|
|
Effect of nozzle position on flow field and solidification in billet mold |
LI Xiaoming, WANG Yang, ZHU Jiayu, YANG Yongkun, WANG Jianli, WANG Weian |
School of Metallurgical Engineering, Xi’an University of Architecture and Technology, Xi’an 710055, Shaanxi, China |
|
|
Abstract Owing to the loss of symmetry in the flow field of the inner and outer arcs when the curved continuous casting nozzle is centered, as well as the uneven temperature of the inner and outer arcs during the production, the solidification quality of the continuous casting billet is seriously affected. Studying the effect of nozzle positioning on improving flow field distribution is particularly crucial. In this study, the mathematical model of electromagnetic, flow, heat transfer and solidification coupling of steel in arc mold is established. The influence of SEN offset direction and offset distance on the flow behavior is studied, and the symmetry index Is is introduced to evaluate the uniformity of solidified shell. It is found that the SEN offset to inner arc increases the flow field difference and produces the bias flow phenomenon, and the application of electromagnetic stirring exacerbates this phenomenon. When the SEN is offset to the outer arc, regardless of whether electromagnetic stirring is applied or not, the index of Is increases and then decreases of each plane, improving the flow field distribution in the mold and make it tend to be symmetrical, which is beneficial to improve the quality of the casting billet. When M-EMS is applied, the vortex core gradually moves to the center of the electromagnetic stirring center surface with the distance of SEN offset to the outer arc increase. Although the steel flow is not symmetrical in the form of inner and outer arcs, there is a certain deflection angle, which increases the temperature difference between the inner and outer arcs in all case models. However, for M-case 6, the temperature difference increases is only 1.666 ℃. When the SEN is offset to the outer arc by 6.5 mm, the index of Is and the uniformity of the solidified shell are the highest, the velocities of the inner and outer arc almost coincide, the temperature difference between the inner and outer arcs is the smallest, the distribution of the steel flow field is the best. By adjusting the position of the SEN, the symmetry of the flow field in the mold can be improved, the uniformity of the solidified shell can be enhanced, and the bias flow phenomenon caused by the mold curvature and the electromagnetic stirring intensification can be eliminated.
|
Received: 18 July 2023
|
|
|
|
[1] KWON S H,WON Y M,BACK G S,et al. Prediction model for degree of solid-shell unevenness during initial solidification in the mold[J]. ISIJ International,2021,61(10):2534. [2] 蔡文菁,杨健. 镁处理对钢中夹杂物以及HAZ组织和性能的影响[J]. 钢铁,2021,56(7):13.(CAI W J,YANG J. Effect of magnesium treatment on inclusions and HAZ microstructure and properties of steel plate[J]. Iron and Steel,2021,56(7):13.) [3] FANG Q,NI H W,ZHANG H,et al. The effects of a submerged entry nozzle on flow and initial solidification in a continuous casting bloom mold with electromagnetic stirring[J]. Metals,2017,7(4):146. [4] ABOUTALEBI M M,LAPOINTE F,D′AMOURS J,et al. Effects of angle of rotation of submerged entry nozzle on fluid flows in a square billet casting mold[J]. Journal of the Minerals, Metals and Materials Society,2018,70(10):2088. [5] BAI H T,NI P Y,ERSSON M,et al. Effect of swirling flow tundish submerged entry nozzle outlet design on multiphase flow and heat transfer in mould[J]. Ironmaking and Steelmaking,2019,46(9):911. [6] 刘文祥,任磊. 