固溶温度对Fe-30Mn-8Al-0.8C低密度钢组织及力学性能的影响

doi:10.13228/j.boyuan.issn0449-749x.20230366

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (0 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract To study the microstructure evolution and mechanical properties of Fe-30Mn-8Al-0.8C(wt.%) low density steel treated at different solid solution temperatures varying from 900 ℃ to 1 100 ℃,the growth behavior of austenite grains was analyzed using OM,EBSD and XRD. Sallars model was adopted to fit the austenite grain size after solution treatments with different temperatures and time. The growth model of austenite grains was established. Tensile tester and hardness tester were used to test the mechanical properties of the experimental steel. The relationship between the microstructure and mechanical properties of the experimental steel was analyzed based on the results of tensile tests and hardness measurements. The results show that the microstructure of experimental steel was austenite with undissolved κ-carbides after solid solution treatment at 900 ℃ for 90 min,which became fully austenitic after solid solution treatment at other temperatures. The austenite grain size increased with solid solution temperature. The austenite grain growth behavior was fitted and analyzed to give a model for the relationship among solid solution temperature,holding time and austenite grain size. The elongation,yield strength and tensile strength decreased gradually with increasing solid solution temperature. Due to the presence of incompletely solidified κ-carbides in the 900 ℃ specimens,which led to early fracture of the specimens,the elongation of the specimens solution-treated at 900 ℃ was slightly lower than that of the 950 ℃ specimens. The optimum strength and plasticity combination of the experimental steel was obtained after solution treatment at 950 ℃ for 90 min. The product of strength and elongation reached 44.3 GPa·%. As the solid solution temperature increased,the work-hardening rate decreased,resulting in a lower work-hardening term for the tensile strength. According to the Hall-Petch relationship,the equation for the relationship between yield strength and grain size of the experimental steel was given. The mechanical properties of as-solid-solution Fe-30Mn-8Al-0.8C austenitic low-density steels with high-Mn and high-Al concentration can be predicted by considering the growth model of austenite grain.

Key words： low density steel solid solution treatment austenite grain growth mechanical property

Received: 29 June 2023

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	ZHANG Qi
	SHEN Yiping
	CHEN Guanghui
	XUE Zhengliang
	XU Guang

Cite this article:

ZHANG Qi,SHEN Yiping,CHEN Guanghui等. Effect of solid solution temperature on microstructures and mechanical properties of Fe-30Mn-8Al-0.8C low density steel[J]. Iron and Steel, 2024, 59(2): 129-138.

URL:

http://www.chinamet.cn/Jweb_gt/EN/10.13228/j.boyuan.issn0449-749x.20230366 OR http://www.chinamet.cn/Jweb_gt/EN/Y2024/V59/I2/129

