Abstract：Accurate rolling model is the key to production of high-quality strips. Currently, the commonly used hot rolling model is only suitable for studying the static rolling process. When faced with dynamic rolling processes such as variable thickness rolling and rolling mill vibration, the model structure lacks integrity since the commonly used static model does not include the roll gap change speed parameters. In order to conduct a comprehensive and in-depth study on dynamic rolling, it is necessary to establish a dynamic rolling model which includes the parameters of roll gap change speed. Based on the Orowan equation, the dynamic velocity field model, the average deformation rate model and the force differential balance equation were established while considering the influence of roll gap change speed on the average deformation rate of strip and the length of deformation zone, and the analytical solution of dynamic rolling force was finally solved. A two-high experimental rolling mill was used to carry out dynamic rolling experiments. Comparing with the results of dynamic hot rolling experiments, the dynamic rolling model had high accuracy, which could provide theoretical guidance for precise preparation of dynamic rolling forces. Through analysis, it is found that when the roll gap change rate is zero, the model in this paper is the same as SIMS model. Change law of various process parameters for the dynamic rolling process in the model above was analyzed. The results show that the strip exit position deviates from the line of two work roll centers during dynamic rolling, and the deviation direction and size are directly affected by the size and direction of roll gap change speed. Under the same rolling schedule, when the roll gap is reduced, the rolling force is greater than that of static rolling, while roll gap is increased, the rolling force is less than that of static rolling. This is because the length of deformation zone and metal deformation rate in the roll gap are affected by size and direction of roll gap change speed. In addition, when the roll gap is reduced, the rolling force will decrease with the increase of the rolling speed.
杨彦博, 彭艳, 刘洋, 刘才溢, 王瑾. 考虑辊缝变化的板带热轧动态理论模型[J]. 钢铁, 2022, 57(2): 85-93.
YANG Yan-bo, PENG Yan, LIU Yang, LIU Cai-yi, WANG Jin. Dynamic theoretical model of strip hot rolling considering change of roll gap[J]. Iron and Steel, 2022, 57(2): 85-93.
[1] 李晓青,魏立群,付斌,等.冷轧铜-铝复合带翘曲变形研究[J].上海金属,2021,43(5):85.(LI Xiao-qing, WEI Li-qun, FU Bin,et al.Research on warping of cold-rolled copper-aluminum composite strip[J]. Shanghai Metals,2021,43(5):85.) [2] 连全勇,王立新,袁峰,等.轧制温度和轧制道次对Mg-1RE-0.5Zn-0.5Zr合金组织和性能的影响[J].上海金属,2020,42(5):105.(LIAN Quan-yong,WANG Li-xin,YUAN Feng,et al. Effect of rolling temperature and rolling pass on microstructure and properties of Mg-1RE-0.5Zn-0.5Zr alloy[J]. Shanghai Metals, 2020,42(5):105.) [3] 叶其斌, 王益民, 阚立烨, 等. 动态相变制备超细晶钢理论研究进展[J]. 轧钢, 2021, 38(3): 64.(YE Qi-bin, WANG Yi-min, KAN Li-ye, et al. Research on ultrafine grain steel prepared bydynamic transformation[J]. Steel Rolling, 2021, 38(3): 64.) [4] 沈新玉, 宫峰, 裴洪涛, 等. 宽幅冷轧带钢连退跑偏影响因素的定量分析研究[J]. 轧钢, 2021, 38(4): 44.(SHEN Xin-yu, GONG Feng, PEI Hon-gtao, et al. Quantitative analysis and research on influence factors of cold rolled wide gauge strip deviation during continuous annealing[J]. Steel Rolling, 2021, 38(4): 44.) [5] Orowan E. The calculation of roll pressure in hot and cold flat rolling[J]. Proceedings of the Institution of Mechanical Engineers, 1943, 150:140. [6] Sims R B. Calculation of roll force and torque in hot rolling mills[J]. Proceedings of the Institution of Mechanical Engineers, 1954, 168:191. [7] Bland D R, Ford H. The calculation of roll force and torque in cold strip rolling with tensions[J]. Proceedings of the Institution of Mechanical Engineers, 1948, 159:144. [8] CHEN S X, LI W G, LIU X H. Calculation of rolling pressure distribution and force based on improved Karman equation for hot strip mill[J]. International Journal of Mechanical Sciences, 2014, 89:256. [9] 宜亚丽,韩晓铠,金贺荣. 带夹层不锈钢复合板异步轧制力数学模型研究[J]. 钢铁, 2020,55(9):69.(YI Ya-li, HAN Xiao-kai, JIN He-rong. Research on mathematical model of asymmetric rolling force of sandwich clad plate[J]. Iron and Steel, 2020,55(9):69.) [10] 冀秀梅, 王龙, 高克伟, 等. 极限学习机在中厚板轧制力预报中的应用[J]. 钢铁研究学报, 2020, 32(5):47.(JI Xiu-mei, WANG Long, GAO Ke-wei, et al. Application of ELM to predict plate rolling force[J]. Journal of Iron and Steel Research, 2020,32(5):47.) [11] Hu P H, Ehmann K F. A dynamic model of the rolling process. Part I: homogeneous model[J]. International Journal of Machine Tools and Manufacture, 2000, 40(1):1. [12] 杜平,胡贤磊,王君,等. 纵向变截面轧制过程中的轧制参数[J]. 钢铁研究学报, 2008(12):26.(DU Ping, HU Xian-lei, WANG Jun, et al. Rolling parameters for longitudinal profiled plate rolling process[J]. Journal of Iron and Steel Research, 2008(12):26.) [13] GAO Z Y, LIU Y, ZHANG Q D, et al. Chatter model with structure-process-control coupled and stability analyses in the cold rolling system[J]. Mechanical Systems and Signal Processing, 2020, 140(6):106692.1. [14] CAO L, LI X, WANG Q L, et al. Vibration analysis and numerical simulation of rolling interface during cold rolling with unsteady lubrication[J]. Tribology International, 2021, 153. [15] Hu P H, Ehmann K F. A dynamic model of the rolling process. Part II: homogeneous model[J]. International Journal of Machine Tools and Manufacture, 2000, 40(1):21. [16] YANG Y B, PENG Y. Dynamic rolling model based on uniform deformation[J]. Journal of Manufacturing Processes, 2020, 58:1334. [17] 王卫卫. 5052铝板带热连轧全流程温度计算模型研究[D]. 长沙:中南大学,2012.(WANG Wei-wei. The Study on the Temperature Calculation Model of 5052 Al Plate in Hot Continuous Rolling[D]. Changsha: Central South University,2012.)
2022, Vol. 57 
