1 Heavy Machinery Engineering Research Center of Ministry of Education, Taiyuan University of Science and Technology, Taiyuan 030024, Shanxi, China 2 Shanxi Provincial Key Laboratory of Metallurgical Device Design Theory and Technology, Taiyuan University of Science and Technology, Taiyuan 030024, Shanxi, China
Numerical model establishment and verification of cold pilgering on cycle feed rate
1 Heavy Machinery Engineering Research Center of Ministry of Education, Taiyuan University of Science and Technology, Taiyuan 030024, Shanxi, China 2 Shanxi Provincial Key Laboratory of Metallurgical Device Design Theory and Technology, Taiyuan University of Science and Technology, Taiyuan 030024, Shanxi, China
ժҪ A numerical model was established to calculate the cycle feed rate through studying the case of a cold pilger mill with the 304 stainless steel pipe. Firstly, the precise constitutive equation of 304 stainless steel was obtained through nonlinearly fitting the true stress�Cstrain data from unidirectional tensile test. Then, the numerical method to calculate the equivalent deformation was determined according to the plastic deformation feature of the steel tube during cold rolling and the incremental theory. Finally, the cycle feed rate of cold rolled 304 stainless steel pipe was extracted when formulating springback through utilizing above results comprehensively and unloading law. Stress state, metal flow, finished pipe size and distribution of residual stress were obtained by finite element method to calculate the whole rolling process when the cycle feed rate was 10 mm, and the optimized model was verified through finished pipe size.
Abstract��A numerical model was established to calculate the cycle feed rate through studying the case of a cold pilger mill with the 304 stainless steel pipe. Firstly, the precise constitutive equation of 304 stainless steel was obtained through nonlinearly fitting the true stress�Cstrain data from unidirectional tensile test. Then, the numerical method to calculate the equivalent deformation was determined according to the plastic deformation feature of the steel tube during cold rolling and the incremental theory. Finally, the cycle feed rate of cold rolled 304 stainless steel pipe was extracted when formulating springback through utilizing above results comprehensively and unloading law. Stress state, metal flow, finished pipe size and distribution of residual stress were obtained by finite element method to calculate the whole rolling process when the cycle feed rate was 10 mm, and the optimized model was verified through finished pipe size.
Stinnertz, H.. Cold reducing of non-ferrous metal tubes by the cold-pilgering process[J]. Tube Pipe Technol, 1988, 27�C31.
[2]
D.Pociecha,BBoryczko,J. Osika,M. Mroczkowski. Analysis of tube deformation process in a new pilger cold rolling process[J].Archives of Civil and Mechanical Engineering, 2014, 14(3):376-382
[3]
Hideaki Abe, Tetsuya Iwamoto, Yoshiaki Yamamoto.Dimensional accuracy of tubes in cold pilgering[J]. Journal of Materials Processing Technology, 2016, 231:277-287.
[4]
Hideaki Abe, Munekatsu Furugen.Method of evaluating workability in cold pilgering[J].Journal of Materials Processing Technology, 2012, 212(8):1687-1693
[5]
M.Monkawa, S.Ueda, K.Kojima, M.Furugen. Stress analysis on the roll and mandrel of a cold pilger mill [J]. Journal of Mechanical Working Technology, 1984, 10:351-358.
[6]
P.Montmitonnet,RLog��,M. Hamery,Y.Chastel. 3D elastic�Cplastic finite element simulation of cold pilgering of zircaloy tubes[J].Journal of Materials Processing Technology, 2002, 125(9):814-820
[7]
M.Harada, A. Honda, S. Toyoshima. Simulation of cold pilgering process by a generalize plane strain FEM[J]. ASTM Special Technical Publication, 2006, 1467:233-247.
[8]
S.Mulot,AHacquin,P. Montmitonnet. A fully 3D finite element simulation of cold pilgering[J].Journal of Materials Processing Technology, 1996, 60(1-4):505-512
[9]
J.Osika, W. Libura. Mathematical model of tube cold
[10]
rolling in pilger mill[J].Journal of Materials Processing Technology, 1992, 34(1-4):325-332.
[11]
Hideaki Abe, Takashi Nomura, Yuuya Kubota.Lubrication of tube in cold pilgering[J].Journal of Materials Processing Technology, 2014, 214(8):1627-1637
[12]
N.P. Gurao,HAkhiani,J.A. Szpunar. Pilgering of Zircaloy-4: Experiments and simulations[J].Journal of Nuclear Materials, 2014, 453(1-3):158-168
[13]
Richard W Davies, Mohammad A.Khaleel,William CKinsel,Hussein M. Zbib. Anisotropic Yield Locus Evolution During Cold Pilgering of Titanium AlloyTubing[J].J Eng Mater-T ASME, 2002, 124(8):125-134
B.Lodej,KNiang,P. Montmitonnet. Accelerated 3D FEM computation of the mechanical history of the metal deformation in cold pilgering of tubes[J].Journal of Materials Processing Technology, 2006, 177(1-3):188-191
[16]
Zhu Jingqing.Calculation and application of deformation rolling process[J].Pipe, 2012, 29(4):17-22
[17]
Huang Liang.TA18 Rolled titanium alloy tubes multi-dimensional travel Pilger Finite element simulation: �� plastic deformation behavior analysis[J].Rare Metal Materials and Engineering, 2013, 42(3):741-745
2018, Vol. 25 
