|
|
Kinetics of austenite grain growth in SCr420H steel |
WANG Yang-xin1,2,ZHAO Xiu-ming1,2,MAO Xiang-yang1,2,BU Fan1,2,WANG Wan1,2,AN Jin-min3 |
(1. School of Material Engineering, Nanjing Institute of Technology, Nanjing 211167, Jiangsu, China 2. Jiangsu Key Laboratory of Advanced Structural Materials and Application Technology, Nanjing 211167, Jiangsu, China 3. Special Steel Research and Development Center of Research Institute, Baoshan Iron and Steel Co., Ltd., Shanghai 200940, China) |
|
|
Abstract The crystal growth behavior of SCr420H steel was studied. According to the solid solution formula of the second phase and the maximum the driving force of grain growth,the results were analyzed by the austenite grain size. Therefore,the result of SCr420H steel shows that the second phase particles are gradually reducing and the pinning effect weakly with the increase of holding temperature and the holding time. Grain growth is obvious,and grain size become coarsening gradually. Combined with the actual grain size and principle of Ostwald ripening growth in the second phase,the second phase dissolved less in the insulation 4 h conditions with the temperature rise,and the grain growth rate tends to slow to fast. Under the condition of temperature keeping in 5 and 6 h,the grain size grows steadily with the temperature increasing,and the speed of the growth tends to stop finally. When the holding temperature is above 1 020 ℃,the mixed crystal is more obvious. The initial grain size is 24 μm,and the grain growth of law accordance with Beck equation and Hillert grain growth law. The average activation energy of austenite grain growth is 564.6 kJ/mol.
|
Received: 04 December 2017
Published: 24 July 2018
|
|
|
|
|
[1] |
Yan Y M, Liu Y Z, Zhou L Y, et al.Carburizing law and microstructure of 23CrNi3Mo drill steel[J].Cailiao Kexue Yu Gongyimaterial Science & Technology, 2013, 21(5):102-108
|
[1] |
Yan Y M, Liu Y Z, Zhou L Y, et al.Carburizing law and microstructure of 23CrNi3Mo drill steel[J].Cailiao Kexue Yu Gongyimaterial Science & Technology, 2013, 21(5):102-108
|
[2] |
Kundu A, Davis C L, Strangwood M.Pinning of Austenite Grain Boundaries by Mixed AlN and Nb(C, N) Precipitates[J]. Solid State Phenomena, 2011, 172-174: 458-463.
|
[2] |
Kundu A, Davis C L, Strangwood M.Pinning of Austenite Grain Boundaries by Mixed AlN and Nb(C, N) Precipitates[J]. Solid State Phenomena, 2011, 172-174: 458-463.
|
[3] |
Fang X.Effects of Grain Sizes and Second Phase Sizes of 16MnR Steel on Its Low Temperature Impact Toughness[J].Journal of Mechanical Engineering, 2011, 47(16):40-
|
[3] |
Fang X.Effects of Grain Sizes and Second Phase Sizes of 16MnR Steel on Its Low Temperature Impact Toughness[J].Journal of Mechanical Engineering, 2011, 47(16):40-
|
[4] |
单秀清.SCr420H钢奥氏体混晶问题研究[J]. 理化检验:物理分册, 1997(6):29-31.
|
[4] |
单秀清.SCr420H钢奥氏体混晶问题研究[J]. 理化检验:物理分册, 1997(6):29-31.
|
[5] |
Dan Xiuqing.Study on austenite mixed grain in SCr420H steel [J]. physical and chemical examination: physical science, 1997 (6): 29-31.
|
[5] |
Dan Xiuqing.Study on austenite mixed grain in SCr420H steel [J]. physical and chemical examination: physical science, 1997 (6): 29-31.
