铝硅比对烧结成矿特性及冶金性能的影响

doi:10.13228/j.boyuan.issn0449-749x.20210537

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (3328 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要 Al₂O₃和SiO₂是复合铁酸钙的重要组分,适宜的铝硅比是获得良好烧结成矿特性和冶金性能的重要条件。基于某钢厂现场烧结原料结构,运用FactSage理论计算了烧结体系的平衡物相组成及液相组分变化规律,随着铝硅比由0.41降至0.34,烧结矿中液相、铁氧化物等优质物相含量增加,尖晶石等劣质物相含量下降,且液相中析出复合铁酸钙逐渐增多。试验揭示了不同铝硅比对烧结矿产质量、物相组成、微观结构及冶金性能的影响规律,结果表明,随着铝硅比由0.41降低到0.34,烧结矿转鼓强度、成品率、利用系数等指标显著改善,分别由58.27%、60.24%、1.585 t/(m²·h)提高至61.73%、71.87%、2.185 t/(m²·h)。矿相分析表明,随着铝硅比降低,铁酸钙含量增加并逐步向针状发展,赤铁矿、磁铁矿及孔洞含量降低,并在铝硅比为0.34时达到最佳物相组成,该结果佐证了烧结矿产质量指标变化规律。铝硅比为0.34时烧结矿冶金性能比基准烧结矿冶金性能提升,其中还原度和低温还原粉化指数RDI>3.15 mm分别由73.11%、72%提升至77.47%、80%,软化温度区间和熔滴温度区间变窄,熔滴性能总特性值S也有下降趋势,烧结矿软熔性改善明显。根据理论计算及试验结果,提出的优化配矿建议对提高烧结矿产质量、优化烧结工艺具有重要的意义。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	杨涛
	龙红明
	丁成义
	李勇
	曹发卫
	胡明意

关键词 ：高碱度烧结, 铝硅比, 复合铁酸钙, 成矿特性, 冶金性能

Abstract：Al₂O₃ and SiO₂ are important components of composite calcium ferrite, and an appropriate ratio of alumina to silica is an important condition for obtaining good sintering ore-forming characteristics and metallurgical properties. Based on the on-site sintering raw material structure of a steel plant, the FactSage theory was used to calculate the change law of equilibrium phase composition and liquid phase composition for the sintering system. As the ratio of alumina to silica decreased from 0.41 to 0.34, the high-quality phases such as liquid phase and iron oxide in the sinter increased, the content of inferior phases such as spinel decreased, and the liquid phase precipitates and SFCA gradually increased. The experiment revealed the influence of different ratio for alumina to silica on the quality, phase composition, microstructure and metallurgical properties of sinters. The results showed that as the ratio of alumina to silica decreased from 0.41 to 0.34, the drum strength, yield and utilization factor of sinters improved significantly, from 58.27%, 60.24%, 1.585 t/(m²·h) to 61.73%, 71.87%, and 2.185 t/(m²·h), respectively. The mineral phase analysis shows that as the ratio of alumina to silica decreases, the content of calcium ferrite increases and gradually develops into acicular shape, while the content of hematite, magnetite and pores decreases, and the optimal phase composition is reached when the ratio of alumina to silica is 0.34. This result corroborates the change rule of sintered ore quality index. When the ratio of alumina to silica is 0.34, the metallurgical performance of sinter is improved compared with the benchmark sinter. The reduction degree and reduction degradation property index RDI>3.15 mm are increased from 73.11% and 72% to 77.47% and 80% respectively, the softening temperature range and the droplet temperature range are narrowed, the total characteristic value S of the droplet performance also has a downward trend, and the soft melting property of sinter is improved significantly. According to the theoretical calculation and test results, the optimization of ore blending is of great significance for improving the quality of sintered minerals and optimizing sintering process.

