转炉底吹枪优化布置的数值模拟

doi:10.13228/j.boyuan.issn0449-749x.20170361

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (2104 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract In order to optimize stirring effect of converter bottom blowing， based on the converter in a steel plant， a three-dimensional Euler mathematical model was established through the commercial software Ansys-Fluent to study the effect of the number of bottom tuyeres on the mixing behaviors of the molten metal in converter. The results indicate that with 4 bottom tuyeres and large flow through each tuyere， the recirculation zone develops fully and the blocking of tuyeres can be controlled. Meanwhile， the average velocity of the molten metal is large， the coverage of weak zone， low velocity zone and dead zone are small and the mixing time is short. Therefore， 4 bottom tuyeres is the best number of the bottom tuyeres. For the distribution of 8 and 12 bottom tuyeres arranged closely， the flow fields are similar to the one of 4 tuyeres， but the energy utilization rate is lower. The arrangement of multiple tuyeres is beneficial to the mixing of upper half of the molten pool. However， with more bottom tuyeres， the flow rate of the gas through per bottom tuyere is smaller， so the mixing effect at the bottom of converter is bad. Practices show that the technical indexes of the converter are greatly improved at the end of smelting when using the arrangement of 4 bottom tuyeres， which is consistent with the results through numerical simulation.

Key words： converter bottom tuyeres argon blowing stirring numerical simulation

Received: 13 July 2017 Published: 26 February 2018

PACS:

TF748.215

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	LI Jiao
	YU Hui-Xiang
	YU Xin-Hua
	GAO Pan
	LI Hai-Bei

Cite this article:

LI Jiao,YU Hui-Xiang,YU Xin-Hua等. Optimization of arrangement of bottom tuyeres through numerical simulation[J]. Iron and Steel, 2018, 53(2): 32-39.

URL:

http://www.chinamet.cn/Jweb_gt/EN/10.13228/j.boyuan.issn0449-749x.20170361 OR http://www.chinamet.cn/Jweb_gt/EN/Y2018/V53/I2/32

