Effect of Cooling Method on Microstructure and Mechanical Properties of Hot-Rolled C-Si-Mn TRIP Steel
LIU Ji-yuan1,ZHANG Zi-cheng2,ZHU Fu-xian1,LI Yan-mei1,Manabe Ken-ichi2
1. State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110004, Liaoning, China 2. Department of Mechanical Engineering, Tokyo Metropolitan University, Tokyo 192-0397, Japan
Effect of Cooling Method on Microstructure and Mechanical Properties of Hot-Rolled C-Si-Mn TRIP Steel
LIU Ji-yuan1,ZHANG Zi-cheng2,ZHU Fu-xian1,LI Yan-mei1,Manabe Ken-ichi2
1. State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110004, Liaoning, China 2. Department of Mechanical Engineering, Tokyo Metropolitan University, Tokyo 192-0397, Japan
ժҪ The controlled cooling technology following hot rolling process is a vital factor that affects the final microstructure and mechanical properties of the hot-rolled transformation induced plasticity (TRIP) steels. In the present study, low alloy C-Si-Mn TRIP steel was successfully fabricated by hot rolling process with a �p450 hot rolling mill. To maximize the volume fraction and stability of retained austenite of the steel, two different cooling methods (air-cooling and ultra-fast cooling ��AC-UFC�� and ultra-fast cooling, air-cooling and ultra-fast cooling ��UFC-AC-UFC��) were conducted. The effects of the cooling method on the microstructure of hot-rolled TRIP steel were investigated via optical microscope, transmission electron microscope and conversion electron M��ssbauer spectroscope. The mechanical properties of the steel were also evaluated by conventional tensile test. The results indicated that ferrite and bainite in the microstructure were refined with the cooling method of UFC-AC-UFC. The morphology of retained austenite was also changed from small islands distributing in bainite district (obtained with AC-UFC) to granular shape locating at the triple junction of the ferrite grain boundaries (obtained with UFC-AC-UFC). As a result, the TRIP steel with a content of retained austenite of 11��52%, total elongation of 32% and product of tensile strength and total elongation of 27552 MPa��% was obtained.
Abstract��The controlled cooling technology following hot rolling process is a vital factor that affects the final microstructure and mechanical properties of the hot-rolled transformation induced plasticity (TRIP) steels. In the present study, low alloy C-Si-Mn TRIP steel was successfully fabricated by hot rolling process with a �p450 hot rolling mill. To maximize the volume fraction and stability of retained austenite of the steel, two different cooling methods (air-cooling and ultra-fast cooling ��AC-UFC�� and ultra-fast cooling, air-cooling and ultra-fast cooling ��UFC-AC-UFC��) were conducted. The effects of the cooling method on the microstructure of hot-rolled TRIP steel were investigated via optical microscope, transmission electron microscope and conversion electron M��ssbauer spectroscope. The mechanical properties of the steel were also evaluated by conventional tensile test. The results indicated that ferrite and bainite in the microstructure were refined with the cooling method of UFC-AC-UFC. The morphology of retained austenite was also changed from small islands distributing in bainite district (obtained with AC-UFC) to granular shape locating at the triple junction of the ferrite grain boundaries (obtained with UFC-AC-UFC). As a result, the TRIP steel with a content of retained austenite of 11��52%, total elongation of 32% and product of tensile strength and total elongation of 27552 MPa��% was obtained.
LIU Ji-yuan,ZHANG Zi-cheng,ZHU Fu-xian,LI Yan-mei,Manabe Ken-ichi. Effect of Cooling Method on Microstructure and Mechanical Properties of Hot-Rolled C-Si-Mn TRIP Steel[J]. �й������ڿ���, 2012, 19(1): 41-46.
LIU Ji-yuan,ZHANG Zi-cheng,ZHU Fu-xian,LI Yan-mei,Manabe Ken-ichi. Effect of Cooling Method on Microstructure and Mechanical Properties of Hot-Rolled C-Si-Mn TRIP Steel. Chinese Journal of Iron and Steel, 2012, 19(1): 41-46.
2012, Vol. 19 