[1] ZHANG W,XU J. Advanced lightweight materials for Automobiles:A review[J]. Materials and Design,2022,221:110994.
[2] 赵征志,陈伟健,高鹏飞,等. 先进高强度汽车用钢研究进展及展望[J]. 钢铁研究学报,2020,32(12):1059. (ZHAO Z Z,CHEN W J,GAO P F,et al. Progress and perspective of advanced high strength automotive steel[J]. Journal of Iron and Steel Research,2020,32(12):1059.)
[3] 刘春泉,彭其春,薛正良,等. Fe-Mn-Al-C系列低密度高强钢的研究现状[J]. 材料导报,2019,33(15):2572.(LIU C C,PENG Q C,XUE Z L,et al. Research situation of Fe-Mn-Al-C system low-density high-strength steel[J]. Materials Reports,2019,33(15):2572.)
[4] 满廷慧,彭伟,王子波,等. Fe-Mn-Al-C低密度钢研究现状及展望[J]. 中国冶金,2022,32(1):11.(MAN T H,PENG W,WANG Z B,et al. Research progress and prospect of Fe-Mn-Al-C low-density steels[J]. China Metallurgy,2022,32(1):11.)
[5] 王伟胜,朱航宇,宋明明,等. Fe-23Mn-xAl-0.7C低密度钢中非金属夹杂物形成机理[J]. 钢铁,2020,55(10):29.(WANG W S,ZHU H Y,SONG M M,et al. Formation mechanism of non-metallic inclusions in Fe-23Mn-xAl-0.7C lightweight steels[J]. Iron and Steel,2020,55(10):29.)
[6] 王蓝卿,朱航宇,赵吉轩,等. MgO与低密度钢液相互作用及其对夹杂物的影响[J]. 钢铁,2021,56(10):83. (WANG L Q,ZHU H Y,ZHAO J X,et al. Interaction between MgO and low-density molten steel a and its influence on inclusions[J]. Iron and Steel,2021,56(10):83.)
[7] 邢梅,林方敏,唐立志,等. Al元素对Fe-Mn-Al-C系低密度钢的影响特性综述[J]. 中国冶金,2022,32(2):15. (XING M,LIN F M,TANG L Z,et al. Effect of Al on properties of Fe-Mn-Al-C low density steel[J]. China Metallurgy,2022,32(2):15.)
[8] 王瑞,张丽凤,王社则,等. 低密度汽车钢的显微组织与氢脆性能[J]. 上海金属,2020,42(4):6. (WANG R,ZHANG L F,WANG S Z,et al. Microstructure and hydrogen embrittlement properties of low density automotive steel[J]. Shanghai Metals,2020,42(4):6.)
[9] CHEN S,RANA R,HALDAR A,et al. Current state of Fe-Mn-Al-C low density steels[J]. Progress in materials science,2017,89:345.
[10] DING H,LIU D,CAI M,et al. Austenite-based Fe-Mn-Al-C lightweight steels:Research and prospective[J]. Metals,2022,12(10):1572.
[11] ZUAZO I,HALLSTEDT B,LINDAHL B,et al. Low-density steels:Complex metallurgy for automotive applications[J]. JOM,2014,66(9):1747.
[12] 王凤权,孙挺,王毛球,等. Fe-Mn-Al-C系奥氏体基低密度钢的研究进展[J]. 钢铁,2021,56(6):89. (WANG F Q,SUN T,WANG M Q,et al. Research progress of Fe-Mn-Al-C system austenitic low density steel[J]. Iron and Steel,2021,56(6):89.)
[13] 宋宏伟,李慧蓉,高建新,等. 合金元素对Fe-Mn-Al-C系轻质钢组织和性能影响的研究现状[J]. 热加工工艺,2019,48(6):19. (SONG H W,LI H R,GAO J X,et al. Research status on effect of alloying elements on microstructure and properties of F -Mn-Al-C Based lightweight steel[J]. Hot Working Technology,2019,48(6):19.)
[14] 胡光立,谢希文. 钢的热处理(原理和工艺)[M]. 西安:西北工业大学出版社,2010.(HU G L,XIE X W. Heat Treatment of Steel (Principles and Processes)[M]:Xi’an:Northwestern Polytechnic University Press,2010.)
[15] BALIGIDAD R G,PRASAD K S. Effect of Al and C on structure and mechanical properties of Fe-Al-C alloys[J]. Materials Science and Technology,2013,23(1):38.
[16] 徐越鹏. 热处理对汽车用高强低密度钢组织及性能的影响[D]. 重庆:重庆大学,2017.(XU Y P. Effect of Heat Treatment on the Microstructure and Properties of Automobile High-strength Low-density Steel[D]. Chongqing:Chongqing University,2017.)
[17] FIELD D M,LIMMER K R,HORNBUCKLE B C. On the grain growth kinetics of a low density steel[J]. Metals,2019,9(9):997.
