高强钢增强韧性的在线淬火技术开发与应用

doi:10.13228/j.boyuan.issn0449-749x.20230198

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (4528 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract In recent years, the online quenching process widely used in the production of high-strength steel for medium and thick plates, which is a green and short process manufacturing process. However, compared with the offline quenching process, the problem of high strength and low impact toughness, which hinders the promotion and application of this process. It is found that the reason for this problem is the austenite grain of the rolled steel plate mainly presents a flat shape due to the improper control of the austenite structure during rolling. In the subsequent direct quenching process, this form of austenite is easy to form martensite lath through the original austenite grain, and the orientation is relatively consistent, which is not conducive to preventing the expansion of cracks. In this paper, based on the control of austenite structure, the rolled steel plate forms fine equiaxed austenite grains, and retains some dislocations during plastic deformation. In the subsequent quenching process, martensite lath with different orientations are formed. This structure is conducive to preventing crack propagation, thus improving the impact toughness of the steel effectively. The production of 550 MPa high strength steel can be achieved without adding expensive microalloying elements, the impact toughness at -20 ℃ has been significantly increased to over 200 J, reaching the equivalent level of offline quenching, while also increasing the production of rolling line. Compared with offline quenching, the microalloyed elements under this process can be more solidly dissolved in austenite, and then retained in martensite during quenching. The precipitation strengthening effect of microalloyed carbonitride is enhanced during tempering. Finally, the 690 MPa high strength steel produced by this process has the same performance and slightly higher strength as offline quenching, which expands a new idea for further promotion the process.

Key words： online quenching austenite control impact toughness high strength steel quenched and tempered steel

Received: 21 April 2023

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	WANG Quanli
	LU Shiping
	MA Longteng
	WANG Kaikai
	DI Guobiao

Cite this article:

WANG Quanli,LU Shiping,MA Longteng等. Development and application of online quenching technology for enhancing toughness of high strength steel[J]. Iron and Steel, 2023, 58(8): 149-156.

URL:

http://www.chinamet.cn/Jweb_gt/EN/10.13228/j.boyuan.issn0449-749x.20230198 OR http://www.chinamet.cn/Jweb_gt/EN/Y2023/V58/I8/149

