镁处理对1215易切削钢中夹杂物的影响

doi:10.13228/j.boyuan.issn0449-749x.20210787

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (2641 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract Sulfide inclusions in 1215 free-cutting steel not only affect the machinability of steel, but also have a big influence on the anisotropy and the quality of steel. The control of sulfide inclusions is the key to improvement of steel quality. In the current study, Mg treatment was employed to control the morphology, size and distribution of inclusions to explore the effect of Mg on the inclusion modification. Through the high-temperature smelting experiment, a series of steel ingots with different Mg contents were prepared. Using the optical microscope, scanning electron microscope and non-aqueous solution electrolytic etching method, the distribution of inclusions and the two-dimensional as well as the three-dimensional morphology of inclusions in the steel were analyzed. Besides, thermodynamic calculation was conducted to figure out the modification mechanism of inclusions. The results show that, Mg has a strong deoxidation ability, which has a significant influence on the morphology and distribution of sulfide inclusions. When the Mg mass fraction increases from 0 to 0.000 6% and 0.001 7%, the morphology of inclusion changes from spherical, ellipsoidal (type I sulfide) to cluster, chain-like, coralloid (type II sulfide), and then to polyhedron, irregular block (type III sulfide). When the Mg mass fraction further increases to 0.002 7%, the effect of Mg is no more significant. MnS can not be generated in the molten steel. MnS mainly precipitates in the solid-liquid two-phase region during the solidification process, the corresponding precipitation temperature and solidification fraction of steel is 1 502.0 ℃ and 0.409, respectively. During the solidification process, part of MnS takes oxide inclusions as heterogeneous nucleation points, and forms complex inclusion with internal oxide and external sulfide. Once the Mg is added, Al₂O₃ inclusions are modified to dispersive distributed tiny MgO·Al₂O₃ inclusions, which has little possibility of aggregation and growing, providing more heterogeneous nucleation points for the precipitation of MnS. Therefore, the number density of inclusions is increased, while the average equivalent diameter is decreased.

Key words： 1215 free-cutting steel MnS Mg treatment MgO·Al₂O₃

Received: 24 December 2021

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	WANG Pan-feng
	FU Jian-xun
	SHEN Ping

Cite this article:

WANG Pan-feng,FU Jian-xun,SHEN Ping. Effect of magnesium treatment on inclusions in 1215 free-cutting steel[J]. Iron and Steel, 2022, 57(6): 72-81.

URL:

http://www.chinamet.cn/Jweb_gt/EN/10.13228/j.boyuan.issn0449-749x.20210787 OR http://www.chinamet.cn/Jweb_gt/EN/Y2022/V57/I6/72

