|
|
|
| Effects of strain states on stability of retained austenite in medium Mn steels |
| Mei Xu1,Yong-gang Yang1,Jia-yong Chen2,Di Tang3,Hai-tao Jiang1,Zhen-li Mi1,* |
1 Institute of Engineering Technology, University of Science and Technology Beijing, Beijing 100083, China
2 BYD Auto Industry Company Limited, Shenzhen 518116, Guangdong, China
3 Collaborative Innovation Center of Steel Technology, University of Science and Technology Beijing, Beijing 100083, China |
|
|
|
|
Abstract Based on uniaxial tensile and plane strain deformation tests, the effects of strain states on the stability of RA (retained austenite) in medium Mn steels, which were subjected to IA (intercritical annealing) and Q&P (quenching and partitioning) processing, were investigated. The volume fractions of RA before and after deformation were measured at different equivalent strains. The transformation behaviors of RA were also investigated. The stability of RA differed across two different transformation stages at the plane strain state: the stability was much lower in the first stage than in the second stage. For the uniaxial tension strain state, the stability of RA corresponded only to a single transformation stage. The main reason was that there were two types of transformations from RA in the medium Mn steel for the plane strain state. One type was that the martensite originated in the strain-induced stacking faults (SISF). The other type was the strain-induced directly twin martensite at a certain equivalent strain. However, for the uniaxial tension state, only the strain-induced twin martensite was observed. Dislocation lines and dislocation tangles were also observed in specimens deformed at different strain states. In addition, complex microstructures of stacking faults and lath-like phases were observed within a grain at the plane strain state.
|
|
Received: 14 August 2017
Published: 01 December 2017
|
|
|
|
| [1] |
S. Curtze, V. T. Kuokkala, M. Hokka, P. Peura.Deformation behavior of TRIP and DP steels in tension at different temperatures over a wide range of strain rates[J].Mater. Sci. Eng. A, 2009, 507(1-2):124-131
|
| [2] |
R. Song, D. Ponge, D. Raabe, J. G. Speer, D. K. Matlock.Overview of processing, microstructure and mechanical properties of ultrafine grained bcc steels[J].Mater. Sci. Eng. A, 2006, 441(1-2):1-17
|
| [3] |
K. Yang, Z. J. Zhang, F. Y. Dong, Q. Q. Duan, Z. F. Zhang.Strain rate effects on tensile deformation behaviors for Fe-22Mn-0.6C-(1.5Al) twinning-induced plasticity steel[J].Mater. Sci. Eng. A, 2014, 6.7:551-558
|
| [4] |
I. Latypov, S. Shin, B. C. De Cooman, H. S. Kim.Micromechanical finite element analysis of strain partitioning in multiphase medium manganese TWIP+ TRIP steel[J].Acta Mater., 2016, 108:219-228
|
| [5] |
S. Lee, B.C. De Cooman.Tensile behavior of intercritically annealed 10 pct Mn multi-phase steel[J].Metall. Mater. Trans. A, 2014, 45:709-719
|
| [6] |
S. Lee, B. C. De Cooman.Effect of the intercritical annealing temperature on the mechanical properties of 10 pct Mn multi-phase steel[J].Metall. Mater. Trans. A, 2014, 45(11):5009-5061
|
| [7] |
Zhao, Y. Shen, L. Qiu, Y. Liu, X. Sun, L. Zuo.Effects of intercritical annealing temperature on mechanical properties of Fe-7.9Mn-0.14Si-0.05Al-0.07C steel[J].Mater. (Basel), 2014, 7:7891-7906
|
| [8] |
Y. Lee, J. Jeong, J. Han, S. J. Lee, S. Lee, Y. K. Lee.Coupled strengthening in a medium manganese lightweight steel with an inhomogeneously grained structure of austenite[J].Acta Mater., 2015, 84:1-8
|
| [9] |
C. De Cooman, S. J. Lee, S. Shin, E. J. Seo, J. G. Speer. Combined Intercritical Annealing and Q&P Processing of Medium Mn Steel[J].Metall. Mater. Trans. A, 2017, 48(1):39-45
