|
|
|
| Interfacial microstructure and mechanical properties of diffusion-bonded joints of titanium TC4 (Ti-6Al-4V) and Kovar (Fe-29Ni-17Co) alloys |
| Ting-feng Song1,Xiao-song Jiang1,Zhen-yi Shao1,2,De-feng Mo3,De-gui Zhu1,Min-hao Zhu1,Christina H. Young4,Zhi-ping Luo4 |
1 School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu 610031, Sichuan, China
2 Department of Material Engineering, Chengdu Technological University, Chengdu 611730, Sichuan, China
3 Key Laboratory of Infrared Imaging Materials and Detectors, Shanghai Institute of Technical Physics, Chinese Academy of Sciences, Shanghai 200083, China
4 Department of Chemistry and Physics, Fayetteville State University, Fayetteville, NC 28301, USA |
|
|
|
|
Abstract Diffusion bonding is a near net shape forming process that can join dissimilar materials through atomic diffusion under a high pressure at a high temperature. Titanium alloy TC4 (Ti-6Al-4V) and 4J29 Kovar alloy (Fe-29Ni-17Co) were diffusely bonded by a vacuum hot-press sintering process in the temperature range of 700-850��C and bonding time of 120 min, under a pressure of 34��66 MPa. Interfacial microstructures and intermetallic compounds of the diffusion-bonded joints were characterized by optical microscopy, scanning electron microscopy, X-ray diffraction(XRD) and energy dispersive spectroscopy (EDS).The elemental diffusion across the interface was revealed by electron probe microanalysis. Mechanical properties of joints were investigated by micro Vickers hardness and tensile strength. Results of EDS and XRD indicated that (Fe, Co, Ni)-Ti, TiNi, Ti2Ni, TiNi2, Fe2Ti, Ti17Mn3 and Al6Ti19 were formed at the interface. When the bonding temperature was raised from 700 to 850��C, the voids of interface were reduced and intermetallic layers were widened. Maximum tensile strength of joints at 53��5 MPa was recorded by the sintering process at 850��C for 120 min. Fracture surface of the joint indicated brittle nature, and failure took place through interface of intermetallic compounds. Based on the mechanical properties and microstructure of the diffusion-bonded joints, diffusion mechanisms between Ti-6Al-4V titanium and Fe-29Ni-17Co Kovar alloys were analyzed in terms of elemental diffusion, nucleation and growth of grains, plastic deformation and formation of intermetallic compounds near the interface.
|
|
Received: 11 November 2016
Published: 18 October 2017
|
|
|
|
| [1] |
CHMuralimohan, VMuthupandi, KSivaprasad.The influence of aluminum intermediate layer in dissimilar friction welds[J].International Journal of Materials Research, 2014, 105:350-357
|
| [2] |
Wang Ting, Zhang Binggang, Chen Guoqing, FengJicai, Tang Qi.Electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel with copper interlayer sheet [J].Transactions of Nonferrous Metals Society of China, 2010, 20:1829-1834
|
| [3] |
Wang Ting, Zhang Binggang, Chen Guoqing, FengJicai, Tang Qi.Electron beam welding of TiA15 titanium alloy to 304 stainless steel[J].Transactions of the China welding institution, 2010, 31:53-56
|
| [4] |
ChenShuhai, ZhangMingxin, HuangJihua, CuiChengji, ZhangHua, ZhaoXingke.Microstructures and mechanical property of laser butt welding of titanium alloy to stainless steel[J].Materials and Design, 2014, 53:504-511
|
| [5] |
Gen Satoh, YaoY.Lawrence, QiuCaian.Strength and microstructure of laser fusion-welded Ti-SS dissimilar mateial pair[J].The International Journal of Advanced Manufacturing Technology, 2013, 66:469-479
|
| [6] |
B. Shanmugarajan,G. Padmanabham. Fusion welding studies using laser on Ti-SS dissimilar combination[J].Optics and Lasers in Engineering, 2012, 50:1621-1627
|
| [7] |
ChenYungchang, TsengKuanghung, WangHsiangcheng.Small-scale projection lap-joint welding of kovar alloy and SPCC steel[J].Journal of Chinese Institute of Engineers, 2012, 35:211-218
|
| [8] |
ZhuWeiwei, ChenJichun, JiangChunhai.Effects of Ti thickness on microstructure and mechanical properties of alumina-Kovar joints brazed with Ag-Pd/Ti filler [J].Ceramics International, 2014, 40:5699-5705
|
| [9] |
WeiJinghui, DengBinghui, GaoXingqiang, YanJiuchun, ChenXiaoguang.Interface structure characterization of Fe36Ni alloy with ultrasonic soldering [J].Journal of Alloys and Compounds, 2013, 576:386-392
|
| [10] |
Zhang Lixia, MengDeqiang, Qi Junlei, FengJicai.Process of vacuum brazing 5005 aluminum alloy to 4J34 Kovar alloy [J].Transactions of Nonferrous Metals Society of China, 2015, 25:1435-1440
|
| [11] |
WangY, FengJ.C., ZhangL.X., He P., ZhangJ.H. Microstructure of alumina ceramic/Ag-Cu-Ti brazing alloy/Kovar alloy joint[J].Materials Science and Technology, 2007, 3:320-323
