|
|
Effect of interlayer residual stress on microstructure and properties of sandwich composite plate |
JIN Herong1,2, SHEN Xiaolong3, FENG Kangkang3, ZHANG Biao3, YI Yali3, ZHAO Dingxuan3 |
1. Key Laboratory of Advanced Forging and Stamping Technology and Science of Ministry of National Education, Yanshan University, Qinhuangdao 066004, Hebei, China; 2. Parallel Robot and Mechatronic System Laboratory of Hebei Province, Yanshan University, Qinhuangdao 066004, Hebei, China; 3. School of Mechanical Engineering, Yanshan University, Qinhuangdao 066004, Hebei, China |
|
|
Abstract Adding a filling interlayer between stainless steel composite plates by interlayer vacuum coating technology will produce interlayer residual stress. In the subsequent hot rolling process,the microstructure and mechanical properties of the composite plates may be changed due to the influence of interlayer residual stress. The residual stress between the layers of the stainless steel clad plate is generated by the combined action of the thermal stress and the phase transition stress during the solidification process of the filling interlayer. The residual stress between the layers is eliminated by heat treatment before rolling. The heat treatment process before rolling is formulated by combining numerical simulation and experimental verification. Two kinds of stainless steel clad plates with and without eliminating residual stress between the layers are prepared by interlayer vacuum differential pressure coating,heat treatment before rolling and hot rolling experiments. The effects of residual stress on the microstructure and properties of the clad plate are analyzed by metallographic observation,hardness test,interface energy spectrum scanning,tensile shear and other characterization and performance test experiments. The results show that the rolling pretreatment process to eliminate the residual stress between layers is heating to 400 ℃,holding for 3.5 h and slow cooling under the condition of ensuring the same structure of base layer,interlayer and composite layer. After pre-rolling treatment,the residual stress between layers is reduced by 96.3%. Compared with the composite plate without eliminating interlayer residual stress,the interlayer stress of the composite plate with eliminating interlayer residual stress is significantly enhanced after rolling,and the grain is refined by 81.7%. At the same time,eliminating interlayer residual stress can increase the shear strength of the composite plate by 13.3%,the tensile strength by 3.9%,the elongation after fracture by 4% and the microhardness of the interlayer interface by 3.5%. The research content of this paper improves the overall performance of the sandwich composite plate with filling by eliminating the residual stress between the layers,which can provide theoretical guidance for the improvement of the performance of the related casting forming components,and expand the new idea for the further popularization and application of the process.
|
Received: 08 June 2023
|
|
|
|
[1] 赵云鹏,余超,肖宏,等. 纯铁中间层对热轧不锈钢复合板性能的影响[J]. 钢铁,2020,55(5):73. (ZHAO Y P,YU C,XIAO H,et al. Effect of pure iron interlayer on properties of hot rolled stainless steel clad plate[J]. Iron and Steel,2020,55(5):73.) [2] 金贺荣,孔耀颉,张一,等. 采用铁钴镍合金夹层的316L/EH40复合板界面特征[J]. 钢铁,2020,55(10):63. (JIN H R,KONG Y J,ZHANG Y,et al. Interface characteristics of 316L/EH40 clad plate with Fe-Co-Ni alloy interlayer[J]. Iron and Steel,2020,55(10):63.) [3] 宜亚丽,孔耀颉,王宇韩,等. 涂覆制坯对不锈钢/低合金钢复合界面影响[J]. 