|
| [10] |
S. Li, H. Y. Gao, H. Nakashima, S. Hata, W. H. Tian.In-situ study of the deformation-induced rotation and transformation of retained austenite in a low-carbon steel treated by the quenching and partitioning process[J].Mater. Sci. Eng. A, 2016, 649:417-425
|
| [11] |
Song, H. Yu, L. Li, T. Zhou, J. Lu, X. Liu.The stability of retained austenite at different locations during straining of I&Q&P steel[J].Mater. Sci. Eng. A, 2016, 670:326-334
|
| [12] |
N. Han, C. S. Oh, G. Kim, O. Kwon.Design method for TRIP-aided multiphase steel based on a microstructure-based modelling for transformation-induced plasticity and mechanically induced martensitic transformation[J].Mater. Sci. Eng. A, 2009, 499(1):462-468
|
| [13] |
H. Cai, H. Ding, R. D. K. Misra, Z. Y. Ying.Austenite stability and deformation behavior in a cold-rolled transformation-induced plasticity steel with medium manganese content[J].Acta Mater., 2015, 84:229-236
|
| [14] |
Jimenez-Melero, N. H. Van Dijk, L. Zhao, J. Sietsma, S. E..Martensitic transformation of individual grains in low-alloyed TRIP steels[J].Offerman, Scripta Mater., 2007, 56(1):421-424
|
| [15] |
Blond��, E. Jimenez-Melero, L. Zhao.High-energy X-ray diffraction study on the temperature-dependent mechanical stability of retained austenite in low-alloyed TRIP steels[J].Acta Mater., 2012, 60(2):565-577
|
| [16] |
F. Shen, L. N. Qiu, X. Sun, L. Zuo, P. K. Liaw, D. Raabe.Effects of retained austenite volume fraction, morphology, and carbon content on strength and ductility of nanostructured TRIP-assisted steels[J].Mater. Sci. Eng. A, 2015, 636:551-564
|
| [17] |
B. Timokhina, P. D. Hodgson, E. V..Effect of microstructure on the stability of retained austenite in transformation-induced-plasticity steels[J].Pereloma, Metall. Mater. Trans. A, 2004, 35(8):2331-2341
|
| [18] |
K. Shan, W. G. Zhang, S. H. Li, D. P. Shen.The influence of the stress state on retained austenite stability in transformation induced plasticity steels[J].J. Shanghai Jiaotong U., 2006, 10:1691-1693
|
| [19] |
Noriyuki, Y. Tomota.A micromechanic modeling for transformation induced plasticity in steels[J].Mater. Sci. Eng. A, 2000, 285:346-352
|
| [20] |
Sugimoto, N. Usui, M. Kobayashi, S. Hashimoto.Effects of volume fraction and stability of retained austenite on ductility of TRIP-aided dual-phase steels[J].Testu-to-Hagane, 1992, 32(12):1311-1311
|
| [21] |
W. X. Song.Metallography[J].Regulation in Peking, China, 2013, :335-335
|
| [22] |
J. Seo, L. Cho, Estrin Y, B. C. De Cooman.Microstructure-mechanical properties relationships for quenching and partitioning (Q&P) processed steel[J].Acta Mater., 2016, 113:124-139
|
| [23] |
B. Olson, M. Cohen.A general mechanism of martensitic nucleation: Part III. Kinetics of martensitic nucleation[J].Metall. Trans. A, 1976, 7(12):1915-1923
|
| [24] |
B. Olson, M. Cohen.A general mechanism of martensitic nucleation: Part II. FCC �� BCC and other martensitic transformations[J].Metall. Trans. A, 1976, 7(12):1905-1914
|
| [25] |
W. Brooks, M. H. Loretto, R. E. Smallman.Direct observations of martensite nuclei in stainless steel[J].Acta Metall., 1979, 27(12):1839-1847
|
| [1] |
Xiao-gang Wang,Ming-xin Huang,*. Temperature dependence of L��ders strain and its correlation with martensitic transformation in a medium Mn transformation-induced plasticity steel[J]. , 2017, 24(11): 1073-1077. |
| [2] |
Chang WANG,Wen-quan CAO,Yun HAN,Cun-yu WANG,Chong-xiang HUANG,Han DONG. Influences of Austenization Temperature and Annealing Time on Duplex Ultrafine Microstructure and Mechanical Properties of Medium Mn Steel[J]. Chinese Journal of Iron and Steel, 2015, 22(1): 42-47. |
|
|
|
|
2017, Vol. 24 