|
[6] |
丁志敏, 方建飞, 梁博, 等.微合金化钢奥氏体晶粒长大的动力学[J].材料热处理学报, 2013, 34(s1):88-92
|
[6] |
丁志敏, 方建飞, 梁博, 等.微合金化钢奥氏体晶粒长大的动力学[J].材料热处理学报, 2013, 34(s1):88-92
|
[7] |
Ding Zhimin, Fang Jianfei, Liang Bo, et al.Kinetics of austenite grain growth in V-Nb- (Ti) microalloyed steel[J].Journal of materials and heat treatment, 2013, 34(S1):88-92
|
[7] |
Ding Zhimin, Fang Jianfei, Liang Bo, et al.Kinetics of austenite grain growth in V-Nb- (Ti) microalloyed steel[J].Journal of materials and heat treatment, 2013, 34(S1):88-92
|
[8] |
潘晓刚, 唐荻, 宋勇, 等.级双相钢奥氏体晶粒长大模型[J].北京科技大学学报, 2013, 35(2):189-194
|
[8] |
潘晓刚, 唐荻, 宋勇, 等.级双相钢奥氏体晶粒长大模型[J].北京科技大学学报, 2013, 35(2):189-194
|
[9] |
Pan Xiaogang, Tang Di, Song Yong, et al.DP590 dual phase steel austenite grain growth model[J].Journal of University of Science and Technology Beijing, 2013, 35(2):189-194
|
[9] |
Pan Xiaogang, Tang Di, Song Yong, et al.DP590 dual phase steel austenite grain growth model[J].Journal of University of Science and Technology Beijing, 2013, 35(2):189-194
|
[10] |
余式昌, 吴申庆, 宫友军, 等.气阀钢晶粒长大及其动力学研究[J].钢铁, 2006, 41(6):71-76
|
[10] |
余式昌, 吴申庆, 宫友军, 等.气阀钢晶粒长大及其动力学研究[J].钢铁, 2006, 41(6):71-76
|
[11] |
Yu Shichang, Wu Shenqing, Gong Youjun, et al.Study on grain growth and dynamics of 6Cr21Mn10MoVNbN valve steel[J].iron and steel, 2006, 41(6):71-76
|
[11] |
Yu Shichang, Wu Shenqing, Gong Youjun, et al.Study on grain growth and dynamics of 6Cr21Mn10MoVNbN valve steel[J].iron and steel, 2006, 41(6):71-76
|
[12] |
Sugianto A, Narazaki M, Kogawara M, et al.Numerical simulation and experimental verification of carburizing-quenching process of SCr420H steel helical gear[J].Journal of Materials Processing Technology, 2009, 209(7):3597-3609
|
[12] |
Sugianto A, Narazaki M, Kogawara M, et al.Numerical simulation and experimental verification of carburizing-quenching process of SCr420H steel helical gear[J].Journal of Materials Processing Technology, 2009, 209(7):3597-3609
|
[13] |
Liu H Y, Liang Y C, Jin F F, et al.The research and Practice of reducing X80 pipeline steel mixed crystal structure[C]// asia steel international conference 2012.
|
[13] |
Liu H Y, Liang Y C, Jin F F, et al.The research and Practice of reducing X80 pipeline steel mixed crystal structure[C]// asia steel international conference 2012.
|
[14] |
Koura J, Tamaki M, Aramaki I, et al.Differences in water absorbency of polished rice and elasticity of steamed rice between large and small grains : Studies on the steamed rice in sake brewing (Part 3)[J].Journal of the Brewing Society of Japan, 2016, 105(9):597-603
|
[14] |
Koura J, Tamaki M, Aramaki I, et al.Differences in water absorbency of polished rice and elasticity of steamed rice between large and small grains : Studies on the steamed rice in sake brewing (Part 3)[J].Journal of the Brewing Society of Japan, 2016, 105(9):597-603
|
[15] |
周超, 王毛球, 董瀚, 等.钢奥氏体晶粒长大动力学研究[J].钢铁, 2010, 45(12):73-76
|
[15] |
周超, 王毛球, 董瀚, 等.钢奥氏体晶粒长大动力学研究[J].钢铁, 2010, 45(12):73-76
|
[16] |
Zhou Chao, Wang maoqiu, Dong Han, et al.The austenite grain growth kinetics of 38CrMoAl[J].steel, 2010, 45(12):73-76
|
[16] |
Zhou Chao, Wang maoqiu, Dong Han, et al.The austenite grain growth kinetics of 38CrMoAl[J].steel, 2010, 45(12):73-76