钢铁,2021,56(5):105. (YI Y L,KONG Y J,WANG Y H,et al. Effect of coating billet on stainless steel/low alloy steel composite interface[J]. Iron and Steel,2021,56(5):105.) [4] DONG X X,HAMZA Y,ZHANG Y J,et al. High performance Al/TiB2 composites fabricated by nanoparticle reinforcement and cutting-edge super vacuum assisted die casting process[J]. Composites Part B:Engineering,2019,177:107453. [5] CONG X Y,GUANG W Z. The study on TiAl based alloy blade casting structure by bottom pouring vacuum suction casting[J]. Applied Mechanics and Materials,2013,442:44. [6] 宜亚丽,秦越,冯康康,等. 铁钴镍合金配比对层间真空涂覆流动性的影响[J]. 钢铁,2023,58(4):107. (YI Y L,QIN Y,FENG K K,et al. Effect of Fe-Co-Ni alloy ratio on the fluidity of interlayer vacuum coating[J]. Iron and Steel,2023,58(4):107.) [7] SAMAT S,OMAR M Z,BAGHDADI A H,et al. Microstructural evolution,dislocation density and tensile properties of Al-6.5Si-2.1Cu-0.35Mg alloy produced by different casting processes[J]. Journal of Materials Science and Technology,2021,95(36):145. [8] KAUSTUBH R,SWAROOP B,AMIR K,et al. Residual stress,adhesion,hardness,and corrosion resistance of surface alloyed layer formed during sand casting of mild steel[J]. Journal of Materials Engineering and Performance,2022,32(11):4823. [9] YUAN X,ZHANG J,LIAN Y,et al. Research progress of residual stress determination in magnesium alloys[J]. Journal of Magnesium and Alloys,2018,6(3):238. [10] 张根保,张坤能. 残余应力消除技术[J]. 制造技术与机床,2015,634(4):6. (ZHANG G B,ZHANG K N. Residual stress elimination technology[J]. Manufacturing Technology and Machine Tool,2015,634(4):6.) [11] 张益豪,严毅,王振军,等. CF/Al复合材料制备热变形行为与热残余应力分布[J]. 稀有金属材料与工程,2022,51(2):661. (ZHANG Y H,YAN Y,WANG Z J,et al. Hot deformation behavior and thermal residual stress distribution of CF/Al composites[J]. Rare Metal Materials and Engineering,2022,51(2):661.) [12] 沈聪,孔令男,尹臣男,等. 基于Q-P-C-T工艺的NM300耐磨钢组织、综合性能及残余应力调控[J]. 中南大学学报(自然科学版),2022,53(4):1231. (SHEN C,KONG L N,YIN C N,et al. Microstructure,comprehensive properties and residual stress control of NM300 wear-resistant steel based on Q-P-C-T process[J]. Journal of Central South University(Natural Science),2022,53(4):1231.) [13] 姜建堂,范丁歌,赵熊爔,等. 大型铝合金构件制造全过程残余应力预测与控制[J]. 中国材料进展,2022,41(11):899. (JIANG J T,FAN D G,ZHAO X X,et al. Prediction and control of residual stress in the whole manufacturing process of large aluminum alloy components[J]. Materials China,2022,41(11):899.) [14] ZHANG Z H,LIU J H,CHEN J M,et al. Optimization of residual stress in low-pressure casting of ZL205A alloys[J]. Journal of Manufacturing Processes,2023,99:338. [15] 王刚,李俊昊,桑香港,等. 变形对18CrNiMo7-6渗碳钢显微组织与残余应力的影响[J/OL]. 钢铁[2023-07-02]. https://doi.org/10.13228/j.boyuan.issn0449-749x.20230149. (WANG G,LI J H,SANG X G,et al. Effect of deformation on microstructure and residual stress of 18CrNiMo7-6 carburizing steel[J/OL]. Iron and Steel [2023-07-02]. https://doi.org/10.13228/j.boyuan.issn0449-749x.20230149.) [16] 方玉,丁文红,梁亮,等. 冷却模式对NM400相变塑性及残余应力的影响[J]. 钢铁,2023,58(4):116. (FANG Y,DING W H,LIANG L,et al. Effect of cooling mode on transformation plasticity and residual stress of NM400[J]. Iron and Steel,2023,58(4):116.) [17] 蒋文刚,刘其鹏,王振军,等. 纤维体积分数对Cf/Al复合材料热残余应力及损伤影响的数值模拟[J/OL]. 应用力学学报[2023-07-02].http://kns.cnki.net/kcms/detail/61.1112.O3.20230620.1402.002.html. (JIANG W G,LIU Q P,WANG Z J,et al. Numerical simulation of the effect of fiber volume fraction on thermal residual stress and damage of Cf/Al composites[J/OL]. Chinese Journal of Applied Mechanics [2023-07-02]. http://kns.cnki.net/kcms/detail/61.1112.O3.20230620.1402.002.html.) [18] 龚浩,邹鹑鸣,魏尊杰,等. SiC陶瓷/K4169合金复合铸件铸造过程的数值模拟[J]. 稀有金属材料与工程,2022,51(7):2475. (GONG H,ZOU C M,WEI Z J,et al. Numerical simulation of casting process of SiC ceramic/K4169 alloy composite castings[J]. Rare Metal Materials and Engineering,2022,51(7):2475.) [19] 李智锋,汪东红,吴文云,等. 