40Cr10Si2Mo钢的热变形模型及动态再结晶行为

doi:10.13228/j.boyuan.issn0449-749x.20210236

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (3567 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract In order to optimize the hot-rolling production process parameters of the martensitic heat-resistant steel 40Cr10Si2Mo and establish digital design and intelligent system database for wire and bar rolling, the constitutive equation of the strain compensation and the dynamic recrystallization behavior of martensitic heat resistant steel 40Cr10Si2Mo at temperatures ranging from 900 to 1 100 ℃ and stain rates from 0.1 to 20 s^-1were studied by single-pass compression tests carried out on Gleeble-3500 thermo-mechanical simulator,which can provide theoretical basis for the plastic deformation behavior and optimizing microstructure of 40Cr10Si2Mo steel. The results show that the stress decreases with the increase of deformation temperature and increases with the increase of strain rate. The effect of temperature and strain rate on thermal deformation resistance (true stress) is mainly determined by the interaction of work hardening, dynamic recovery, recrystallization and other softening mechanisms that occur inside the metal during the plastic deformation process. A constitutive model of Arrhenius was established. The correlation (R²) and the average relative error (AARE) are 0.983 97 and 4.531% respectively between the predicted value of the proposed model and the experimental results. The method of fourth order polynomial fitting and derivation to the σ-ε curves were used to analyse the softening process of 40Cr10Si2Mo steel and the critical conditions of dynamic recrystallization at different deformation conditions. The relationship between the critical condition of dynamic recrystallization and the value of lnZ (Zener-Hollomon parameter) was described. When the lnZ value was less than 63,the critical strain of dynamic recrystallization increased with the increase of the lnZ value. When the lnZ value was greater than 63,the critical strain of dynamic recrystallization did not change significantly with the increase of the lnZ value. Through comparing the microstructure of 40Cr10Si2Mo steel,it was found that the grains swallowed each other and merged, and some of the recrystallized grains did not grow up under the conditions of 1 100 ℃/0.1 s^-1,which eventually led to the appearance of mixed crystal structure. However,increasing the strain rate was beneficial to refine the dynamic recrystallization grains.

Key words： 40Cr10Si2Mo steel constitutive equation dynamic recovery dynamic recrystallization critical strain

Received: 25 April 2021

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	WANG Qing-juan
	WANG Qin-ren
	DU Zhong-ze
	HE Ze-en
	DANG Xue
	QI Ze-jiang

Cite this article:

WANG Qing-juan,WANG Qin-ren,DU Zhong-ze等. Hot deformation model and dynamic recrystallization behavior of 40Cr10Si2Mo steel[J]. Iron and Steel, 2021, 56(11): 112-121.

URL:

http://www.chinamet.cn/Jweb_gt/EN/10.13228/j.boyuan.issn0449-749x.20210236 OR http://www.chinamet.cn/Jweb_gt/EN/Y2021/V56/I11/112