Key words： high basicity sintering w(Al₂O₃)/ w(SiO₂) SFCA mineralization characteristic metallurgical property

收稿日期: 2021-09-03

引用本文:

杨涛, 龙红明, 丁成义, 李勇, 曹发卫, 胡明意. 铝硅比对烧结成矿特性及冶金性能的影响[J]. 钢铁, 2022, 57(4): 43-51. YANG Tao, LONG Hong-ming, DING Cheng-yi, LI Yong, CAO Fa-wei, HU Ming-yi. Effect of w(Al₂O₃)/w(SiO₂) on sintered ore mineralization characteristics and metallurgical properties[J]. Iron and Steel, 2022, 57(4): 43-51.

链接本文:

http://www.chinamet.cn/Jweb_gt/CN/10.13228/j.boyuan.issn0449-749x.20210537 或 http://www.chinamet.cn/Jweb_gt/CN/Y2022/V57/I4/43

[1] 国家发展和改革委员会.钢铁行业2020年1—12月运行情况[J]. 冶金自动化, 2021,45(2): 67.(National Development and Reform Commission. Operation of steel industry from January to December 2020[J]. Metallurgical Industry Automation, 2021,45(2): 67.)
[2] 沈峰满,郑海燕,姜鑫,等. 高炉炼铁工艺中Al₂O₃的影响及适宜w(MgO)/w(Al₂O₃)的探讨[J]. 钢铁, 2014,49(1): 1.(SHEN Feng-man,ZHENG Hai-yan,JIANG Xin,et al. Influence of Al₂O₃ in blast furnace smelting and discussions on proper w(MgO)/w(Al₂O₃) ratio[J]. Iron and Steel, 2014,49(1): 1.)
[3] 罗云飞,杨涛,周江虹,等. 料面喷吹蒸汽对烧结矿产质量和CO排放的影响[J]. 钢铁,2021,56(11): 47.(LUO Yun-fei,YANG Tao,ZHOU Jiang-hong,et al. Effect of steam injection from material surface on output and quality of sinter and CO emissions[J]. Iron and Steel,2021,56(11): 47.)
[4] Webster N A S, Pownceby M I, Manuel J R,et al. Fundamentals of silico-ferrite of calcium and aluminum (SFCA) and SFCA-I iron ore sinter bonding phase formation: Effects of MgO on phase formation during heating[J]. JOM,2021, 73(1): 299.
[5] 孟凡俭,孙长余,李廷乐,等. 烧结矿中复合铁酸钙形成影响因素[J]. 钢铁,2018,53(7): 16.(MENG Fan-jian,SUN Chang-yu,LI Ting-le,et al. Formation and influencing factors of silico-ferrite of calcium and aluminum in sinter[J]. Iron and Steel,2018,53(7): 16.)
[6] ZHU De-qing,XUE Yu-xiao,PAN Jian,et al. An investigation into aluminum occurrence impact on SFCA formation and sinter matrix strength[J]. Journal of Materials Research and Technology,2020,9(5): 10223.
[7] 牛乐乐,刘征建,张建良,等. 铁矿粉矿物组成对烧结矿冶金性能的影响[J]. 钢铁, 2019,54(9): 27.(NIU Le-le,LIU Zheng-jian,ZHANG Jian-liang,et al. Effect of mineral composition of iron ore on metallurgical properties of sinter[J]. Iron and Steel,2019,54(9): 27.)
[8] 史先菊,王强,李光强,等.熔剂颗粒在烧结过程中的特征演变及影响[J].钢铁,2021,56(12):28.(SHI Xian-ju,WANG Qiang,LI Guang-qiang,et al. Characteristic evolution and corresponding influence of flux particles in sintering process[J]. Iron and Steel,2021,56(12):28.)
[9] 张国成,罗果萍,宋巍,等.MgO对烧结矿液相形成性能和微观结构特性的影响[J].中国冶金,2021,31(10):8.(ZHANG Guo-cheng,LUO Guo-ping,SONG Wei,et al. Effect of MgO on liquid phase formation properties and microstructure of sinter[J]. China Metallurgy,2021,31(10):8.)