|
| [12] |
YangRui, LiNing, YanJiazhen.Microstructure and proformances of active brazing joint of WCeOi/Kovar alloy by vacuum brazing [J].Welding Technology, 2015, 44:24-28
|
| [13] |
SV. Gavrish, V.V. Loguinov, S.V. Puchnina.Technology for producing permanent joints between sapphire and metals [J].Welding International, 2015, 29:78-80
|
| [14] |
SSam, S. Kundu, S. Chatterjee.. Diffusion bonding of titanium alloy to micro-duplex stainless steel using a nickel alloy interlayer:Interface microstructure and strength properties [J].Materials and Design, 2012, 40:237-244
|
| [15] |
SKundu, S. Sam, B. Mishra, S. Chatterjee.. Diffusion bonding ofmicroduplex stainless steel and Ti alloy with and without interlayer: Interface microstructure and strength properties [J].Metallurgical and materials transactions A, 2014, 45:371-383
|
| [16] |
Su Hang, LuoXiaobing, ChaiFeng, ShenJunchang, SunXinjun, LuFeng.Manufacturing Technology and Application Trends of Titanium Clad Steel Plates [J].Journal of Iron and Steel Research, International, 2015, 22:977-982
|
| [17] |
SKundu, S. Sam, S. Chatterjee.. Interface microstructure and strength properties of Ti-6Al-4V and microduplex stainless steel diffusion bonded joints[J].[J].Materials and Design, 2011, 32:2997-3003
|
| [18] |
SKundu, D. Roy, S. Chatterjee, D. Olson, B. Mishra.. Influence of interface microstructure on the mechanical properties of titanium/17-4PH stainless steel solid state diffusion bonded joints[J].Materials and Design, 2012, 37:560-568
|
| [19] |
G Cacciamani, J. De Keyzer, R. Ferro, U.E. Klotz, J. Lacaze, P. Wollants.. Critical evaluation of the Fe-Ni, Fe-Ti and Fe-Ni-Ti alloy systems [J].Intermetallics, 2006, 14:1312-1325
|
| [20] |
TVigraman, D. Ravindran, R. Narayanasamy.. Effect of phase transformation and intermetallic compounds on the microstructure and tensile strength properties of diffusion-bonded joints between Ti-6Al-4V and AISI304L[J].Materials and Design, 2012, 36:714-727
|
| [21] |
ZhangBinggang, WangTing, ChenGuoqing, FengJicai.Contact reactive joining of TA15 and 304 stainless steel via a copper interlayer heated by electron beam with a beam deflection[J].Journal of Materials Engineering and Performance, 2012, 21:2067-2073
|
| [22] |
SH. Baghjari, S.A.A. AkbariMousavi. Experimental investigation on dissimilar pulsed Nd:YAG laser welding of AISI 420 stainless steel to kovar alloy[J].Materials and Design, 2014, 57:128-134
|
| [23] |
ASM.ASM metals handbook[J].ASM International, Metals Park(OH), 1990, 10th ed:-
|
| [24] |
KIshida, Y. Gao, K. Nagatsuka, M. Takahashi, K. Nakata.. Microstructures and mechanical properties of friction stir welded lap joints of commercially pure titanium and 304 stainless steel [J].Journal of Alloys and Compounds, 2015, 630:172-177
|
| [25] |
KaioNiitsu Campo, Leonardo ContriCampanelli, Luciano Bergmann, Jorge Fernandez dos Santos, ClaudemiroBolfarini.Microstructure and interface characterization of dissimilar friction stir welded lap joints between Ti-6Al-4V and AISI 304[J].Materials and Design, 2014, 56:139-145
|
| [26] |
Qin Bin, ShengGuangmin, YuanXinjian.Welding characteristics and technology of titanium-steel diffusion bonding [J].Welding Technology, 2007, 36:7-9
|
| [1] |
Ying Ci,*,Zhan-zhan Zhang. Simulation study on heat-affected zone of high-strain X80 pipeline steel[J]. Chinese Journal of Iron and Steel, 2017, 24(9): 966-973. |
| [2] |
Xiao-li Zhao,,Yong-jian Zhang,Cheng-wei Shao,Wei-jun Hui,Han Dong. Thermal stability of retained austenite and mechanical properties of medium-Mn steel during tempering treatment[J]. Chinese Journal of Iron and Steel, 2017, 24(8): 830-837. |
| [3] |
Hang-wei Zhou,,Hui-qun Liu,,Dan-qing Yi,,Yu Xiao,,Xiao-long Zhao,Jian Wang,Qi Gao. Effect of �� phase on fatigue crack growth of Ti-6242 alloy[J]. Chinese Journal of Iron and Steel, 2017, 24(8): 811-822. |
| [4] |
Reng-chong Xu,,Yan-lin He,,Hu Jiang,,Hua Wang,,Na-qiong Zhu,,Xiao-gang Lu,, Lin Li,. Microstructures and mechanical properties of ferrite-based lightweight steel with different compositions[J]. Chinese Journal of Iron and Steel, 2017, 24(7): 737-742. |
| [5] |
Wei-jun Hui,*,Na Xiao,Xiao-li Zhao,Yong-jian Zhang,Yu-feng Wu. Effect of vanadium on dynamic continuous cooling transformation behavior of medium-carbon forging steels[J]. Chinese Journal of Iron and Steel, 2017, 24(6): 641-648. |
| [6] |
Yong-xing Jiao,Jian-sheng Liu*,Xing-wang Duan,Xiao-hua Zheng,Wen-wu He. Prediction of critical forging penetration efficiency for 06Cr19Ni9NbN steel by dynamic recrystallization[J]. Chinese Journal of Iron and Steel, 2017, 24(6): 649-653. |
|
|
|
|
2017, Vol. 24 