[18] 刘少尊,厉勇,王春旭,等. 固溶处理对Fe-Mn-Al-C系低密度钢组织与性能的影响[J]. 金属热处理,2015,40(9):120.(LIU S Z,LI Y,WANG C X,et al. Effects of solution treatment on microstructures and properties of Fe-Mn-AI-C low density steel[J]. Heat Treatment of Metals,2015,40(9):120.)
[19] 付锡彬,孟少博,刘文胜,等. 固溶处理对Fe-30Mn-10Al-1C低密度钢组织及力学性能的影响[J]. 金属热处理,2022,47(7):114.(FU X B,MENG S B,LIU W S,et al. Effect of solution treatment on microstructure and mechanical properties of Fe-30Mn-10A1-1C low density steel[J]. Heat Treatment of Metals,2022,47(7):114.)
[20] 张琪,王厚昕,朱敏,等. Nb微合金化高碳钢奥氏体晶粒长大原位观察[J]. 钢铁研究学报,2022,34(8):840. (ZAHNG Q,WANG H X,ZHU M,et al. In situ observation on austenite grain growth of a Nb microalloyed high carbon steel[J]. Journal of Iron and Steel Research,2022,34(8):840.)
[21] LI C,MA B,SONG Y,et al. The annealing twins of Fe-20Mn-4Al-0.3C austenitic steels during symmetric and asymmetric hot rolling[J]. Metals,2018,8(11):882.
[22] JEONG J,LEE C,PARK I,et al. Isothermal precipitation behavior of κ-carbide in the Fe-9Mn-6Al-0.15C lightweight steel with a multiphase microstructure[J]. Journal of Alloys and Compounds,2013,574:299.
[23] RANDLE V,RIOS P R,HU Y. Grain growth and twinning in nickel[J]. Scripta Materialia,2008,58(2):130.
[24] 李志刚. 一种镍铁基变形高温合金中退火孪晶界的演变与力学行为[D]. 上海:上海交通大学,2015. (LI Z G. Evolution of Annealing Twin Boundary and Mechanical Behavior in a Nickel-Iron Based Wrought Alloy[D]. Shanghai:Shanghai Jiao Tong University,2015.)
[25] DASARI S,SARKAR A,SHARMA A,et al. Recovery of cold-worked Al0.3CoCrFeNi complex concentrated alloy through twinning assisted B2 precipitation[J]. Acta Materialia,2021,202:448.
[26] CHEN X M,LIN Y C,WU F. EBSD study of grain growth behavior and annealing twin evolution after full recrystallization in a nickel-based superalloy[J]. Journal of Alloys and Compounds,2017,724:198.
[27] 张维娜,刘振宇,王国栋. 高锰TWIP/TRIP钢研究进展与应用[J]. 中国工程科学,2014,16(1):40.(ZHANG W,LIU Z,WANG G D,et al. State of the art for research,development and applications of high manganese TWIP/TRIP steel[J]. Strategic Study of CAE,2014,16(1):40.)
[28] GUO Z,HU F,WANG Z,et al. Study on as-cast microstructure of Fe-15Mn-10Al-5Ni-0.8C low density duplex steel[J]. Materials Research Express,2022,9(2):026512.
[29] DONG D,CHEN F,CUI Z. Modeling of austenite grain growth during austenitization in a low alloy steel[J]. Journal of Materials Engineering and Performance,2016,25(1):152.
[30] 韩汝洋,杨庚蔚,孙新军,等. 钒微合金化中锰马氏体耐磨钢奥氏体晶粒长大行为[J]. 金属学报,2022,58(12):1589. (HAN R,YANG G,SUN X,et al. Austenite grain growth behavior of vanadium microalloying medium manganese martensitic wear-resistant steel[J]. Acta Metallurgica Sinica,2022,58(12):1589.)
[31] UHM S,MOON J,LEE C,et al. Prediction model for the austenite grain size in the coarse grained heat affected zone of Fe-C-Mn steels:Considering the effect of initial grain size on isothermal growth behavior[J]. ISIJ International,2004,44(7):1230.
[32] QIU C,ZUROB H S,PANAHI D,et al. Quantifying the solute drag effect on ferrite growth in Fe-C-X Alloys using controlled decarburization experiments[J]. Metallurgical and Materials Transactions A,2013,44(8):3472.
