浸入式水口倾角对宽幅连铸结晶器内流动行为的影响

doi:10.13228/j.boyuan.issn0449-749x.20210434

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (7164 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract The outlet angle of submerged entry nozzle affects the kinetic energy loss of jet,then affects the flow behavior in the mold. A 1∶4 scale water model of slab mold was built. The influence of 0° and +5° nozzles on the flow behavior in wide slab casting mold was studied using particle image velocimetry under the condition that pulling rate was 0.425 m/min and nozzle immersion depth was 40 mm. The results show that there is a big difference in jet morphology between 0° and +5° nozzle. When the angle is 0°,the jet flow is relatively concentrated and spread slowly,it will spread to the wide surface in the direction of thickness when it reaches the narrow surface. However,at +5°,the jet has a process of upward impact and back again,and the expansion range of jet is larger than that of the 0° nozzle. This will make more jets impact the wide surface before reach the narrow front(which can reach the wide surface within 0.3 s). It means that the molten steel scours dendrite at the front of solidification for wide surface more greatly in actual production,which is not conducive to the growth of slab shell. When the liquid steel flows through +5° nozzle,it first impacts the bottom of nozzle in the direction of gravity,and then returns +5° to shoot from the nozzle. In this process, the kinetic energy loss of liquid steel is greater than 0° nozzle. In addition, the liquid steel flows through a longer distance in the wide-width mold than in the ordinary mold,so the kinetic energy is lost more. This is disadvantageous to the melting of slag and affecting the continuous casting. Comparing the flow fields of the center section,1/4 section and section close to the wide surface under 0° and +5°,the closer to the wide face the velocity of the whole flow field is smaller. At the angle of 0°,the velocity decreases from 0.103 m/s in the central plane to 0.042 m/s in the wide face,and it decreases from 0.097 m/s to 0.066 m/s in the angle of +5°. The symmetrical and asymmetric flow patterns in the mold under 0° and +5° conditions were analyzed. At 0°,86% of the flow states are symmetrical and 14% are asymmetric,while 69% of the flow states are symmetric and 31% are asymmetric at +5°.

Key words： submerged entry nozzle angle fluid flow wide slab continuous casting mold water model

Received: 28 July 2021

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	LIU Wen-xiang
	REN Lei

Cite this article:

LIU Wen-xiang,REN Lei. Influence of outlet angle for submerged entry nozzle on fluid flow in a wide slab casting mold[J]. Iron and Steel, 2022, 57(1): 83-92.

URL:

http://www.chinamet.cn/Jweb_gt/EN/10.13228/j.boyuan.issn0449-749x.20210434 OR http://www.chinamet.cn/Jweb_gt/EN/Y2022/V57/I1/83