[1] 王宏斌, 林腾昌, 朱荣, 等. X1215易切削钢连铸坯成分偏析的研究[J]. 北京科技大学学报, 2011, 33(增刊1): 161. (WANG Hong-bin, LIN Teng-chang, ZHU Rong, et al. Study on composition segregation of X1215 free-cutting steel continuous casting billet[J]. Journal of University of Science and Technology Beijing, 2011, 33(s1): 161.)
[2] 王高峰, 李成良, 张志明, 等. 1215MS易切削钢中组织与硫化物分析[J]. 特殊钢, 2020, 41(4): 64. (WANG Gao-feng, LI Cheng-liang, ZHANG Zhi-ming, et al. Analysis on structure and sulfide in 1215MS free cutting steel[J]. Special Steel, 2020, 41(4):64.)
[3] 曹晨巍, 张盼盼, 胡绍晖, 等. 硫系、碲系、铅系易切削钢组织及硫化物对比分析[J]. 冶金分析, 2020, 40(7): 8. (CAO Chen-wei, ZHANG Pan-pan, HU Shao-hui, et al. Structure and sulfide comparative analysis of sulfur, tellurium and lead free-cutting steels[J]. Metallurgical Analysis, 2020, 40(7):8.)
[4] 张盼盼, 胡绍晖, 艾克南, 等. 1215MS钢棒材中硫化物对比分析[J]. 上海金属, 2021, 43(2): 92. (ZHANG Pan-pan, HU Shao-hui, AI Ke-nan, et al. Comparison of sulfide in 1215MS steel bars[J]. Shanghai Metals, 2021, 43(2): 92.)
[5] 沈平, 王冬, 张浩, 等. 碲对硫化物轧制变形行为影响的研究[J]. 钢铁钒钛, 2021, 42(3): 180. (SHEN Ping, WANG Dong, ZHANG Hao, et al. Effect of tellurium on the deformation of sulfides in rolling process[J]. Iron Steel Vanadium Titanium, 2021, 42(3): 180.)
[6] SHEN Ping, ZHANG Dong, ZHANG Hao, et al. Study on the three-dimensional morphology of MnS inclusions in high sulphur steel[J]. Ironmaking and Steelmaking, 2021, 48(10): 1179.
[7] 艾克南, 张盼盼, 赵梦豪, 等. 1215易切削钢拉拔表面裂纹形成机制分析[J]. 钢铁, 2020, 55(2): 88. (AI Ke-nan, ZHANG Pan-pan, ZHAO Meng-hao, et al. Analysis of formation mechanism of surface crack of 1215 free-cutting steel during drawing[J]. Iron and Steel, 2020, 55(2): 88.)
[8] 余国松. 1215MS易切削钢盘条翘皮成因[J]. 中国冶金, 2014, 24(4): 26.(YU Guo-song. Causes of 1215MS free cutting steel wire rode warping[J]. China Metallurgy, 2014, 24(4): 26.)
[9] 谢啸宇, 顾超, 王敏, 等. 中高硫钢中硫化锰夹杂物控制技术[J]. 钢铁, 2021, 56(12): 10. (XIE Xiao-yu, GU Chao, WANG Min, et al. Manganese sulfide inclusion control technology in medium and high sulfur steel[J]. Iron and Steel, 2021, 56(12): 10.)
[10] 孙萌, 姜周华, 李阳, 等. Ce-Mg复合处理对含硫齿轮钢SCr420H洁净度的影响[J]. 钢铁, 2021, 56(7): 47. (SUN Meng, JIANG Zhou-hua, LI Yang, et al. Effect of Ce-Mg treatment on cleanliness of resulfurized gear steel SCr420H[J]. Iron and Steel, 2021, 56(7): 47.)
[11] ZHANG Tong-sheng, WANG De-yong, LIU Chun-wei, et al. Modification of inclusions in liquid iron by Mg treatment[J]. Journal of Iron and Steel Research International, 2014, 21(s1): 99.
[12] ZHANG Tong-sheng, WANG De-yong, JIANG Mao-fa. Effect of magnesium on evolution of oxide and sulphide in liquid iron at 1 873 K[J]. Journal of Iron and Steel Research International, 2014, 21(12): 1073.
[13] 田俊, 王德永, 屈天鹏, 等. 钙、镁在含硫钢中硫化物变性过程中的作用[J]. 钢铁, 2017, 52(11): 27. (TIAN Jun, WANG De-yong, QU Tian-peng, et al. Role and distinction of Ca and Mg to sulfide modification for sulfur steel[J]. Iron and Steel, 2017, 52(11): 27.)
[14] SHEN Ping, FU Jian-xun. Morphology study on inclusion modifications using Mg-Ca treatment in resulfurized special steel[J]. Materials, 2019, 12(2): 197.
[15] SUN Han, WU Liang-ping, XIE Jian-bo, et al. Inclusions modification and improvement of machinability in a non-quenched and tempered steel with Mg treatment[J]. Metallurgical Research and Technology, 2020, 117(2): 208.
