基于配合辊系的楔形板矫直工艺

doi:DOI：10.13228/j.boyuan.issn0449-749x.20180299

Abstract
Figure/Table
References (0)
Related Citation (15)

Download: PDF (1549 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract Applying the conventional straightening roller system in straightening the longitude profiled plate will severely reduce the straightening range and efficiency of the longitude profiled plate. In order to improve the thickness range and straightening quality of the longitude profiled plate，a longitude profiled plate straightening method based on a matching roller system method （large diameter straightening roller system and small diameter straightening roller system）was proposed. Firstly，the relationship between the roll diameter and the roll distance of the straightening machine based on the matching roller system was studied. The matching roller system of longitude profiled plate straightening machine was designed，the straightening technology of longitude profiled plate was proposed. Then，the partition principle of the longitude profiled plate with the matching roller straightening machine was studied. The finite element model of longitude profiled plate straightening process based on the matching roller system was established，and the simulation results were consistent with the measured results，which verified the correctness of the finite element model. Finally，the straightening process of the longitude profiled plate based on the matching roller system was simulated. The straightening force and residual stress of the longitude profiled plate under the conventional roller system and the matching roller system were calculated. The influence of different plate thickness partition on the straightening effect of the longitude profiled plate was analyzed. The results show that the designed matching roller system is suitable for the straightening of the longitude profiled plate and the straightening effect is better.

Key words： longitude profiled plate straightening matching roller system partition principle residual stress

Received: 27 July 2018 Published: 25 April 2019

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors

Cite this article:

URL:

http://www.chinamet.cn/Jweb_gt/EN/DOI：10.13228/j.boyuan.issn0449-749x.20180299 OR http://www.chinamet.cn/Jweb_gt/EN/Y2019/V54/I3/47