[1] 郭兴伟. 新型马氏体耐热钢的设计与研究[D]. 哈尔滨:哈尔滨工程大学,2012.(GUO Xing-wei. Design and Research of the New Martensitic Heat-Resistance Steel[D]. Harbin:Harbin Engineering University,2012.)
[2] 程世长,刘正东,杨钢,等. 中国内燃机气阀钢的现状和建议[J]. 钢铁研究学报,2005,17(3):1.(CHENG Shi-chang,LIU Zheng-dong,YANG Gang,et al. Production of valve steel for internal combustion engine in China and some suggestions[J]. Journal of Iron and Steel Research,2005,17(3):1.)
[3] 王宇宙,董建新. 汽车发动机用气门材料的选择及研究进展[J]. 材料导报,2016,30(13):87.(WANG Yu-zhou,DONG Jian-xin. Review on the selection and research of valve materials used in automobile engines[J]. Materials Reports,2016,30(13):87.)
[4] 高晓康. 40Cr10Si2Mo气阀钢盘圆生产工艺研究[J]. 特钢技术,2018,24(2):39. (GAO Xiao-kang. Study on production process of valve steel coils 40Cr10Si2Mo[J]. Special Steel Technology,2018,24(2):39.)
[5] 孙增淼,邸永田,姜方,等. 马氏体钢40Cr10Si2Mo线材表面裂纹原因分析和工艺改进[J]. 特殊钢,2020,41(5):22. (SUN Zeng-miao,DI Yong-tian,JIANG Fang,et al. Analysis on surface cracks of martensitic steel 40Cr10Si2Mo wire and process and improvement[J]. Special Steel,2020,41(5):22.)
[6] CAI Z,JI H,PEI W,TANG X,et al. Hot workability,constitutive model and processing map of 3Cr23 Ni8Mn3 N heat resistant steel[J]. Vacuum,2019,165:324.
[7] 赵宏禹,刘荣佩,王长军,等. 9 Ni马氏体不锈钢的热变形行为及其能量耗散图[J]. 钢铁,2018,53(9):74.(ZHAO Hong-yu,LIU Rong-pei,WANG Chang-jun,et al. Hot deformation behavior and energy dissipation diagram of 9 Ni martensite stainless steel[J]. Iron and Steel,2018,53(9):74.)
[8] 胡诗超,张恒华,吴晓春,等. 30Cr3MoV钢热压缩流变应力行为研究[J]. 上海金属,2011,33(3):1. (HU Shi-chao,ZHANG Heng-hua,WU Xiao-chun,et al. Flow stress behavior of 30Cr3MoV steel during hot compression[J]. Shanghai Metals,2011,33(3):1.)
[9] 陈雪娇,王华巍,赵卓,等. Al-Mg-Si合金的高温流变过程动态再结晶研究[J]. 轧钢,2019,36(4):7.(CHEN Xue-jiao,WANG Hua-wei,ZHAO Zhuo,et al. Study on dynamic recrystallization of Al-Mg-Si alloy during high temperature rheological process[J]. Steel Rolling,2019,36(4):7.)
[10] 卫品官,朱松鹤,张恒华,等. 船板钢动态再结晶峰值应力前流变应力曲线模型的研究[J]. 上海金属,2009,31(6):38. (WEI Pin-guan,ZHU Song-he,ZHANG Heng-hua,et al. Study on stress-strain curves of shipbuilding steel before dynamic recrystallization peak stress[J]. Shanghai Metals,2009,31(6):38.)
[11] YANG X,LI W,MA J,et al. Thermo-physical simulation of the compression testing for constitutive modeling of GH4169 superalloy during linear friction welding[J]. Journal of Alloys and Compounds,2016,656:395.
[12] Anbuselvan S,Ramanathan S. Hot deformation and processing maps of extruded ZE41A magnesium alloy[J]. Materials and Design,2010,31(5):2319.
[13] HE D G,LIN Y C,CHEN M S,et al. Effect of pre-treatment on hot deformation behavior and processing map of an aged nickel-based superalloy[J]. Journal of Alloys and Compounds,2015,649:1075.
[14] 康荻娜,庞玉华,罗远,等. F45MnVS钢热变形本构方程[J]. 钢铁,2020,55(9):104.(KANG Di-na,PANG Yu-hua,LUO Yuan,et al. Constitutive equation for hot deformation of F45MnVS steel[J]. Iron and Steel,2020,55(9):104.)
[15] LIN Y C,CHEN X M. A critical review of experimental results and constitutive descriptions for metals and alloys in hot working[J]. Materials and Design,2011,32(4):1733.
[16] Samantaray D,Mandal S,Bhaduri A K. Optimization of hot working parameters for thermo-mechanical processing of modified 9Cr-1Mo (P91) steel employing dynamic materials model[J]. Materials Science and Engineering A,2011,528(15):5204.
[17] LIN Y C,HE D G,CHEN J,et al. Microstructural evolution and support vector regression model for an aged Ni-based superalloy during two-stage hot forming with stepped strain rates[J]. Materials and Design,2018,154:51.
[18] 崔辰硕,高秀华,朱成林,等. 形变热处理对11Cr3Co耐热钢组织性能的影响[J]. 轧钢,2020,37(4):17.(CUI Chen-shuo,GAO Xiu-hua,ZHU Cheng-lin,et al. Effect of thermo-mechanical treatment on microstructure and mechanical properties of 11Cr3Co heat resistant steel[J]. Steel Rolling,2020,37(4):17.)