浸入式水口倾角对宽幅连铸结晶器内流动行为的影响[J]. 钢铁,2022,57(1):83.(LIU W X,REN L. Influence of outlet angle for submerged entry nozzle onfluid flow in a wide slab casting mold[J]. Iron and Steel,2022,57(1):83.) [7] 张洪才,印传磊,郑力宁,等. 浸入式水口结构对连铸大圆坯质量的影响[J]. 中国冶金,2022,32(9):57.(ZHANG H C,YIN C L,ZHENG L N,et al. Influence of submerged nozzle structure on large sizecontinuous casting round billet quality[J]. China Metallurgy,2022,32(9):57.) [8] GONZALEZ-TREJO J,REAL-RAMIREZ C A,MIRANDA-TELLO J R,et al. Influence of the submerged entry nozzle's bottom well on the characteristics of its exit jets[J]. Metals,2021,11(3):398. [9] CALDERON-RAMOS I,MORALES R D,SERVIN-CASTANEDA R,et al. Modeling study of turbulent flow in a continuous casting slab mold comparing three ports SEN designs[J]. ISIJ International,2019,59(1):76. [10] YOKOYA S,ASAKO Y,HARA S,et al. Control of immersion nozzle outlet flow pattern through the use of swirling flow in continuous casting[J]. ISIJ International,1994,34(11):883. [11] YOKOYA S,TAKAGI S,IGUCHI M,et al. Swirling effect in immersion nozzle on flow and heat transport in billet continuous casting mold[J]. ISIJ International,1998,38(8):827. [12] YOKOYA S,TAKAGI S,IGUCHI M,et al. Swirling flow effect in immersion nozzle on flow in slab continuous casting mold[J]. ISIJ International,2000,40(6):578. [13] WANG Y D,ZHANG L F,YANG W,et al. Effect of nozzle type on fluid flow,solidification,and solute transport in mold with mold electromagnetic stirring[J]. Journal of Iron and Steel Research International,2022,29(2):237. [14] XU P,ZHOU Y Z,CHEN D F,et al. Optimization of submerged entry nozzle parameters for ultra-high casting speed continuous casting mold of billet[J]. Journal of Iron and Steel Research International,2022,29(1):44. [15] NIU L,ZHAO J X,QIU S T. Effects of eccentric mold electromagnetic stirring on continuous casting large steel round blooms:Engineering materials and their applications[J]. Materials Transactions,2020,61(10):2008. [16] WU H J,WEI N,BAO Y P,et al. Effect of M-EMS on the solidification structure of a steel billet[J]. International Journal of Minerals,Metallurgy,and Materials,2011,18(2):159. [17] BARNAMARTIN,MIRKO J,JURGEN R,et al. Simulation of mould level velocities during continuous casting of round bloom strands with mould-electromagnetic stirring[J]. Journal of Iron and Steel Research International,2012(s2):4. [18] 吴春雷,李德伟,朱晓伟,等. 电磁旋流水口连铸技术对小方坯凝固组织形貌和宏观偏析的影响[J]. 金属学报,2019,55(7):875.(WU C L,LI D W,ZHU X W,et al. Influence of electromagnetic swirling flow in nozzle on solidification structure and macrosegregation of continuous casting square billet[J]. Acta Metallurgica Sinica,2019,55(7):875.) [19] 吴春雷,刘晓明,李德伟,等. 电磁旋流水口连铸技术研究进展[J]. 连铸,2022(4):8.(WU C L,LIU X M,LI D W,et al. Study and development on electromagnetic nozzle swirlingflow technology in continuous casting[J]. Continuous Casting,2022(4):8.) [20] 朱晓伟,赵立佳,何明,等. 板坯连铸用电磁旋流水口装置磁场优化设计[J]. 钢铁,2023,58(9):127.