|
|
|
| Dynamic Recrystallization Behavior of GCr15SiMn Bearing Steel during Hot Deformation |
| Dan ZHANG1,Ya-zheng LIU1,Le-yu ZHOU1,Qiang HAN1,Bo JIANG1,Zhong-zhi LI2 |
1. School of Material Science and Engineering, University of Science and Technology Beijing, Beijing 100083,China
2. Dongbei Special Steel Group Corporation Limited, Dalian 116105, Liaoning, China |
|
|
|
|
Abstract The hot deformation behavior of GCr15SiMn steel was studied through high temperature compression tests on the Gleeble-1500 thermal-mechanical simulator. The initiation and evolution of dynamic recrystallization (DRX) were investigated with microstructural analysis and then the process variables were derived from flow curves. In the present deformation conditions, the curves of strain hardening exponent (n) and the true strain (��) at the deformation temperature of 1423 K and strain rates of 0.1, 1 and 10 s-1 exhibit single peak and single valley. According to Zener-Hollomon and Ludwik equation, the experimental data have been regressed by using linear method. An expression of Z parameter and hot deformation equation of the tested steel were established. Moreover, the Q values of GCr15SiMn and GCr15 steels were compared. In order to determine the recrystallization fraction under different conditions, the volume fraction of DRX as a function of process variables, such as strain rate (), temperature (T), and strain (��), was established. It was found that the calculated results agreed with the microstructure of the steel at any deformation conditions.
|
|
Received: 13 June 2013
Published: 13 November 2014
|
| Fund:National Outstanding Youth Science Foundation of China |
|
|
|
| [1] |
Zong-ye Ding,Di Zhang,Qiao-dan Hu,,*,Long Zeng,Jian-guo Li,. Constitutive analysis and optimization on hot working parameters of as-cast high Cr ultra-super-critical rotor steel with columnar grains[J]. Chinese Journal of Iron and Steel, 2017, 24(9): 916-924. |
| [2] |
Yang Yun,Qing-wu Cai,,Bao-sheng Xie,*,Shuang Li. Effect of tempering temperature on strain hardening exponent and flow stress curve of 1000 MPa grade steel for construction machinery[J]. Chinese Journal of Iron and Steel, 2017, 24(9): 950-956. |
| [3] |
Yong-xing Jiao,Jian-sheng Liu*,Xing-wang Duan,Xiao-hua Zheng,Wen-wu He. Prediction of critical forging penetration efficiency for 06Cr19Ni9NbN steel by dynamic recrystallization[J]. Chinese Journal of Iron and Steel, 2017, 24(6): 649-653. |
| [4] |
Tao Xu,Guang-wei Wang,*,Jian-liang Zhang,Teng-fei Song,Run-sheng Xu. Non-isothermal study of gasification process of coal char and biomass char in CO2 condition[J]. Chinese Journal of Iron and Steel, 2017, 24(10): 985-990. |
| [5] |
Gan- lin XIE,An HE,Hai- long ZHANG,Gen- qi WANG,Xi- tao WANG. A Physically Based Dynamic Recrystallization Model Considering Orientation Effects for a Nitrogen Alloyed Ultralow Carbon Stainless Steel during Hot Forging[J]. Chinese Journal of Iron and Steel, 2016, 23(4): 364-371. |
| [6] |
Bao- sheng XIE,Qing- wu CAI,Wei YU,Shi- xin XU,Ban WANG. A Flow Stress Model for High Strength Steels with Low Carbon Bainite Structure[J]. Chinese Journal of Iron and Steel, 2016, 23(4): 372-379. |
|
|
|
|
2014, Vol. 21 