[19] 吴铁明. 汽轮机用Cr-Mo-V耐热钢的热处理[J]. 上海金属,2018,40(3):27. (WU Tie-ming. Heat treatment of Cr-Mo-V heat resistant steel for steam turbine[J]. Shanghai Metals,2018,40(3):27.)
[20] FAN Q C,JIANG X Q,ZHOU Z H,et al. Constitutive relationship and hot deformation behavior of Armco-type pure iron for a wide range of temperature[J]. Materials and Design,2015,65:193.
[21] LI J R,TIAN H,CHEN L J,et al. Effect of precipitates on the hot embrittlement of 11Cr-3Co-3 W martensitic heat resistant steel for turbine high temperature stage blades in ultra-supercritical power plants[J]. Materials Science and Engineering:A,2019,763.
[22] 张世伟,杨明,梁益龙,等. 20CrNi2Mo钢高温变形的本构方程与动态再结晶行为[J]. 钢铁,2017,52(8):97.(ZHANG Shi-wei,YANG Ming,LIANG Yi-long,et al. Constitutive equations and dynamic recrystallization behaviors of 20CrNi2Mo steel at stage of high temperature deformation[J]. Iron and Steel,2017,52(8):97.)
[23] Poliak E I,Jonas J J. A one-parameter approach to determining the critical conditions for the initiation of dynamic recrystallization[J]. Acta Materialia,1996,44(1):127.
[24] 王忠堂,霍达,于晓林. 基于新加工硬化率方法的AZ80镁合金动态再结晶临界条件[J]. 中国有色金属学报,2018,28(10):30.(WANG Zhong-tang,HUO Da,YU Xiao-lin. Critical conditions of dynamic recrystallization of AZ80 magnesium alloy based on a new method of work hardening rate[J]. The Chinese Journal of Nonferrous Metals,2018,28(10):30.)
[25] TONG Y,QUAN G Z,ZHAO J,et al. Double identification of the optimal hot deformation parameter windows for AlCu4SiMg alloy[J]. Materials Research,2019,22(4):2.
[26] Fang Y Y,Chen X Z,Madigan B,et al. Effects of strain rate on the hot deformation behavior and dynamic recrystallization in China low activation martensitic steel[J]. Fusion Engineering and Design,2016,103:21.
[27] ZHANG W F,LI X L,SHA W,et al. Hot deformation characteristics of a nitride strengthened martensitic heat resistant steel[J]. Materials Science and Engineering:A,2014,590:199.
[28] 王立民,张红,刘宁,等. 高合金马氏体耐热钢的热变形表观激活能[J]. 材料热处理学报,2012,33(2):44. (WANG Li-min,ZHANG Hong,LIU Ning,et al. Apparent activation energy for hot working of high-alloy martensitic heat-resistant steels[J]. Transactions of Materials and Heat Treatment,2012,33(2):44.)
[29] 吕鹏,陈亚楠,关庆丰,等. 新型超超临界机组用叶片钢11Cr12 Ni3Mo2VN的热变形行为[J]. 材料导报,2020,34(4):4113. (LÜ Peng,CHEN Ya-nan,GUAN Qing-feng,et al. The high-temperature deformation behavior of novel 11Cr12 Ni3Mo2VN heat resistant steel for ultra-supercritical units[J]. Materials Reports,2020,34(4):4113.)
[30] Marchattiwar A,Sarkar A. Dynamic recrystallization during hot deformation of 304 austenitic stainless steel[J]. Journal of Materials Engineering and Performance,2013,22(8):2168.
[31] Sellars C M,Whiteman J A. Recrystallization and grain growth in hot rolling[J]. Metal Science,1979,13(3):187.
[32] WANG W,MA R,LI L,et al. Constitutive analysis and dynamic recrystallization behavior of as-cast 40CrNiMo alloy steel during isothermal compression[J]. Journal of Materials Research and Technology,2020,9(2):1929.
[33] Lagneborg R S. A model for hot working occurring by recrystallization[J]. Acta Metallurgica,1975,23:387.
[34] QUAN G Z,AN M,LUO G C,et al. Constitutive modeling for the dynamic recrystallization kinetics of as-extruded 3Cr20 Ni10 W2 heat-resistant alloy based on stress-strain data[J]. Materials and Design,2013,52:98.
[35] 钟茜婷,王磊,刘峰. Incoloy 028合金不连续动态再结晶中链状组织形成机理研究[J]. 金属学报,2018,54(7):969.(ZHONG Xi-ting,WANG Lei,LIU Feng. Study on formation mechanism of necklace structure in discontinuous dynamic recrystallization of Incoloy 028[J]. Acta Metallurgica Sinica,2018,54(7):969.)
[36] Yanushkevich Z,Belyakov A,Kaibyshev R. Microstructural evolution of a 304-type austenitic stainless steel during rolling at temperatures of 773-1 273 K[J]. Acta Materialia,2015,82:244.