超高强铁素体/贝氏体双相钢的控轧控冷

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (0 KB) HTML (0 KB)
Export: BibTeX | EndNote (RIS)

Abstract Controlled rolling and cooling of ultra-high strength ferrite-bainite dual phase steel in the different conditions were conducted by a laboratory hot rolling mill. Effect of various processing parameters on the microstructure and mechanical properties of the steel was investigated. The results show that ultra-high strength dual phase steel with ferrite-bainite microstructure can be obtained by applying controlled rolling and cooling. The tensile strength values are nearly the same in all cases and always exceed 1000MPa, yield ratio varies from 0.54 to 0.62 and the total elongation varies from 13% to 17% for the specimens which are cooled at different cooling rates after various finish rolling temperatures. The ferrite grains are refined with decreasing finish rolling temperature and accelerating cooling, and the amount of bainite increases with decreasing finish cooling temperature. Tensile strength, total elongation and the product of tensile strength and total elongation for the specimen, which is finished rolling at 800℃ and subsequent laminar cooling to 560℃ and then air cooling to room temperature, reach maximum values (1130MPa, 16% and 18080MPa%, respectively). This is attributed to the ferrite-grain refinement, strengthening of granular bainite, carbide free bainite and a small amount of twinning martensite. The presence of retained austenite improves the ductility of the steel. Multiphase microstructures contain ferrite and bainite as main phase with a small amount of retained austenite and martensite, contribute to enhance mechanical properties of tested steel.

Received: 11 October 2011 Published: 05 September 2012

PACS:

TG333.7

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	WU Di
	LI Zhuang

Cite this article:

WU Di,LI Zhuang. Controlled Rolling and Cooling of Ultra-High Strength Ferrite-Bainite Dual Phase Steel[J]. Iron and Steel, 2012, 47(8): 36-42.

URL:

http://www.chinamet.cn/Jweb_gt/EN/ OR http://www.chinamet.cn/Jweb_gt/EN/Y2012/V47/I8/36

[1]	康永林，陈贵江，朱国明等，.新一代汽车用先进高强钢的成形与应用[J].钢铁,2010,45(8 ):1-19
[1]	康永林，陈贵江，朱国明等，.新一代汽车用先进高强钢的成形与应用[J].钢铁,2010,45(8 ):1-19
[2]	Saeidi N，Ekrami A.Comparison of Mechanical Properties of Martensite/Ferrite and Bainite/Ferrite Dual Phase 4340 Steels[J].Materials Science & Engineering A,2009,A523:125-
[2]	Saeidi N，Ekrami A.Comparison of Mechanical Properties of Martensite/Ferrite and Bainite/Ferrite Dual Phase 4340 Steels[J].Materials Science & Engineering A,2009,A523:125-
[3]	Ming Hui C, Hua D, Zheng You T, et al.Strain Hardening Behavior of High Performance FBDP, TRIP and TWIP Steels[J].,2011,82(3):242-248
[3]	Ming Hui C, Hua D, Zheng You T, et al.Strain Hardening Behavior of High Performance FBDP, TRIP and TWIP Steels[J].,2011,82(3):242-248
[4]	Yu Zolotarevskii N, Titovets Yu F, Samoilov A N, et al.Modeling of Structure of Double-Phase Low-Carbon Chromium Steels[J].Metal Science and Heat Treatment,2007,49(1-2):10-16
[4]	Yu Zolotarevskii N, Titovets Yu F, Samoilov A N, et al.Modeling of Structure of Double-Phase Low-Carbon Chromium Steels[J].Metal Science and Heat Treatment,2007,49(1-2):10-16
[5]	方鸿生，工家军，杨志纲，等. 贝氏体相变.[J].科学出版社,1999,:-
[5]	方鸿生，工家军，杨志纲，等. 贝氏体相变.[J].科学出版社,1999,:-
[6]	Weng Y Q, Sun X J, Dong H, et al.Overview on the Theory of Deformation Induced Ferrite Transformation[J].Iron & Steel Supplement,2005,40:9-15
[6]	Weng Y Q, Sun X J, Dong H, et al.Overview on the Theory of Deformation Induced Ferrite Transformation[J].Iron & Steel Supplement,2005,40:9-15
[7]	Quidort D and Breehet Y.The role of carbon on the kinetics of bainite transformation in steels[J].,2002,47(3):151-156
[7]	Quidort D and Breehet Y.The role of carbon on the kinetics of bainite transformation in steels[J].,2002,47(3):151-156
[8]	翁宇庆等著.超细晶钢－钢的组织细化理论与控制技术[J].冶金工业出版社,2003,20:497-
[8]	翁宇庆等著.超细晶钢－钢的组织细化理论与控制技术[J].冶金工业出版社,2003,20:497-