|
|
|
| Effects of Chromium Addition on Preparation and Properties of Bulk Cementite |
| Bao-chao ZHENG,Zhi-fu HUANG,Jian-dong XING,Yi-yang XIAO,Xiao FAN,Yong WANG |
| State Key Laboratory for Mechanical Behavior of Materials, School of Materials Science and Engineering,Xi��an Jiaotong University, Xi��an 710049, Shaanxi, China |
|
|
|
|
Abstract Bulk cementites with the Cr contents of 0, 3��01, 6��03, 8��22, and 11��51 mass% were prepared by mechanical alloying (MA) and spark plasma sintering (SPS). The results indicated that when the Cr content was low (3��01 mass%), the phases were composed of cementite with a small amount of ��-Fe at a sintering temperature of 1173 K, but the microstructure became single-phase alloyed cementite as the Cr content was further increased. It showed that micro-addition of Cr was beneficial for promoting the formation of cementite. Furthermore, the mechanical performance of cementite can be greatly affected by the variation of Cr content. The hardness, elastic modulus and elastic recovery presented a remarkably increasing tendency with the addition of Cr, and the maximum micro-hardness and elastic modulus values reached 1070��74 HV and 199��32 GPa, respectively, which were similar to the precipitation phase (cementite) obtained by melting and casting techniques. Moreover, when the Cr content was below 11��51 mass%, the crystal structure of Fe3C-type cementite would not change with increasing the Cr content. A Cr atom replaced an Fe atom in the lattice of the cementite, and voids appeared when Cr was doped into the cementite at content of about 11��51 mass%, causing the relative density to decrease.
|
|
Received: 07 September 2015
Published: 09 August 2016
|
| Fund:����������ĥ�Ͻ���Fe2Bԭ�Ӳ����ͻ����俹ĥ��������Ϊ |
|
Corresponding Authors:
Jiandong Xing
E-mail: 283147831@qq.com
|
|
|
|
| [1] |
Wen-juan Ge,Xu-ting Li,Peng Li,Peng-chao Qiao,Jian-wei Du,Shuai Xu,Yan Wang*. Microstructures and properties of CuZrAl and CuZrAlTi medium entropy alloys prepared by mechanical alloying and spark plasma sintering[J]. Chinese Journal of Iron and Steel, 2017, 24(4): 448-454. |
| [2] |
Hui LI,Yong-feng LIANG,Feng YE. Evolution of Microstructure and Ordering in Rolling Process of Fe-6.5 mass% Si Alloy[J]. Chinese Journal of Iron and Steel, 2016, 23(5): 453-458. |
| [3] |
Xiao-ping DONG,Yan-rong PANG,Li-ying YANG,Qing WANG,Zhi-yuan LI. Effect of Spark Plasma Sintering Temperature on Electrochemical Properties of La0.82Mg0.18Ni3.50Co0.15 Alloy[J]. Chinese Journal of Iron and Steel, 2016, 23(5): 459-465. |
| [4] |
Xiao-dong LI,Ying CHANG,Zhi-yong WEI,Guang-yi CHEN,Ming-gang ZHU,Ling WENG. Preparation of Nanoscale Sm2Co17 Flakes by Ball Milling in Magnetic Field[J]. Chinese Journal of Iron and Steel, 2014, 21(5): 517-520. |
| [5] |
NI Hong��wei;HE Hang;LI Guang��qiang;LIU Jing. Preparation of Nanocrystalline 430L Stainless Steel by HEBM and SPS[J]. Chinese Journal of Iron and Steel, 2008, 15(4): 73-0. |
|
|
|
|
2016, Vol. 23 