[1] 崔忠圻,覃耀春. 金属学与热处理[M]. 北京:机械工业出版社,2009.(CUI Z Q,QIN Y C. Metallurgy and Heat Treatment[M]. Beijing:China Machine Press,2009.)
[2] 杨才福,张永权,王瑞珍. 钒钢冶金原理与应用[M]. 北京:机械工业出版社,2012.(YANG C F, ZHAGN Y Q, WANG R Z. Metallurgical Principle and Application of Vanadium Steel[M]. Beijing: Machinery Industry Press, 2012.)
[3] 王国栋.近年我国轧制技术的发展现状和前景[J].轧钢,2017,34(1):1.(WANG G D. Development status and prospects of rolling technology in China in recent years[J]. Rolling Steel, 2017, 34 (1): 1.)
[4] 付天亮, 韩毅, 邓想涛,等. 高等级钢板辊式淬火新技术研发进展与应用[J].轧钢,2022,39(6): 60.(FU T L, HAN Y, DENG X T, et al. Research progress and application of roller quenching technology for high-grade plate[J]. Rolling Steel, 2022,39(6): 60.)
[5] 路士平,王凯凯,王卫华. 60 mm厚Q550D钢板在线淬火韧性提升的研究[J]. 轧钢,2022,39(3):125.(LU S P, WANG K K, WANG W H.Research on toughness improvement of 60 mm thick Q550D steel plate after online quenching[J]. Steel Rolling, 2022, 39 (3):125.)
[6] 王有铭.钢材的控制轧制和控制冷却[M]. 北京:冶金工业出版社,2009.(WANG Y M. Controlled Rolling and Cooling of Steel[M]. Beijing: Metallurgical Industry Press, 2009.)
[7] 余永宁.材料科学基础[M].北京:高等教育出版社,2006.(YU Y N. Fundamentals of Materials Science[M]. Beijing: Higher Education Press, 2006.)
[8] 高为国.ZG230-450钢魏氏组织的微观结构与力学性能[J].金属热处理学报,2003,28(4):39.(GAO W G. Microstructure and mechanical properties of ZG230-450 steel's weinstein structure[J]. Journal of Metal Heat Treatment, 2003, 28 (4): 39.)
[9] CAO J, LIU S, ZHANG J, et al. ASR work roll shifting strategy for schedule-free rolling in hot wide strip mills[J]. Journal of Materials Processing Technology, 2011, 211(11): 1768.
[10] WANG X C, YANG Q, HE A R, et al. Comprehensive contour prediction model of work rolls in hot wide strip mill[J]. Journal of University of Science and Technology Beijing, 2007, 14(3): 240.
[11] CAO J, LIU S, ZHANG J, et al. ASR work roll shifting strategy for schedule-free rolling in hot wide strip mills[J]. Journal of Materials Processing Technology, 2011, 211(11): 1768.
[12] 王立军,武会宾,余伟. 直接淬火低碳贝氏体钢的回火组织与力学性能[J]. 材料工程,2011(3):36.(WANG L J, WU H B, YU W. Tempering structure and mechanical properties of directly quenched low-carbon bainitic steel[J]. Materials Engineering, 2011(3):36.)
[13] 李雪彤,王有铭,徐建国. 高强度厚钢板的调质工艺参数研究[J]. 钢铁,1999,34(1):31.(LI X T, WANG Y M, XU J G. Research on quenching and tempering process parameters of high strength thick steel plates[J]. Iron and Steel, 1999, 34 (1): 31.)
[14] 王国栋. 中国中厚板轧制技术与装备[M].北京:冶金工业出版社,2009.(WANG G D. China Plate Rolling Technology and Equipment[M]. Beijing: Metallurgical Industry Press,2009.)
[15] 段争涛. 热变形及调质工艺对石油储罐用钢组织和力学性能的影响[D]. 沈阳:东北大学,2009.(DUAN Z T. The Influence of Thermal Deformation and Quenching and Tempering Processes on the Microstructure and Mechanical Properties of Steel for Oil Storage Tanks[D]. Shenyang: Northeastern University,2009.)
[16] 段争涛. 高温轧制超快冷工艺在工程机械用钢生产中的应用[J].热加工工艺,2015(5):161.(DUAN Z T. Application of high temperature rolling ultra fast cooling process in the production of steel for construction machinery[J]. Hot Working Process, 2015(5): 161.)
[17] 姚连登,赵四新. 采用在线热处理工艺开发高强钢的研究进展[J].钢铁研究,2011,39(5):54.(YAO L D, ZHAO S X. Research progress on the development of high-strength steel using online heat treatment process[J]. Steel Research, 2011,39(5): 54.)
[18] 李振团,柴锋,杨才福.淬火工艺对铜沉淀强化UHS钢组织性能的影响[J].钢铁,2019,54(6):79.(LI Z T, CHAI F, YANG C F. The effect of quenching process on the microstructure and properties of copper precipitation strengthened UHS steel[J]. Iron and Steel, 2019, 54 (6): 79.)
[19] 牛延龙,刘清友,贾书君.控冷工艺下组织及M/A岛对管线钢韧性的影响[J].钢铁,2020,55(6):96.(NIU Y L, LIU Q Y, JIA S J. The effect of microstructure and M/A island on the toughness of pipeline steel under controlled cooling process[J]. Iron and Steel, 2020, 55 (6): 96.)
[20] LI H J,LI T X,LI R H.Effect of a novel hot-core heavy reduction rolling process after complete solidification on deformation and microstructure of casting steel[J].ISIJ International,2019,59(12):2283.
