含磷高强钢板拉矫破鳞过程的氧化皮剥离机理

doi:10.13228/j.boyuan.issn0449-749x.20200145

Abstract
Figure/Table
References
Related Citation (8)

Download: PDF (4134 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract The bending tests were used to simulate the peeling process of oxide scale on the surface of ultra-low carbon high strength steel sheets containing phosphorus in order to improve its descaling efficiency. The reduction on the middle of the strip was changed in the bending tests in order to study the insertion depth of the bending roll on the withdrawal and straightening leveler. The oxide scale attached to the strip substrate appears as massive exfoliation under the compressive stress,while it mainly shows as crack propagation under the tensile stress condition. An open-source image recognition software,ImageJ,was applied to evaluate the peeling rate and fracturing rate. The results show that the peeling rate of the oxide scale increases with the compressive stress,while the fracturing rate increases with the tensile stress. But both the peeling rate and fracturing rate tend to be a saturation point with the stress increase and the saturation points are quite different. The spalling form of the oxide scale between both strip sides is various due to the existence of residual stress,the different stress state between inner and outer strip surface,and the various material properties of the strip substrate and its oxide scale. The finite element software MARC was conducted to study the effect of insertion depth on the elongation of the withdrawal and straightening leveler. The results from bending tests,microscopic analysis,and simulation conclude that only the elongation cannot fully reflect the descaling effect. The stress state of the oxide scale on the strip surface is also a key factor to evaluate the descaling efficiency.

Key words： descaling peeling rate fracturing rate stress state mechanical simulation

Received: 27 March 2020

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	KONG Ning
	YANG Di
	ZHANG Jie
	LI Hong-bo
	WANG Yi-bo

Cite this article:

KONG Ning,YANG Di,ZHANG Jie等. Oxide scale peeling mechanism of high strength steel sheets containing phosphorus during descaling process[J]. Iron and Steel, 2021, 56(1): 59-68.

URL:

http://www.chinamet.cn/Jweb_gt/EN/10.13228/j.boyuan.issn0449-749x.20200145 OR http://www.chinamet.cn/Jweb_gt/EN/Y2021/V56/I1/59