[1] 胡群,张硕,王璞,等. 大方坯结晶器内液面波动与卷渣行为[J]. 中国冶金,2020,30(6):63.(HU Qun,ZHANG Shuo,WANG Pu,et al. Liquid level fluctuation and slag entrainment behavior in a bloom mold[J]. China Metallurgy,2020,30(6):63.)
[2] 任磊,张立峰,王强强. 插钉法研究板坯连铸结晶器液面特征[J]. 钢铁,2016,51(2):49.(REN Lei,ZHANG Li-feng,WANG Qiang-qiang. Nail board experiments to investigate level characteristic in slab continuous casting mold[J]. Iron and Steel,2016,51(2):49.)
[3] 王志国,王明林,韦军尤,等. 不同形状板坯结晶器钢液表面流速的物理模拟[J]. 连铸,2021(1):41.(WANG Zhi-guo,WANG Ming-lin,WEI Jun-you,et al. Physical simulation on surface velocity of molten steel in slab molds with different shapes[J]. Continuous Casting,2021(1):41.)
[4] 袁静,时朋召,徐李军,等. 250 mm厚板坯结晶器浸入式水口结构的优化研究[J]. 连铸,2019(4):19.(YUAN Jing,SHI Peng-zhao,XU Li-jun,et al. Optimization of submerged entry nozzle structure for 250 mm thick slab mold[J]. Continuous Casting,2019(4):19.)
[5] 李少翔,杜辰伟,陈培莉,等. 水口结构对超宽板坯连铸结晶器内流场和温度场的影响[J]. 连铸,2015(6):7.(LI Shao-xiang,DU Chen-wei,CHEN Pei-li,et al. Effect of nozzle types on the flow pattern and temperature distribution of the ultra-wide slab continuous casting mold[J]. Continuous Casting,2015(6):7.)
[6] 武鸿杰,徐宇,储成阳,等. 吹气情况下异型坯结晶器水口结构的物理模拟[J]. 连铸,2021(3):45. (WU Hong-jie,XU Yu,CHU Cheng-yang,et al. Physical simulation of nozzle crystallizer nozzle structure under blowing[J]. Continuous Casting,2021(3):45.)
[7] 王瑞,蒋丹青,吴生沪,等. 过热度及结晶器电磁搅拌对连铸坯凝固组织及偏析影响的热模拟研究[J].上海金属,2021,43(2):85.(WANG Rui,JIANG Dan-qing,WU Sheng-hu,et al. Effect of superheat degree and mould electromagnetic stirring onsolidification structure and segregation in continuously cast billet during simulated continuous casting process[J]. Shanghai Metals,2021,43(2):85.)
[8] 牛亮,赵俊学,仇圣桃,等. 水口位置对电磁偏心搅拌作用下大圆坯连铸结晶器内流动及传热的影响[J]. 上海金属,2020,42(5):71.(NIU Liang,ZHAO Jun-xue,QIU Sheng-tao,et al. Effect of superheat degree and mould electromagnetic stirring on solidification structure and segregation in continuously cast billet during simulated continuous casting process[J]. Shanghai Metals,2020,42(5):71.)
[9] 朱苗勇. 高拉速连铸过程传输行为特征及关键技术探析[J]. 钢铁,2021,56(7):1.(ZHU Miao-yong. A study of transport phenomena and key technologies for high-speed continuous casting of steel[J]. Iron and Steel,2021,56(7):1.)
[10] 左小坦,陈永峰,张洪彪,等. 连铸工艺参数对40Cr圆坯碳偏析的影响[J]. 中国冶金,2020,30(6):97.(ZUO Xiao-tan,CHEN Yong-feng,ZHANG Hong-biao,et al. Effect of CC process parameters on carbon segregation of 40Cr round billet[J]. China Metallurgy,2020,30(6):97.)
[11] 袁航,杨树峰,王田田,等. 亚包晶微合金钢连铸板坯角部横裂纹研究进展[J]. 中国冶金,2020,30(10):1.(YUAN Hang,YANG Shu-feng,WANG Tian-tian,et al. Research progress of transverse corner crack on hypo-peritectic micro-alloyed steel slab[J]. China Metallurgy,2020,30(10):1.)
[12] Cho S M,Thomas B G,Kim S H. Effect of nozzle port angle on transient flow and surface slag behavior during continuous steel-slab casting[J]. Metallurgical and Materials Transactions B,2018,50(10):52.
[13] Ismael Calderon Ramos,Rodolfo D Morales,Saul Garcia-Hernandez,et al. Effects of immersion depth on flow turbulence of liquid steel in a slab mold using a nozzle with upward angle rectangular ports[J]. ISIJ International,2014,54(8):1797.
[14] Bai H,Ni P,Ersson M,et al. Effect of swirling flow tundish submerged entry nozzle outlet design on multiphase flow and heat transfer in mould[J]. Ironmaking and Steelmaking,2019,46(9):1.
[15] Teshima T,Kubota J,Suzuki M,et al. Influence of casting conditions on molten steel flow in continuous casting mold at high speed casting of slabs[J]. Tetsu-to-Hagane,1993,79(5):576.
[16] 陈刚,周海龙,喻林,等. 浸入式水口结构对板坯结晶器液面波动的影响[J]. 炼钢,2018,34(5):50.(CHEN Gang,ZHOU Hai-long,YU Lin,et al. Influence of submerged immersion nozzle structure on liquid surface fluctuation in slab continuous-casting mold[J]. Steelmaking,2018,34(5):50.)
[17] 邹涛,战东平,张慧书,等. 板坯连铸结晶器水口优化数理试验研究[J]. 钢铁研究学报,2020,32(4):304.(ZOU Tao,ZHAN Don-ping,ZHANG Hui-shu,et al. Mathematical and physical experimental study on mould nozzle optimization in slab cpntinuous casting[J]. Journal of Iron and Steel Research,2020,32(4):304.)
[18] 张开天,刘建华,崔衡,等. 浸入式水口对结晶器钢水流动与液面波动的影响[J]. 工程科学学报,2018,40(6):697.(ZHANG Kai-tian,LIU Jian-hua,CUI Heng,et al. Effect of SEN on fluid flow and surface fluctuation in a continuous casting slab mold[J]. Chinese Journal of Engineering,2018,40(6):697.)
[19] 熊霄,邓小旋,王新华,等. 水口出口形状对高拉速板坯连铸结晶器内流场特征的影响[J]. 钢铁研究学报,2014,26(7):35.(XIONG Xiao,DENG Xiao-xuan,WANG Xin-hua,et al. Effect of port-shape design on fluid flow in high-speed slab continuous casting mold[J]. Journal of Iron and Steel Research,2014,26(7):35.)
[20] 邓小旋,季晨曦,何文远,等. 板坯连铸结晶器液面的周期性瞬态特征[J]. 钢铁,2017,52(9):42. (DENG Xiao-xuan,JI Chen-xi,HE Wen-yuan,et al. Periodic transient level fluctuations in continuous casting mold of slab[J]. Iron and Steel,2017,52(9):42.)
[21] 黄诚,李晓谦,陈平虎,等. 宽厚板坯连铸结晶器流场、温度场及应力场的耦合数值模拟[J]. 工程科学学报,2016,38(8):1098.(HUANG Cheng,LI Xiao-qian,CHEN Ping-hu,et al. Coupling numerical simulation of flow field,temperature field and stress field in a wide-thick slab continuous casting mold[J]. Chinese Journal of Engineering,2016,38(8):1098.)
[22] Calderon-Ramos I,Morales R D. Influence of turbulent flows in the nozzle on melt flow within a slab mold and stability of the metal-flux interface[J]. Metallurgical and Materials Transactions B,2016,47(3):1866.
[23] Gupta D,Lahiri A K. A water model study of the flow asymmetry inside a continuous slab casting mold[J]. Metallurgical and Materials Transactions B,1996,27(5):757.
[24] 任磊,张立峰,王强强,等. 基于PIV技术的板坯连铸结晶器内钢水流动行为研究[J]. 工程科学学报,2016,38(10):1393.(REN Lei,ZHANG Li-feng,WANG Qiang-qiang,et al. Study on fluid flow in a continuous casting slab mold using particle image velocimetry[J]. Chinese Journal of Engineering,2016,38(10):1393.)
[25] 崔衡,刘洋,李东侠,等. PIV技术在中间包和结晶器流场模拟中的应用[J]. 连铸,2015(3):4.(CUI Heng,LIU Yang,LI Dong-xia,et al. PIV measurement of flow field in physical simulation of slab continuous casting tundish and mold[J]. Continuous Casting,2015(3):4.)