(ZHU X W,ZHAO L J,HE M,et al. Magnetic field optimization design of electromagnetic swirlingflow in nozzle device[J]. Iron and Steel,2023,58(9):127.) [21] WU C L,WANG Q,LI D W,et al. Macrosegregation under new flow pattern and temperature distribution induced by electromagnetic swirling flow in nozzle during continuous casting of square billet[J]. Journal of Materials Research and Technology,2020,9(3):5630. [22] LI Y G,SUN Y H,BAI X S. Numerical simulation of flow,heat,solidification,solute transfer and electromagnetic field for vertical mold and curved mold of billet[J]. ISIJ International,2021,61(3):802. [23] REN B Z,CHEN D F,WANG H D,et al. Numerical simulation of fluid flow and solidification in bloom continuous casting mould with electromagnetic stirring[J]. Ironmaking and Steelmaking,2015,42(6):401. [24] WANG J L,QIU G X,ZHU J Y,et al. Effect of nozzle position on fluid flow and solidification in a billet curved mould using mould electromagnetic stirring[J]. Steel Research International,2023,94(3):2200536. [25] 干勇,倪满森,余志祥. 现代连续铸钢实用手册[M]. 北京:冶金工业出版社,2010.(GAN Y,NI M S,YU Z X. Modern Continuous Casting Steel Practical Manual[M]. Beijing:Metallurgical Industry Press,2010.) [26] LI X T,ZHANG Z H,LÜ M,et al. Numerical simulation of the fluid flow,heat transfer,and solidification in ultrahigh speed continuous casting billet mold[J]. Steel Research International,2022,93(6):2100673. [27] DONG Q P,ZHANG J M,YIN Y B,et al. Numerical simulation of macrosegregation in billet continuous casting influenced by electromagnetic stirring[J]. Journal of Iron and Steel Research International,2022,29(4):612. [28] REN B Z,CHEN D F,WANG H D,et al. Numerical analysis of coupled turbulent flow and macroscopic solidification in a round bloom continuous casting mold with electromagnetic stirring[J]. Steel Research International,2015,86(9):1104. [29] YIN S K,LUO S,ZHANG W J,et al. Numerical simulation of macrosegregation in continuously cast gear steel 20CrMnTi with final electromagnetic stirring[J]. Journal of Iron and Steel Research International,2020,28(4):424. [30] CHU R S,LI Z J,FAN Y,et al. Cracking and segregation in high-alloy steel 0.4C1.5Mn2Cr0.35Mo1.5Ni produced by thick continuous casting[J]. Heliyon,2019,5(3):e01329. [31] ZENG J,CHEN W Q,ZHENG H G. Analysis and control of central cracks in the bloom continuous casting of microalloy 49MnVS3 steel[J]. Ironmaking and Steelmaking,2017,44(9):676. [32] 樊东黎,潘健生,徐跃明. 中国材料工程大典第15卷材料热处理工程[M]. 北京:化学工业出版社,2005:217.(FAN D L,PAN J S,XU Y M. Chinese Materials Engineering Dictionary Volume 15 Materials Heat Treatment Engineering[M].Beijing:Chemical Industry Press,2005:217.) [33] ABOUTALEBI M R,HASAN M,GUTHRIE R I L. Coupled turbulent flow,heat,and solute transport in continuous casting processes[J]. Metallurgical and Materials Transactions B,1995,26(4):731. [34] DONG Q P,ZHANG J M,YIN Y B,et al. Three-dimensional numerical modeling of macrosegregation in continuously cast billets[J]. Metals,2017,7(6):209. [35] LI D P,WU H Z,WANG H F,et al.Growth of solidified shell in bloom continuous casting mold of hypo-peritectic steel based on a FeS tracer method[J]. Journal of Iron and Steel Research International,2020,27(7):782. [36] YIN Y B,ZHANG J M,DONG Q P,et al. Modelling on inclusion motion and entrapment during the full solidification in curved billet caster[J]. Metals,2018,8(5):320. [37] SALEEM S,VYNNYCKY M,HASSE F. The Influence of peritectic reaction/transformation on crack susceptibility in the continuous casting of steels[J]. Metallurgical and Materials Transactions B,2017,48(3):1625. [38] MAYER F,WU M H,LUDWIG A. On the formation of centreline segregation in continuous slab casting of steel due to bulging and/or feeding[J]. Steel Research International,2010,81(8):660. |
|
|
|