|
[17] |
Narita H, Tanaka M, Morisaku K, et al.Rapid Separation of Palladium(II) from Platinum(IV) in Hydrochloric Acid Solution with Thiodiglycolamide[J].Chemistry Letters, 2004, 33(9):1144-1145
|
[17] |
Narita H, Tanaka M, Morisaku K, et al.Rapid Separation of Palladium(II) from Platinum(IV) in Hydrochloric Acid Solution with Thiodiglycolamide[J].Chemistry Letters, 2004, 33(9):1144-1145
|
[18] |
Yang W, Gao F, Wei G, et al.Ostwald Ripening Growth of Silicon Nitride Nanoplates[J].Crystal Growth & Design, 2010, 10(1):29-31
|
[18] |
Yang W, Gao F, Wei G, et al.Ostwald Ripening Growth of Silicon Nitride Nanoplates[J].Crystal Growth & Design, 2010, 10(1):29-31
|
[19] |
黄顺喆, 厉勇, 王春旭, 等.钢的奥氏体晶粒长大规律研究[J].热加工工艺, 2010, 39(18):31-33
|
[19] |
黄顺喆, 厉勇, 王春旭, 等.钢的奥氏体晶粒长大规律研究[J].热加工工艺, 2010, 39(18):31-33
|
[20] |
Huang Shunzhe, Li Yong, Wang Chunxu, et al.Study on austenite grain growth law of 9310 steel[J].hot working technology, 2010, 39(18):31-33
|
[20] |
Huang Shunzhe, Li Yong, Wang Chunxu, et al.Study on austenite grain growth law of 9310 steel[J].hot working technology, 2010, 39(18):31-33
|
[21] |
Liu G Q, Yu H B, Song X Y, et al.Re-examination and extension of Hillert theory of two-dimensional normal grain growth[J].Medgenmed Medscape General Medicine, 2001, 9(4):632-638
|
[21] |
Liu G Q, Yu H B, Song X Y, et al.Re-examination and extension of Hillert theory of two-dimensional normal grain growth[J].Medgenmed Medscape General Medicine, 2001, 9(4):632-638
|
[22] |
Yang W Q, Min X U, Liang J X, et al.Non-equilibrium grain-boundary segregation of Bi in Cu bicrystals[J].Transactions of Nonferrous Metals Society of China, 2014, 24(12):4038-4043
|
[22] |
Yang W Q, Min X U, Liang J X, et al.Non-equilibrium grain-boundary segregation of Bi in Cu bicrystals[J].Transactions of Nonferrous Metals Society of China, 2014, 24(12):4038-4043
|
[1] |
TIAN Ya-qiang1,BI Wen-qiang1,PAN Hong-bo2,LI Hong-bin1,ZHENG Xiao-ping1,CHEN Lian-sheng1. Effect of carbide evolution on Lüders behavior of cold rolled ART 0.1C-7Mn steel[J]. JOURNAL OF IRON AND STEEL RESEARCH , 2020, 32(6): 505-511. |
[2] |
ZHANG Xin1,LI Sheng-li1,BIAN Shou-yuan1,YAN Ling2. Basic research on hot compression of EH40 ship plate steel[J]. JOURNAL OF IRON AND STEEL RESEARCH , 2020, 32(5): 423-428. |
[3] |
SHAO Cheng-wei, WANG Jun-tao, ZHAO Xiao-li, HUI Wei-jun. Microstructure and mechanical properties of intercritically annealed Al-contain medium Mn steel[J]. Iron and Steel, 2020, 55(5): 87-93. |
[4] |
CAO Yun-fei, YU Wei, LIU Min, JIANG Rui, WANG Chun. Austenite grain growth model of 38MnSiVS bearing microalloyed forging steel[J]. Iron and Steel, 2020, 55(5): 103-108. |
[5] |
CAO Jing-hua1,PAN Hong-bo2,3,ZHANG Jing1,ZHANG Teng-fei2,LI Xu-dong2,LIU Wei-ming2,3. Continuous cooling transformation of NbTi microcarbon deep drawing dualphase steel[J]. JOURNAL OF IRON AND STEEL RESEARCH , 2020, 32(4): 322-328. |
[6] |
DAI Xin-yu, FANG Xu-dong, XU Fang-hong, WEI Ying-hui, HOU Li-feng, DU Hua-yun. Research progress on low cycle fatigue properties of austenitic heat resistant steel[J]. Iron and Steel, 2020, 55(3): 58-67. |
|
|
|
|