[33] 付立铭,单爱党,王巍. 低碳Nb微合金钢中Nb溶质拖曳和析出相NbC钉扎对再结晶晶粒长大的影响[J]. 金属学报,2010,46(7):832.(FU L,SHAN A,WANG W. Effect of Nb solute drag and NbC precipitate pinning on the recrystallization grain growth in low carbon Nb-microalloyed steel[J]. Acta Metallurgica Sinica,2010,46(7):832.)
[34] FAZELI F,MILITZER M. Application of solute drag theory to model ferrite formation in multiphase steels[J]. Metallurgical and Materials Transactions A,2005,36(6):1395.
[35] DILLON S. An experimentally quantifiable solute drag factor[J]. Acta Materialia,2008,56(6):1374.
[36] 杨清,张立文,张驰,等. 低碳Nb-V-Ti微合金钢X70的奥氏体晶粒长大行为[J]. 金属热处理,2019,44(4):1.(YANG Q,ZHANG L,ZHANG C,et al. Austenite grain growth behavior of low carbon Nb-V-Ti microalloyed steel X70[J]. Heat Treatment of Metals,2019,44(4):1.)
[37] XU D,JI C,ZHAO H,et al. A new study on the growth behavior of austenite grains during heating processes[J]. Scientific reports,2017,7(1):3968.
[38] MOCHTAR M A,FATRIANSYAH J F,SUHARIADI I,et al. Numerical prediction of austenite grain growth characteristic of AISI O1 alloy steel[J]. Journal of Materials Engineering and Performance,2023,32:3322.
[39] 孙建,黄贞益,李景辉,等. 固溶和时效处理对Fe-Mn-Al-C轻质钢组织和硬度的影响[J]. 金属热处理,2022,47(3):34.(SUN J,HUANG Z Y,LI J H,et al. Effect of solution treatment and aging on microstructure and hardness of Fe-Mn-Al-C light weight steel[J]. Heat Treatment of Metals,2022,47(3):34.)
[40] GUAN J,WANG L,ZHANG Z,et al. Fatigue crack nucleation and propagation at clustered metallic carbides in M50 bearing steel[J]. Tribology International,2018,119:165.
[41] 张晨,胡锋,周杰,等. κ-碳化物对低密度超细珠光体组织细化的影响[J]. 中国冶金,2023,33(5):60. (ZHANG C,HU F,ZHOU J,et al. Effect of κ-carbide on microstructure refinement of ultra fine pearlite in low density steel[J]. China Metallurgy,2023,33(5):60.)
[42] 杨富强,宋仁伯,孙挺,等. Fe-Mn-Al轻质高强钢组织和力学性能研究[J]. 金属学报,2014,50(8):897. (YANG F Q,SONG R B,SUN T,et al. Microstructure and mechanical properties of Fe-Mn-Al light-weight high strength steel[J]. Acta Metallurgica Sinica,2014,50(8):897.)
[43] 孙健瑀. 奥氏体高锰钢组织及力学性能研究[D]. 沈阳:东北大学,2015. (SUN J Y. Study on Microstructure and Mechanical Properties of Austenite High Manganese Steels[D]. Shenyang:Northeastern University,2015.)
[44] SINGH K K,SANGAL S,MURTY G S. Hall-Petch behaviour of 316L austenitic stainless steel at elevated temperatures[J]. Materials Science and Technology,2002,18(10):1168.
[45] PARK S J,KIM K S,KANG J H,et al. Effects of carbon and nitrogen on Hall-Petch relationship in austenitic stainless steel[J]. Journal of Materials Research and Technology,2022,19:2960.
[46] 沈逸平,张琪,陈光辉,等. Fe-30Mn-8Al-0.8C奥氏体低密度钢变形中组织演变及变形机制[J]. 钢铁,2023,58(3):135. (SHEN Y P,ZHANG Q,CHEN G H,et al. Microstructure evolution and deformation mechanism of Fe-30Mn-8Al-0.8C austenitic low density steel during deformation[J]. Iron and Steel,2023,58(3):135.)
[47] KUHLMANN WILSDORF D,WILSDORF H G F,WERT J A. LEDS theory of workhardening stages and "planar" versus "distributed" glide[J]. Scripta Metallurgica et Materialia,1994,31(6):729.
[48] FEAUGAS X. On the origin of the tensile flow stress in the stainless steel AISI 316L at 300 K:Back stress and effective stress[J]. Acta Materialia,1999,47(13):3617.