[16] 艾克南, 谢剑波, 曾志崎, 等. 镁对非调质钢中组织及硫化物的影响[J]. 钢铁研究学报, 2019, 31(4): 361. (AI Ke-nan, XIE Jian-bo, ZENG Zhi-qi, et al. Effect of Mg on microstructure and sulfide in non-quenched and tempered steel[J]. Journal of Iron and Steel Research, 2019, 31(4): 361.)
[17] 樊田, 杨乾坤, 谢剑波, 等. 镁对20CrMo齿轮钢中夹杂物的影响[J]. 钢铁钒钛, 2019, 40(6): 149. (FAN Tian, YANG Qian-kun, XIE Jian-bo, et al. Effect of Mg on the inclusions in 20CrMo gear steel[J]. Iron Steel Vanadium Titanium, 2019, 40(6): 149.)
[18] 徐龙云, 杨健, 王睿之. Mg脱氧夹杂物对大线能量焊接HAZ组织的影响[J]. 工程科学学报, 2020, 42(增刊1): 9. (XU Long-yun, YANG Jian, WANG Rui-zhi. Influence of inclusions with Mg deoxidation on the microstructure in the heat-affected zone of steel plates after high-heat-input welding[J]. Chinese Journal of Engineering, 2020, 42(s1): 9.)
[19] WU Zhen-hua, WAN Zheng, LI Guang-qiang, et al. Effect of inclusions′ behavior on the microstructure in Al-Ti deoxidized and magnesium-treated steel with different aluminum contents[J]. Metallurgical and Materials Transactions B, 2015, 46(3): 1226.
[20] 陈家祥. 炼钢常用图表数据手册[M]. 北京: 冶金工业出版社, 1984. (CHEN Jia-xiang. Common Chart Sata Manual for Steelmaking[M]. Beijing: Metallurgical Industry Press,1984.)
[21] 李文超. 冶金与材料物理化学[M]. 北京: 冶金工业出版社, 2001. (LI Wen-chao. Physical Chemistry of Metallurgy and Materials[M]. Beijing: Metallurgical Industry Press, 2001.)
[22] 闫卫兵, 林腾昌, 王慧, 等. X1215易切削钢生产工艺实践研究[J]. 工业加热, 2013, 42(5): 35. (YAN Wei-bing, LIN Teng-chang, WANG Hui, et al. Practice research on production technology of X1215 free-cutting steel[J]. Industrial Heating, 2013, 42(5): 35.)
[23] 林腾昌, 朱荣, 姚柳洁, 等. 氧含量、温度与铋对易切削钢中MnS形貌的影响[J]. 工程科学学报, 2018, 40(增刊1): 36. (LIN Teng-chang, ZHU Rong, YAO Liu-jie, et al. Influence of temperature, oxygen, and Bi on the morphology of MnS in free-cutting steel[J]. Chinese Journal of Engineering, 2018, 40(s1): 36.)
[24] Sims C E. The nonmetallic constituents of steel[J]. Transactions of the American Institute of Mining and Metallurgical Engineers, 1959, 215(3): 367.
[25] Ito Yoichi, Masumitsu Noriyuki, Matsubara Kaichi. Formation of manganese sulfide in steel[J]. Transactions of the Iron and Steel Institute of Japan, 1981, 21(7): 477.
[26] Oikawa Katsunari, Ohtani Hiroshi, Ishida Kiyohito, et al. The control of the morphology of MnS inclusions in steel during solidification[J]. ISIJ International, 1995, 35(4): 402.
[27] CHEN Peng-ju, ZHU Cheng-yi, LI Guang-qiang, et al. Effect of sulphur concentration on precipitation behaviors of MnS-containing inclusions in GCr15 bearing steels after LF refining[J]. ISIJ International, 2017, 57(6): 1019.
[28] 蔡开科. 浇注与凝固[M]. 北京: 冶金工业出版社, 1987. (CAI Kai-ke. Casting and Solidification[M]. Beijing: Metallurgical Industry Press, 1987.)
[29] SHEN Ping, ZHANG Li-feng, FU Jian-xun, et al. The effect of Al content on the wettability between liquid iron and MgO·Al₂O₃ binary substrate[J]. Ceramics International, 2019, 45(9): 11287.
[30] Kimura S, Nabeshima Y, Nakajima K, et al. Behavior of nonmetallic inclusions in front of the solid-liquid interface in low-carbon steels[J]. Metallurgical and Materials Transactions B, 2000, 31(5): 1013.
[31] DU Gang, LI Jing, WANG Zhong-bing, et al. Effect of magnesium addition on behavior of collision and agglomeration between solid inclusion particles on H13 steel melts[J]. Steel Research International, 2017, 88(3): 1600185.
[32] Eisenhüttenleute Verein Deutscher. Slag Atlas[M]. D-Düsseldorf: Verlag Stahleisen GmbH, 1995.