[1]	Martín M, Rendueles M, Díaz M. Steel-Slag Mass Transfer in Steel Converter, Bottom and Top/Bottom Combined Blowing Through Cold Model Experiments[J]. Chemical Engineering Research & Design, 2005, 83(9):1076.
[1]	Martín M, Rendueles M, Díaz M. Steel-Slag Mass Transfer in Steel Converter, Bottom and Top/Bottom Combined Blowing Through Cold Model Experiments[J]. Chemical Engineering Research & Design, 2005, 83(9):1076.
[2]	Zhou X, Ersson M, Zhong L, et al. Numerical Simulations of the Kinetic Energy Transfer in the Bath of a BOF Converter[J]. Metallurgical and Materials Transactions B, 2016, 47(1):434.
[2]	Zhou X, Ersson M, Zhong L, et al. Numerical Simulations of the Kinetic Energy Transfer in the Bath of a BOF Converter[J]. Metallurgical and Materials Transactions B, 2016, 47(1):434.
[3]	王新华. 炼钢生产工艺技术进展[N]. 世界金属导报, 2014-05-20(B02).WANG Xin-hua. Progress in the manufacturing process of steelmaking[N]. World Metals, 2014-05-20(B02).
[3]	王新华. 炼钢生产工艺技术进展[N]. 世界金属导报, 2014-05-20(B02).WANG Xin-hua. Progress in the manufacturing process of steelmaking[N]. World Metals, 2014-05-20(B02).
[4]	吴伟, 杨利彬, 郑从杰,等. 转炉熔池传氧速率的冷态模拟研究[C]. 中国金属学会青年学术年会. 2010.WU Wei, YANG Li-bin, ZHENG Cong-jie, et al. Experimental Study on Oxygen Transfer Rate of BOF by Cold Simulation[C]. The Chinese Society For Metals Youth Academic Conference. 2010.
[4]	吴伟, 杨利彬, 郑从杰,等. 转炉熔池传氧速率的冷态模拟研究[C]. 中国金属学会青年学术年会. 2010.WU Wei, YANG Li-bin, ZHENG Cong-jie, et al. Experimental Study on Oxygen Transfer Rate of BOF by Cold Simulation[C]. The Chinese Society For Metals Youth Academic Conference. 2010.
[5]	野崎努. 底吹转炉法—引进?搅拌效果?顶底复合吹炼[M]. 北京: 冶金工业出版社, 2008.野崎努. Bottom Blown Converter—Introduction, Elucidation of Mixing Phenomena and Extensive Development[M]. Beijing: Metallurgical Industry Press, 2008.
[5]	野崎努. 底吹转炉法—引进?搅拌效果?顶底复合吹炼[M]. 北京: 冶金工业出版社, 2008.野崎努. Bottom Blown Converter—Introduction, Elucidation of Mixing Phenomena and Extensive Development[M]. Beijing: Metallurgical Industry Press, 2008.
[6]	2017年高效率低成本转炉炼钢关键技术高级研讨会，2017.04，长沙，中国2017 Advanced Seminar on High Efficiency and Low Cost Converter Steelmaking Key Technology. Changsha, China, 2017.04,.
[6]	2017年高效率低成本转炉炼钢关键技术高级研讨会，2017.04，长沙，中国2017 Advanced Seminar on High Efficiency and Low Cost Converter Steelmaking Key Technology. Changsha, China, 2017.04,.
[7]	Singh V, Sing J, Bhanu C, et al. Optimisation of the bottom tuyeres configuration for the BOF vessel using physical and mathematical modelling[J]. ISIJ international, 2007, 47(11): 1605-1612.
[7]	Singh V, Sing J, Bhanu C, et al. Optimisation of the bottom tuyeres configuration for the BOF vessel using physical and mathematical modelling[J]. ISIJ international, 2007, 47(11): 1605-1612.
[8]	Zhou X, M. Ersson, Zhong L, J?nsson P. A numerical study of mixing behavior in the bath of a converter[C]. Proceedings of the 6th International Congress on the Science and Technology of Steelmaking, Beijing, 2015, 167-170.
[8]	Zhou X, M. Ersson, Zhong L, J?nsson P. A numerical study of mixing behavior in the bath of a converter[C]. Proceedings of the 6th International Congress on the Science and Technology of Steelmaking, Beijing, 2015, 167-170.
[9]	娄文涛, 李勇, 朱苗勇. 顶底复吹转炉内气液两相流行为的数值模拟[J]. 过程工程学报, 2011, 11(6):926-932.LOU Wen-rao, LI Yong, ZHU Miao-yong. Numerical Simulation of Gas-Liquid Two-phase Flow Behacior in the Top and Bottom Combined Blowing Converter[J]. The Chinese Journal of Process Engineering, 2011, 11(6):926-932.
[9]	娄文涛, 李勇, 朱苗勇. 顶底复吹转炉内气液两相流行为的数值模拟[J]. 过程工程学报, 2011, 11(6):926-932.LOU Wen-rao, LI Yong, ZHU Miao-yong. Numerical Simulation of Gas-Liquid Two-phase Flow Behacior in the Top and Bottom Combined Blowing Converter[J]. The Chinese Journal of Process Engineering, 2011, 11(6):926-932.
[10]	崔荣峰, 陈林权. 120t顶底复吹转炉底吹系统的数学模拟和工艺优化[J]. 特殊钢, 2010, 31(3):3-5.CUI Rong-feng, CHEN Lin-quan. Math Simulation and Process Optimization on Bottom-Blowing System of 120t Top and Bottom Combined Blown Converter[J]. Special Steel, 2010, 31(3):3-5.