熔模铸造镍基高温合金件热应力场的数值模拟研究[J]. 热加工工艺,2020,49(7):63. (LI Z F,WANG D H,WU W Y,et al. Numerical simulation of thermal stress field of investment casting nickel-based superalloy parts[J]. Hot Working Technology,2020,49(7):63.) [20] 韩云飞,袁兵兵,孙冰,等. 壁厚和铸造缺陷对ZTA15钛合金组织及性能的影响[J]. 钢铁钒钛,2022,43(6):84. (HAN Y F,YUAN B B,SUN B,et al. Effect of wall thickness and casting defects on microstructure and properties of ZTA15 titanium alloy[J]. Iron Steel Vanadium Titanium,2022,43(6):84.) [21] 刘金水,雷衡兵,高文理,等. 铸造残余应力对铝合金副车架疲劳寿命的影响[J]. 湖南大学学报(自然科学版),2018,45(6):28. (LIU J S,LEI H B,GAO W L,et al. Effect of casting residual stress on fatigue life of aluminum alloy subframe[J]. Journal of Hunan University(Natural Sciences),2018,45(6):28.) [22] JAE H Y,ZHI J Z,SON C M,et al. Improvement of structural design accuracy using a casting-structural interface (CSI) method in large-scale sand castings[J]. Journal of Mechanical Science and Technology,2015,29(12):5093. [23] MOHAMED S S,SAMUEL M A,DOTY W H,et al. Relation between residual stresses and microstructure evolution in Al-Si alloys based on different casting parameters[J]. Philosophical Magazine,2019,99(3):284. [24] 毕国永,赵旭一,张路勃. 降低高强度缸盖铸件残余应力的工艺研究[J]. 现代铸铁,2021,41(2):1. (BI G Y,ZHAO X Y,ZHANG L B. Process research on reducing residual stress of high strength cylinder head castings[J]. Modern Cast Iron,2021,41(2):1.) [25] 张新房,向思奇,易坤,等. 脉冲电流调控金属固体中的残余应力[J]. 金属学报,2022,58(5):581. (ZHANG X F,XIANG S Q,YI K,et al. Pulse current regulates residual stress in metal solids[J]. Acta Metallurgica Sinica,2022,58(5):581.) [26] 毛建中,郭灵智,周慧,等. 复合时效消除工件残余应力的工艺研究[J]. 锻压技术,2018,43(10):151. (MAO J Z,GUO L Z,ZHOU H,et al. Study on the process of eliminating residual stress of workpiece by composite aging[J]. Forging and Stamping Technology,2018,43(10):151.) [27] GANG H,BO L. The combined magnetic-vibration stress relief[J]. Results in Physics,2023,47:106372. [28] ZHANG S,RAN Y,MURPHY A,et al. Residual stress analysis of gray cast iron manufacturing processes[J]. Materials and Manufacturing Processes,2022,35(15):1178. [29] RU P L,MOVERARE J,AVDOVIC P,et al. Influence of vibration and heat treatment on residual stress of a machined 12%Cr-steel[J]. Advanced Materials Research,2014,3278(996):609. [30] 韩民峰. 316L/Ni/EH40不锈钢复合板对称热轧成形与热处理工艺研究[D]. 秦皇岛:燕山大学,2020. (HAN M F. Study on Symmetrical Hot Rolling Forming and Heat Treatment Process of 316L/Ni/EH40 Stainless Steel Clad Plate[D]. Qinhuangdao:Yanshan University,2020.) |
[1] |
ZENG Linlin, WANG Cheng, YANG Dapeng, YI Hongliang. Effect of surface decarburization on bending toughness of Al-Si coated hot stamping steel[J]. Iron and Steel, 2023, 58(9): 209-217. |
[2] |
GAO Yongxu1,2, YANG Yuebiao1,3, CHU Xiaohong1,2, DENG Shen3, YE Jiang3, ZHAO Zhengzhi1,2. Effect of annealing process on microstructure and properties of NbTi microalloyed low alloy high strength steel[J]. JOURNAL OF IRON AND STEEL RESEARCH , 2023, 35(4): 454-461. |
[3] |
YANG Jian, LI Ting-ting. Research progress on inclusion control of non-oriented silicon steel with REM treatment[J]. Iron and Steel, 2022, 57(7): 1-15. |
[4] |
ZOU Ying, LIU Hua-sai, HAN Yun, TENG Hua-xiang, JIANG Guang-rui. Research and development progress of hot-rolled galvanized high-strength steel for automobile[J]. Iron and Steel, 2022, 57(12): 118-130. |
[5] |
JIN He-rong, ZHANG Zhao-rui, HAN Min-feng, YI Ya-li, ZHAO Ding-xuan. Effect of nickel interlayer thickness on characteristics of 316L/EH40 composite interface[J]. Iron and Steel, 2021, 56(3): 154-163. |
[6] |
ZHANG Xinyao,ZHA Xiaoqin,REN Yongfeng,ZHANG Wenli,. Microstructure and properties analysis of composite[J]. PHYSICS EXAMINATION AND TESTING, 2021, 39(1): 1-. |
|
|
|
|