[1]	Shinichi S, Ryuji M, Tadashi O, et a1. Steel products for shipbuilding. JFE Technical Report.2004, (2): 41-48.
[1]	Shinichi S, Ryuji M, Tadashi O, et a1. Steel products for shipbuilding. JFE Technical Report.2004, (2): 41-48.
[2]	刘向华，刘鑫，付书涛，等.变厚度板带材产品及其深加工[J].轧钢.2015,32(5):1-7.
[2]	刘向华，刘鑫，付书涛，等.变厚度板带材产品及其深加工[J].轧钢.2015,32(5):1-7.
[3]	崔甫. 矫直原理与矫直机械（第2版）[M]. 北京:冶金工业出版社.2008.
[3]	崔甫. 矫直原理与矫直机械（第2版）[M]. 北京:冶金工业出版社.2008.
[4]	连家创. 辊式板带矫直机压下量的计算和设定[J]. 冶金设备.2010,(4):1-4.
[4]	连家创. 辊式板带矫直机压下量的计算和设定[J]. 冶金设备.2010,(4):1-4.
[5]	连家创. 矫直理论与卷取理论[M]. 北京:机械工业出版社.2011.
[5]	连家创. 矫直理论与卷取理论[M]. 北京:机械工业出版社.2011.
[6]	Morris J W, Hardy S J, Lees A W, et al. Formation of residual stresses owing to tension levelling of cold rolled strip[J]. IronMaking and SteelMaking, 2001, 28(1):44-52.
[6]	Morris J W, Hardy S J, Lees A W, et al. Formation of residual stresses owing to tension levelling of cold rolled strip[J]. IronMaking and SteelMaking, 2001, 28(1):44-52.
[7]	Huh H, Lee H W, Park S R, et al. The parametric process design of tension leveling with an elasto.plastic finite element method[J]. Materials Processing Technology. 2001, 113(1): 714-719.
[7]	Huh H, Lee H W, Park S R, et al. The parametric process design of tension leveling with an elasto.plastic finite element method[J]. Materials Processing Technology. 2001, 113(1): 714-719.
[8]	王效岗，黄庆学，马勤，等. 厚板不充分变形矫直工艺方案研究[J]. 塑性工程学报.2008,15(5):191-194.
[8]	王效岗，黄庆学，马勤，等. 厚板不充分变形矫直工艺方案研究[J]. 塑性工程学报.2008,15(5):191-194.
[9]	王勇勤，徐维，严兴春，等. 中厚板横向残余应力控制对策研究[J]. 钢铁.2012,47(4):60-62.
[9]	王勇勤，徐维，严兴春，等. 中厚板横向残余应力控制对策研究[J]. 钢铁.2012,47(4):60-62.
[10]	Fumimaru K, Kazuyki M, Tadashi O, et a1. Steel plates for bridge use and their application technologies[J]. JFE Technical Report, 2004, (2): 85-90.
[10]	Fumimaru K, Kazuyki M, Tadashi O, et a1. Steel plates for bridge use and their application technologies[J]. JFE Technical Report, 2004, (2): 85-90.
[11]	Kleiner M, Kopp R, Homberg W, et al. High-pressure sheet metal forming of tailor rolled blanks[J]. Production Engineering, 2004, 11(2): 109-115.
[11]	Kleiner M, Kopp R, Homberg W, et al. High-pressure sheet metal forming of tailor rolled blanks[J]. Production Engineering, 2004, 11(2): 109-115.
[12]	Ryabkov N, Jackel F, Van Putten K, et al. Production of Blanks with Thickness Transition in Longitudinal and Lateral Direction through 3D-strip Profile Rolling[J]. International Journal of Machine Tools & Manufacture, 2008, 1(1): 391-394.
[12]	Ryabkov N, Jackel F, Van Putten K, et al. Production of Blanks with Thickness Transition in Longitudinal and Lateral Direction through 3D-strip Profile Rolling[J]. International Journal of Machine Tools & Manufacture, 2008, 1(1): 391-394.
[13]	LIU Xiang-hua. Prospects for Variable Gauge Rolling: Technology, Theory and Application[J]. Journal of Iron and Steel Research International, 2011, 18(1): 1-7.
[13]	LIU Xiang-hua. Prospects for Variable Gauge Rolling: Technology, Theory and Application[J]. Journal of Iron and Steel Research International, 2011, 18(1): 1-7.
[14]	杜平，胡贤磊，王君，等.变截面轧制过程的多点动态设定[J].钢铁研究学报.2009,21(11):27-30.
[14]	杜平，胡贤磊，王君，等.变截面轧制过程的多点动态设定[J].钢铁研究学报.2009,21(11):27-30.
[15]	祝夫文，胡贤磊，王市均，等.中厚楔形板轧制的过程控制模型[J].钢铁研究学报.2009,21(7):53-55.
[15]	祝夫文，胡贤磊，王市均，等.中厚楔形板轧制的过程控制模型[J].钢铁研究学报.2009,21(7):53-55.
[16]	高娟.楔形板厚控系统及轧制工艺研究[D].秦皇岛:燕山大学工学硕士学位论文.2008.
[16]	高娟.楔形板厚控系统及轧制工艺研究[D].秦皇岛:燕山大学工学硕士学位论文.2008.
[17]	Cui Li, Shi Quanqiang, Liu Xianghua, et al. Residual Curvature of Longitudinal Profile Plate Roller in Leveling Process. Journal of Iron and Steel Research, 2013, 20(10): 23-27.
[17]	Cui Li, Shi Quanqiang, Liu Xianghua, et al. Residual Curvature of Longitudinal Profile Plate Roller in Leveling Process. Journal of Iron and Steel Research, 2013, 20(10): 23-27.
[18]	王亮亮, 刘长江, 李靖年, 等. LP钢板冷矫直工艺探索[N]. 世界金属导报, 2017-01-24(B07).
[18]	王亮亮, 刘长江, 李靖年, 等. LP钢板冷矫直工艺探索[N]. 世界金属导报, 2017-01-24(B07).
[19]	张子骞，颜云辉,等.一种冷轧差厚板复合矫直辊系装置及柔性矫直方法：中国,CN105344751A[P].2016-02-24.
[19]	张子骞，颜云辉,等.一种冷轧差厚板复合矫直辊系装置及柔性矫直方法：中国,CN105344751A[P].2016-02-24.
[20]	文庆明. 轧钢机械[M]. 北京:化学工业出版社.2004.
[20]	文庆明. 轧钢机械[M]. 北京:化学工业出版社.2004.