing: Metallurgical Industry Press, 2011.)
[2] 徐国军, 胡华东, 田川, 等. Al₂O₃夹杂在DC06钢中的分布及对深冲性能的影响[J]. 中国冶金, 2021, 31(5): 111.(XU Guo-jun, HU Hua-dong, TIAN Chuan, et al. Distribution of Al₂O₃ inclusions in DC06 steel and its effect on deep drawing properties[J]. China Metallurgy, 2021, 31(5): 111.)
[3] 李明钢,刘润藻,林腾昌,等.GCr15轴承钢中非金属夹杂物的转变[J].钢铁研究学报,2014,26(5):56.(LI Ming-gang, LIU Run-zao, LIN teng-chang et al. Transformation of non-metallic inclusions in GCr15 bearing steel [J].Journal of Iron and Steel Research,2014,26(5):56.)
[4] 王博,姜周华,龚伟,等.GCr15轴承钢夹杂物及全氧含量控制工艺分析[J].材料与冶金学报,2004,3(2):90.(WANG Bo, JIANG Zhou-hua, GONG Wei, et al. Analysis of inclusions and total oxygen content control in bearing steel of GCr15 [J].Journal of Materials and Metallurgy,2004,3(2):90.)
[5] WANG L, YANG S, LI J, et al. Effect of Mg addition on the refinement and homogenized distribution of inclusions in steel with different Al contents[J]. Metallurgical and Materials Transactions B, 2017, 48(2):805.
[6] 周彦召,邹长东. 铝镇静特殊钢B类非金属夹杂物原因分析与控制[J]. 中国冶金, 2018, 28(4): 48.(ZHOU Yan-zhao,ZOU Chang-dong. Cause analysis and control of B type non-metallic inclusions of Al killed special steel[J]. China Metallurgy, 2018, 28(4): 48.)
[7] 陈然, 陈兆平, 徐迎铁,等. 轴承钢夹杂物行为的原位观察[J]. 钢铁研究学报, 2015, 27(12):48.(CHEN Ran,CHEN Zhao-ping, XU Ying-tie, et al. In-situ observation of behaviors of inclusions in bearing steel[J]. Journal of Iron and Steel Research, 2015, 27(12):48.)
[8] Xuan C, Karasev A V, Pär Göran Jönsson, et al. Attraction force estimations of Al₂O₃ particle agglomerations in the melt[J]. Steel Research International, 2017, 88(2):382.
[9] 陈家祥.钢铁冶金学[M].北京:冶金工业出版社,2009.(CHEN Jia-xiang. Steel Metallurgy[M].Beijing:Metallurgical Industry Press, 2009.)
[10] 张志刚, 任英, 成功,等. 非调质钢中夹杂物生成热力学[J]. 中国冶金, 2020, 30(4): 23.(ZHANG Zhi-gang, REN Ying, CHENG Gong, et al. Thermodynamic of inclusion formation in non-tempered steel[J]. China Metallurgy, 2020, 30(4): 23.)
[11] Wakoh M, Sawai T, Mizoguchi S. Effect of S content on the MnS precipitation in steel with oxide nuclei[J]. ISIJ International, 1996, 36(8): 1014.
[12] Ohta H, Suito H. Characteristics of particle size distribution of deoxidation products with Mg, Zr, Al, Ca, Si/Mn and Mg/Al in Fe-10 mass%Ni alloy[J]. ISIJ International, 2006, 46(1):14.
[13] Ohta H, Suito H. Dispersion behavior of MgO, ZrO₂, Al₂O₃, CaO-Al₂O₃ and MnO-SiO₂ deoxidation particles during solidification of Fe-10 mass%Ni alloy[J]. ISIJ International, 2006, 46(1): 22.
[14] 林腾昌, 门兵, 程雄, 等. 热处理对铸态钢中硫化锰夹杂物的影响[J].中国冶金, 2021, 31(4): 48.(LIN Teng-chang, MEN Bing, CHENG Xiong, et al. Influence of heat treatment on MnS inclusion in as-cast steel[J]. China Metallurgy, 2021, 31(4): 48.)
[15] 雷少龙,姜敏,杨叠,等. Al脱氧钢中氧化物对MnS析出的影响[J].北京科技大学学报,2013,35(11):1443.(LEI Shao-long, JIANG Min, YANG Die, et al.Effect of oxides on MnS precipitation in aluminum-deoxidized steel[J].Journal of University of Science and Technology Beijing, 2013,35(11):1443.)
[16] Oh Y J,Lee S Y,Byun J S,et al. Non-metallic inclusions and acicular ferrite in low carbon steel[J]. Materials Transactions JIM,2000,41(12):1663.
[17] 宋波,毛璟红,王福明,等. 非调质钢中Ti脱氧产物析出行为[J].北京科技大学学报,2006,28(3):90.(SONG Bo, MAO Jing-hong, WANG Fu-ming, et al. Precipitation behavior of ti-deoxidized products in non-quenched and tempered steel [J]. Journal of University of Science and Technology Beijing, 2006, 28(3):90.)