[10] 韩秀丽,司天航,刘盈盈,等.不同含量Al₂O₃烧结矿矿相结构与RDI_{+3.15 mm}的定量关系[J].中国冶金,2022,32(2):34.(HAN Xiu-li,SI Tian-hang,LIU Ying-ying,et al. Relationship between mineralogical structure and RDI_{+3.15 mm} of sinter with different contents of Al₂O₃[J]. China Metallurgy,2022,32(2):34.)
[11] Sinha M,Ramna R V. Effect of variation of alumina on the microhardness of iron ore sinter phases[J]. ISIJ International, 2009,49(5): 719.
[12] 闫志武,张建良,张亚鹏,等. SiO₂对烧结矿冶金性能及微观结构的影响[J]. 工程科学学报,2016,38(7): 913.(YAN Zhi-wu,ZHANG Jian-liang,ZHANG Ya-peng,et al. Effects of SiO₂on the metallurgical properties and microstructure of sinter[J]. Chinese Journal of Engineering, 2016,38(7):913.)
[13] WU Sheng-li,ZHANG Guo-liang,CHEN Shao-guo,et al. Influencing factors and effects of assimilation characteristic of iron ores in sintering process[J]. ISIJ International, 2014,54(3): 582.
[14] Umadevi T, Sah R, Mahapatra P C. Influence of sinter basicity (CaO/SiO₂) on low and high alumina iron ore sinter quality[J]. Mineral Processing and Extractive Metallurgy, 2014,123(2): 75.
[15] 司天航,韩秀丽,刘磊,等. 镁铝对烧结矿矿相结构的影响规律[J]. 烧结球团,2021,46(2): 24.(SI Tian-hang,HAN Xiu-li,LIU Lei,et al. Influence of Mg and Al on mineralogical structure in sinter[J]. Sintering and Pelletizing,2021,46(2): 24.)
[16] 付忠旺,莫朝兴,陈小敏,等. 铁矿粉烧结液相流动性特征数的影响因素[J]. 钢铁,2018,53(12): 18.(FU Zhong-wang,MO Chao-xing,CHEN Xiao-min,et al.Influence factors of fluidity characteristic number of iron ore powder[J]. Iron and Steel, 2018,53(12): 18.)
[17] DONG J J,WANG G,GONG Y G,et al. Effect of high alumina iron ore of gibbsite type on sintering performance[J]. Ironmaking and Steelmaking,2015,42(1): 34.
[18] GUO Hui,GUO Xing-Min. Mechanism of low-temperature reduction degradation of alumina-containing hematite solid solution below 550 ℃[J]. Metallurgical and Materials Transactions B, 2018,49(6): 3513.
[19] Jeon J,Kim S,Suh I,et al. Assimilation behavior of quasi-particle comprising high alumina pisolitic ore[J]. ISIJ International, 2014,54(12): 2713.
[20] 王喆,张建良,左海滨,等. Al₂O₃质量分数对高碱度烧结矿软熔滴落性能影响[J]. 钢铁,2015,50(7): 20.(WANG Zhe,ZHANG Jian-liang,GUO Bing,et al. Influence of Al₂O₃content on the fluidity behavior of primary melts in sintering process[J]. Iron and Steel,2015,50(7): 20.)
[21] 武轶. Al₂O₃含量对烧结矿性能的影响[J]. 钢铁研究,2005(6): 5.(WU Yi. Effect of Al₂O₃ content of sinter sinter properties[J]. Research on Iron and Steel, 2005(6): 5.)
[22] 范晓慧,孟君,陈许玲,等. 铁矿烧结中铁酸钙形成的影响因素[J]. 中南大学学报(自然科学版), 2008,39(6): 1125.(FAN Xiao-hui,MENG Jun,CHEN Xu-ling,et al. Influence factors of calcium ferrite formation in iron ore sintering[J]. Journal of Central South University(Nature Science),2008,39(6): 1125.)