[21] LI T X,LI H J,LI R H,et al.Work roll surface profile design and optimization for hot-core heavy reduction rolling process[J].ISIJ International,2019,59(7):1314.
[22] WANG B,ZHANG J,XIAO C,et al.Analysis of the evolution behavior of voids during the hot rolling process of medium plates[J]. Journal of Materials Processing Technology,2015,221:121.
[23] 侯东华.600 MPa级在线淬火型高强钢回火显微结构研究[J]. 山东冶金,2018,40(4):27.(HOU D H. Study on the tempering microstructure of 600 MPa online quenched high strength steel[J]. Shandong Metallurgy, 2018, 40 (4): 27.)
[24] 王敬忠,李科元,刘阿娇.40CrNiMo钢国内外研究现状[J].钢铁,2018,53(5):1.(WANG J Z, LI K Y, LIU A J. Research status of 40CrNiMo steel at home and abroad[J]. Iron and Steel, 2018, 53 (5): 1.)
[25] 韩会全,刘彦春,张弛.两相区热处理对不同初始组态钢板组织性能的影响[J].东北大学学报(自然科学版),2008,29(3):339.(HAN H Q, LIU Y C, ZHANG C. The effect of two-phase zone heat treatment on the microstructure and properties of steel plates with different initial configurations[J]. Journal of Northeast University(Natural Science Edition), 2008, 29(3):339.)
[26] 符蓉,王国顺.不同原始组织对20SiMnTi钢亚温淬火力学性能的影响[J].热加工工艺,2002(3):29.(FU R, WANG G S. Effect of different original structures on mechanical properties of 20SiMnTi steel after intercritical quenching[J]. Hot Working Process, 2002 (3): 29.)
[27] 张宽,镇凡,曲锦波.两相区淬火工艺对超高强度钢组织与性能的影响[J].金属热处理,2016,41(10):47.(ZHANG K, ZHEN F,QU J B. Effect of two-phase zone quenching process on the microstructure and properties of ultra-high strength steel[J]. Metal Heat Treatment, 2016, 41(10):47.)
[28] 陈伟,闫强军,张仪杰.高强度工程机械用钢Q960E焊接试验研究[J].宽厚板,2018,24(1):7.(CHEN W, YAN Q J,ZHANG Y J. Experimental study on welding of high strength engineering machinery steel Q960E[J]. Wide and Thick Plate, 2018, 24 (1): 7.)
[29] 张家文,付天亮,吴昊,等.控温淬火工艺对Q960E超高强钢板组织性能的影响[J].材料热处理学报,2021,42(2): 89.(ZHANG J W,FU T L,WU H,et al. The effect of temperature controlled quenching process on the microstructure and properties of Q960E ultra-high strength steel plate[J]. Journal of Materials Heat Treatment, 2021, 42(2):89.)
[30] 其其格,余伟,武会宾.回火工艺对在线淬火12MnNiVR钢组织和性能的影响[J].热加工工艺,2008,37(24):100.(QI Q G, YU W,WU H B. Effect of tempering process on microstructure and properties of online quenched 12MnNiVR steel[J]. Hot Working Process, 2008, 37 (24): 100.)
[31] 邓素怀,王全礼,张慧峰,等. 回火温度对中锰钎杆钢微观组织和力学性能的影响[J]. 中国冶金,2021, 31 (11): 16.(DENG S H, WANG Q L, ZHANG H F, et al. Effect of tempering temperature on microstructure and mechanical properties of medium manganese drill rod steel[J]. China Metallurgy, 2021, 31 (11): 16.)[32] 程巨强,郭金刚.淬火温度对M2AI高速钢组织和硬度的影响[J].铸造技术,2005(9):810.(CHENG J Q,GUO J G. The effect of quenching temperature on the microstructure and hardness of M2AI high-speed steel[J]. Casting Technology, 2005(9): 810.)
[33] 李红英,赖永秋.直接淬火工艺对Q690钢组织和性能的影响[J]. 热加工工艺,2017(6):195.(LI H Y,LAI Y Q.Effect of direct quenching process on microstructure and mechanical properties of Q690 steel[J].Hot Working Technology,2017(6):195.)
[34] 孙畅,李晶,李首慧,等. 淬火工艺对高碳马氏体不锈钢10Cr15MoVCo组织及性能的影响[J]. 中国冶金,2023,33(4): 73.(SUN C, LI J, LI S H, et al. Effect of quenching process on microstructure and properties of 10Cr15MoVCo high-carbon martensitic stainless steel[J]. China Metallurgy, 2023,33(4): 73.)
[35] 梁亮,严立新,邓想涛,等. 淬火工艺对新型耐蚀耐磨钢的组织和性能的影响[J]. 中国冶金,2023,33(5): 9.(LIANG L, YAN L X, DENG X T, et al. Effect of quenching process on microstructure and properties of new corrosion and wear resistant steel[J]. China Metallurgy, 2023,33(5): 9.)
[36] 樊艳秋,马长文,隋鹤龙,等. 模拟焊后热处理对800 MPa级水电用钢组织和性能的影响[J]. 金属热处理,2016,41(6):42.(FAN Y Q,MA C W,SUI H L, et al. Effect of post weld heat treatment on microstructure and properties of 800 MPa grade hydropower steel[J].Heat Treatment of Metals,2016,41(6):42.)
[37] 刘红艳,陈子刚,邓想涛,等. 板带材多功能高精度热处理新技术研发进展[J]. 中国冶金,2023,33(3): 45.(LIU H Y, CHEN Z G, DENG X T, et al. Development of new technologies for multi-function and high-precision heat treatment of plate and strip[J]. China Metallurgy, 2023,33(3): 45.)