[10]	崔荣峰, 陈林权. 120t顶底复吹转炉底吹系统的数学模拟和工艺优化[J]. 特殊钢, 2010, 31(3):3-5.CUI Rong-feng, CHEN Lin-quan. Math Simulation and Process Optimization on Bottom-Blowing System of 120t Top and Bottom Combined Blown Converter[J]. Special Steel, 2010, 31(3):3-5.
[11]	温良英, 周远华, 陈登福,等. 复吹转炉熔池内流体流动的数值模拟[J]. 重庆大学学报自然科学版, 2006, 29(1):12-15.WEN Liang-ying, ZHOU Yuan-hua, CHEN Deng-fu, et al. Numerical Simulation of Fluid Flow in Converter Combined Blown Bath[J]. Journal of Chongqing University(Natural Science Edition), 2006, 29(1):12-15.
[11]	温良英, 周远华, 陈登福,等. 复吹转炉熔池内流体流动的数值模拟[J]. 重庆大学学报自然科学版, 2006, 29(1):12-15.WEN Liang-ying, ZHOU Yuan-hua, CHEN Deng-fu, et al. Numerical Simulation of Fluid Flow in Converter Combined Blown Bath[J]. Journal of Chongqing University(Natural Science Edition), 2006, 29(1):12-15.
[12]	张荣生, 陈龙根, 周毅生. 顶底吹冶炼熔池搅拌的水力学研究[J]. 钢铁研究学报, 1983(1).ZHANG Rong-sheng, CHEN Long-gen, ZHOU Yi-sheng. A Hydrodynamic Study on the Stirring Effect in the Too-Bottom Blown bath[J]. Central Iron and Steel Research Institute Technical Bulletin, 1983(1).
[12]	张荣生, 陈龙根, 周毅生. 顶底吹冶炼熔池搅拌的水力学研究[J]. 钢铁研究学报, 1983(1).ZHANG Rong-sheng, CHEN Long-gen, ZHOU Yi-sheng. A Hydrodynamic Study on the Stirring Effect in the Too-Bottom Blown bath[J]. Central Iron and Steel Research Institute Technical Bulletin, 1983(1).
[13]	Nakanishi K, Kato Y, Nozaki T, et al. Cold Model Study on the Mixing Rates of Slag and Metal Bath in Q-BOP[J]. Tetsu- to- Hagane, 1980, 66:1307-1316.
[13]	Nakanishi K, Kato Y, Nozaki T, et al. Cold Model Study on the Mixing Rates of Slag and Metal Bath in Q-BOP[J]. Tetsu- to- Hagane, 1980, 66:1307-1316.
[14]	Paul S, Ghosh D N. Model study of mixing and mass transfer rates of slag-metal in top and bottom blown converters[J]. Metallurgical & Materials Transactions B, 1986, 17(3):461-469.
[14]	Paul S, Ghosh D N. Model study of mixing and mass transfer rates of slag-metal in top and bottom blown converters[J]. Metallurgical & Materials Transactions B, 1986, 17(3):461-469.
[15]	M. J. Luomala, T. M. J. Fabritius, J. J. H?rkki, “The effect of bottom nozzle configuration n the bath behaviour in the BOF”, ISIJ Intern. 44, 5 809-815 (2004).
[15]	M. J. Luomala, T. M. J. Fabritius, J. J. H?rkki, “The effect of bottom nozzle configuration n the bath behaviour in the BOF”, ISIJ Intern. 44, 5 809-815 (2004).
[16]	D N Ghosh, R P Singh. Cold model study of mixing time in hybrid process[J]. Transactionsof the Iron and Steel Institute of Japan, 1988, 28(8): 659-662.
[16]	D N Ghosh, R P Singh. Cold model study of mixing time in hybrid process[J]. Transactionsof the Iron and Steel Institute of Japan, 1988, 28(8): 659-662.
[17]	Choudhary S K, Ajmani S K. Evaluation of bottom stirring system in BOF steelmaking vessel using cold model study and thermodynamic analysis[J]. ISIJ international, 2006, 46(8): 1171-1176.
[17]	Choudhary S K, Ajmani S K. Evaluation of bottom stirring system in BOF steelmaking vessel using cold model study and thermodynamic analysis[J]. ISIJ international, 2006, 46(8): 1171-1176.
[18]	Lai Z, Xie Z, Zhong L. Influence of bottom tuyere configuration on bath stirring in a top and bottom combined blown converter[J]. ISIJ international, 2008, 48(6): 793-798.
[18]	Lai Z, Xie Z, Zhong L. Influence of bottom tuyere configuration on bath stirring in a top and bottom combined blown converter[J]. ISIJ international, 2008, 48(6): 793-798.
[19]	Stisovic T, Koch K. Bottom blowing investigations on a cold model reactor to optimise mixing behaviour in metallurgical processes[J]. Steel research, 2002, 73(9): 373-377.
[19]	Stisovic T, Koch K. Bottom blowing investigations on a cold model reactor to optimise mixing behaviour in metallurgical processes[J]. Steel research, 2002, 73(9): 373-377.