[23] 陈子罗,张建良,张亚鹏,等. 烧结矿适宜的SiO₂质量分数和碱度[J]. 钢铁, 2016,51(12): 8.(CHEN Zi-luo,ZHANG Jian-liang,ZHANG Ya-peng,et al. Influence of basicity and w(SiO₂) on sinter mineral quality[J]. Iron and Steel, 2016,51(12): 8.)
[24] 张芳,安胜利,罗果萍,等. 包钢低硅烧结矿铁酸钙生成特性的影响因素[J]. 钢铁研究学报, 2012,24(2): 24.(ZHANG Fang,AN Sheng-li,LUO Guo-ping,et al. Influencing factors in formation characteristics of SFCA for low silica of Baogang[J]. Journal of Iron and Steel Research,2012,24(2): 24.)
[25] 杨楠,郭兴敏. SiO₂对CaO-Fe₂O₃熔体结晶矿物组成及显微结构的影响[J].钢铁研究学报,2019,31(8): 712.(YANG Nan,GUO Xing-min. Effect of SiO₂ on composition and microstructure of crystal products of CaO-Fe₂O₃ melt[J]. Journal of Iron and Steel Research,2019,31(8): 712.)
[26] 苏立新,吴胜利,翟晓波,等. 巴西某高硅铁矿粉对烧结黏结相流动性及劣质矿物的影响[J]. 中国冶金, 2020,30(1): 18.(SU Li-xin,WU Sheng-li,ZHAI Xiao-bo, et al. Effect of high-silica iron ore from Brazil on fluidity and inferior minerals of sintered binding phase[J]. China Metallurgy, 2020,30(1): 18.)
[27] JI Zhi-yun,ZHAO Yuan-jie,GAN Min,et al. Microstructure and minerals evolution of iron ore sinter: Influence of SiO₂and Al₂O₃ [J]. Minerals,2019,9(7): 449.
[28] 刘晓荣,邱冠周,蔡汝卓,等. Al₂O₃/SiO₂对低温烧结成矿规律的影响[J]. 钢铁,2001,36(3): 5.(LIU Xiao-rong,QIU Guan-zhou,CAI Ru-zhuo,et al. Effect of Al₂O₃/SiO₂ ratio on mineralizing laws for low-temperature sintering[J]. Iron and Steel,2001,36(3): 5.)
[29] 罗果萍,王成林,吴胜利. 铝硅比对白云鄂博铁精矿烧结液相流动性的影响[J]. 内蒙古科技大学学报, 2014,33(2): 132.(LUO Guo-ping,WANG Cheng-lin,WU Sheng-li. The effect of alumina-silica ratio on the sintering flow characteristics of iron ore from Baiyunebo[J]. Journal of Inner Mongolia University of Science and Technology,2014,33(2): 132.)
[30] 王建芳,孙艳芹,赵文书,等. Al₂O₃/SiO₂对烧结矿铁酸钙生成能力的影响[J]. 烧结球团,2021,46(1): 43.(WANG Jian-fang,SUN Yan-qin,ZHAO Wen-shu,et al. Influence of Al₂O₃/SiO₂ on formation ability of calcium ferrite in sinter[J]. Sintering and Pelletizing,2021,46(1): 43.)
[31] ZHANG Fan,AN Sheng-li,LUO Guo-ping,et al. Effect of basicity and alumina-silica ratio on formation of silico-ferrite of calcium and aluminum[J]. Journal of Iron and Steel Research, International,2012,19(4): 1.
[32] 张新建,朱博洪,牛德良,等. Al₂O₃/SiO₂对烧结矿冶金性能的影响[J]. 重庆理工大学学报(自然科学),2014,28(2): 40.(ZHANG Xin-jian,ZHU Bo-hong,NIU De-liang,et al. Influence of Al₂O₃/SiO₂on sinter for its metallurgical properties[J]. Journal of Chongqing University of Technology(Natural Science),2014,28(2): 40.)
[33] 杨楠,郭兴敏. Al₂O₃对CaO-Fe₂O₃熔体结晶矿物组成及显微结构的影响[J]. 钢铁钒钛,2019,40(2): 132.(YANG Nan,GUO Xing-min. Effect of Al₂O₃ on the composition and microstructures of crystal products of CaO-Fe₂O₃ melt[J]. Iron Steel Vanadium Titanium, 2019,40(2): 132.)