[1] 胡建军,文杰,于孟,等. DR9镀锡板板形控制技术研究与应用[J]. 中国冶金,2018,28(6):37.(HU Jian-jun,WEN Jie,YU Meng,et al. Research and application of flatness control on DR9 Tinplate[J]. China Metallurgy,2018,28(6):37.)
[2] 韩争攀. X70M管线钢终冷温度偏差大原因分析及工艺改进[J]. 中国冶金, 2019, 29(7): 50.(HAN Zheng-pan. Cause analysis and process improvement of significant finishing temperature deviation of X70M pipeline steel[J]. China Metallurgy, 2019, 29(7): 50.)
[3] LI Tong-qing,CHEN Xian-lin,XU Yao-huan. Research into technology of Bao Steel′s pickling tension leveler[J]. Journal of Iron and Steel Research,International,1997,4(1):26.
[4] 唐伟,杜凤山,文杰,等. 镀锡板翘曲控制策略研究与应用[J]. 钢铁, 2019, 54(12): 55.(TANG Wei, DU Feng-shan, WEN Jie, et al. Research and application of warping control strategy on tinplate[J]. Iron and Steel, 2019, 54(12): 55.)
[5] Le Guevel Y,Grégoire B,Bouchaud B,et al. Influence of the oxide scale features on the electrochemical descaling and stripping of aluminide coatings[J]. Surface and Coatings Technology,2016,292:1.
[6] 林飞,王春峰,李志峰,等. 酸洗工艺对热轧酸洗板表面质量影响机理研究[J]. 轧钢,2019,36(2):11.(LIN Fei, WANG Chun-feng, LI Zhi-feng, et al. Study on the effect mechanism of pickling process on surface quality of hot rolled pickling plate[J]. Steel Rolling, 2019, 36(2): 11.)
[7] 徐言东,顾洋,马树森,等. 几种钢材表面的少酸化除鳞设备[J]. 轧钢,2019,36(4):54.(XU Yan-dong,GU Yang,MA Shu-sen,et al. Introduction of several acid-reducing descaling equipment for steel products[J]. Steel Rolling,2019,36(4):54.)
[8] 辜蕾钢,王业科,刘显军. 热轧带钢深加工工艺装备选型与设计[J]. 轧钢,2019,36(4):49.(GU Lei-gang,WANG Ye-ke,LIU Xian-jun. Technology and equipment design and selection of production line for hot strip subsequent processing[J]. Steel Rolling,2019,36(4):49.)
[9] 卞大鹏,周存龙,李中喜,等. 拉弯矫直机破鳞机理的研究[J]. 机械工程与自动化,2013(6):86.(BIAN Da-peng,ZHOU Cun-long,LI Zhong-xi,et al. Research on the descaling function of tension leveler[J]. Mechanical Engineering and Automation,2013(6):86.)
[10] 叶东东,陈建钧,王忠建. 不同应力状态下带钢的破鳞机理[J]. 钢铁研究学报,2016,28(1):64.(YE Dong-dong,CHEN Jian-jun,WANG Zhong-jian. Spalling mechanisms of oxide scale of strip under different stress states[J]. Journal of Iron and Steel Research,2016,28(1):64.)
[11] 杨子良,王欣,郑涛,等. 拉矫工艺参数对带钢酸洗速率影响的实验研究[J]. 轧钢,2013,30(2):28.(YANG Zi-liang,WANG Xin,ZHENG Tao,et al. Study on effect of stretcher lever parameters on pickling time[J]. Steel Rolling,2013,30(2):28.)
[12] 王建国,李同庆. 拉矫机破鳞原理的研究[J]. 上海金属,1999,21(1):12.(WANG Jian-guo,LI Tong-qing. Research on the descaling function of tension leveler[J]. Shanghai Metals,1999,21(1):12.)
[13] Wadoh S. Steel and characteristics of ferric compound:An experimental study about the cause of work roll wear on the cold reduction of Al-killed CC steel Ⅲ[J]. Tetsu To Hagane-Journal of the Iron and Steel Institute of Japan,1983,69(13):85.
[14] 汤浅博康,吴文章. 酸洗-冷轧生产过程的完全连续化[J]. 本钢译丛,1990(3):1.(Yuasa Beaucamp,Wu Wen-zhang. Complete continuous pickling and cold rolling process[J]. Benxi Steel′s Renditions,1990(3):1.)
[15] Li N,Xiao J,Prud′Homme N,et al. Residual stress study in oxide scale obtained on high temperature oxidation of AISI 430 stainless steel[J]. Advanced Materials Research,2014,996:918.
[16] Lee J M,Noh W,Kim D J,et al. Spallation analysis of oxide scale on low carbon steel[J]. Materials Science and Engineering A,2016,676:385.
[17] Noh W,Lee J M,Kim D J,et al. Effects of the residual stress,interfacial roughness and scale thickness on the spallation of oxide scale grown on hot rolled steel sheet[J]. Materials Science and Engineering A,2019,739:301.
[18] Deng G Y,Tieu A K,Su L H,et al. Microstructural study and residual stress measurement of a hot rolling work roll material during isothermal oxidation[J]. The International Journal of Advanced Manufacturing Technology,2019,102:2107.
[19] 付松岳,任勇,程晓茹,等. 高碳钢盘条三次氧化铁皮机械剥离性能[J]. 钢铁,2016,51(3):73.(FU Song-yue,REN Yong,CHENG Xiao-ru,et al. Descaling property of third oxide scale of high carbon steel wire[J]. Iron and Steel,2016,51(3):73.)
[20] Evans H E. Spallation of oxide from stainless steel AGR nuclear fuel cladding:Mechanisms and consequences[J]. Materials Science and Technology,1988,4(5):414.
[21] 雷明凯,徐忠成,杨辅军,等. 高温合金氧化膜破坏的界面断裂力学分析[J]. 金属学报,2004,40(10):1104.(LEI Ming-kai,XU Zhong-cheng,YANG Fu-jun,et al. Interface fracture mechznics of failure for oxide scale on superalloy[J]. Acta Metallurgica Sinica,2004,40(10):1104.)
[22] Evans H E,Lobb R C. Conditions for the initiation of oxide-scale cracking and spallation[J]. Corrosion Science,1984,24(3):209.
[23] 卞大鹏. Q235氧化铁皮临界断裂应力研究[D]. 太原:太原科技大学,2013.(BIAN Da-peng. Study on Critical Fracture Stress of Q235 Oxide Scale[D]. Taiyuan:University of Science and Technology of Taiyuan,2013.)
[24] Krzyzanowski M,Beynon J H. Finite element model of steel oxide failure during tensile testing under hot rolling conditions[J]. Materials Science and Technology,1999,15(10):1191.
[25] Weibgraeber P,Felger J,Geipel D,et al. Cracks at elliptical holes:Stress intensity factor and finite fracture mechanics solution[J]. European Journal of Mechanics-A/Solids,2016,55:192.
[26] 切列帕诺夫. 脆性断裂力学[M]. 北京:科学出版社,1990.(Cherepanov. Mechanics of Brittle Fracture[M]. Beijing:Science Press,1990.)
[27] Nagl M M,Evans W T. The mechanical failure of oxide scales under tensile or compressive load[J]. Journal of Materials Science,1993,28(23):6247.
[28] Hidaka Y,Anraku T,Otsuka N. Deformation of iron oxides upon tensile tests at 600-1 250 ℃[J]. Oxidation of Metals,2003,59(1):97.
[29] Krzyzanowski M,Yang W,Sellars C M,et al. Analysis of mechanical descaling and modelling approach experimental[J]. Materials Science and Technology,2003,19(1):109.
[30] 陈兵,何名成. 冷轧带钢拉矫机破鳞参数优化与实验研究[C]//第十届中国钢铁年会暨第六届宝钢学术年会论文集.上海:中国金属学会,2015.(CHEN Bing,HE Ming-cheng. Research on parameter optimization and experiment of descaling in tension leveler for cold rolled strips[C]//Proceedings of the 10th CSM Steel Congress and the 6th Baosteel Biennial Academic Conference. Shanghai: The Chinese Society for Metals, 2015.)
[31] 张清东,刘天浩,朱简如. 宽带钢拉伸弯曲矫直变形过程的有限元仿真[J]. 机械工程学报,2008,44(9):236.(ZHANG Qing-dong,LIU Tian-hao,ZHU Jian-ru. Simulation of wide steel strip deformation during tension levelling by finite element method[J]. Chinese Journal of Mechanical Engineering,2008,44(9):236.)
[32] 张清东,周岁,张晓峰,等. 薄带钢拉矫机浪形矫平过程机理建模及有限元验证[J]. 机械工程学报,2015,51(2):49.(ZHANG Qing-dong,ZHOU Sui,ZHANG Xiao-feng, et al. Analytic modeling and corroborating by FEM of tension leveling process of thin buckled steel strip[J]. Chinese Journal of Mechanical Engineering,2015,51(2):49.)