|
|
High-temperature creep constitutional model ofQ460E steel and effect of creep on bulging deformation of continuous casting slab |
Long Guo 1,2 . Yun-huan Sui . Xing-zhong Zhang |
1 National Engineering Research Centre for Equipment and Technology of Cold Strip Rolling, Yanshan University, Qinhuangdao 066004, Hebei, China 2 Hesteel Group Tangsteel Company, Tangshan 063016, Hebei, China |
|
|
Abstract Mechanical properties and creep behavior of Q460E continuous casting slab were studied by means of uniaxial tensile tests on a Gleeble-3800 thermomechanical simulator from 1000 to 1100 C. The high-temperature creep constitutional equation was derived based on experimental data. The parameters in the equation were calculated by using the regression analysis inverse-estimation method. The experimental curves in the primary and secondary creep stages are fitted well. A three-dimensional elastic–plastic and creep finite element model was proposed in order to investigate the bulging deformation of slab and the bulging deformation at the beginning position of bending segment on the slab continuous casting machine was computed accurately. The results indicate that the maximum bulging deformation appears at the geometric center of the slab. The maximum value of the bulging deformation obtained by the elastic–plastic analysis is 1.301 mm. Considering the creep effect, the deformation increases to 1.827 mm which is about 1.4 times the value obtained by the elastic–plastic analysis. The calculation of bulging deformation using the elastic–plastic creep model is more reliable and accurate.
|
Received: 22 August 2017
Published: 07 January 2019
|
|
|
|
Cite this article: |
GUO Long,DUO Wen-Qiong,ZHANG Xin-Zhong. High-temperature creep constitutional model ofQ460E steel and effect of creep on bulging deformation of continuous casting slab[J]. Journal of Iron and Steel Research International, 2018, 25(11): 1123-1130.
|
|
|
|
[1] |
H.A. Lanjewar, P. Tripathi, M. Singhai, K. Patra, J. Mater. Eng. Perform. 23 (2014) No. 10, 3600-3609.
|
[2] |
H. Tomono, Ironmaking Steelmaking 42 (2015) No. 4, 242-251.
|
[3] |
F. Pascon, A.M. Habraken, Comput. Methods. Appl. Mech. Eng. 196 (2007) No. 21, 2285-2299.
|
[4] |
M.O. Elbealy, Ironmaking Steelmaking 40 (2013) No. 3, 167-188.
|
[5] |
M.F. Ashby, D.R.H. Jones, Engineering materials 1: an introduction to properties, applications and design, Elsevier Science, New York, 2011, pp.311-323.
|
[6] |
N. Ottosen, M. Ristinmaa, The mechanics of constitutive modeling, Elsevier, Amsterdam, 2005, pp.551-562.
|
[7] |
X.Z. Zhang, L. Guo, ISIJ Int. 57 (2017) No. 1, 76-83.
|
[8] |
L. Guo, X.Z. Zhang, C.X. Feng, J. Iron Steel Res. Int. 24 (2017) No. 6, 595-600.
|
[9] |
K. Okamura, H. Kawashima, ISIJ Int. 29 (1989) No. 8, 666-672.
|
[10] |
A. Grill, K. Schwerdtfeger, Ironmaking Steelmaking 6 (1979) No. 3, 131-135.
|
[11] |
J.S. Ha, J.R. Cho, B.Y. Lee, M.Y. Ha, J. Mater. Process. Technol. 113 (2001) No. 1, 257-261.
|
[12] |
C.S. Li, B.G. Thomas, Metall. Mater. Trans. B 35 (2004) No. 6, 1151-1172.
|
[13] |
S. Koric, B.G. Thomas, J. Mater. Process. Technol. 197 (2008) No. 1, 408-418.
|
[14] |
T. Suzuki, K.H. Tacke, K. Wuennenberg, Ironmaking Steelmaking 15 (1988) No. 2, 90-100.
|
[15] |
A. S. Mammar, D. Gruber, H. Harmuth, S.L. Jin, Ceram. Int. 42 (2016) No. 6, 6791-6799.
|
[16] |
J. Brnic,G. Turkalj,M. Canadija, D. Lanc, J. Constr. Steel. Res. 67 (2011) No. 12, 1948-1952.
|
[17] |
J. Brnic, M. Canadija, G. Turkalj, Bull. Mater. Sci. 33 (2010) No. 4, 475-481.
|
[18] |
A.G.D. Reis, D.A.P. Reis, A.J. Abdalla, G. Otubo, Mater. Charact. 107 (2015) 350-357.
|
[19] |
M. Cowan, K. Khandelwal, Eng.Struct. 80 (2014) No. 23, 426-434.
|
[20] |
Z. H. Dong, D.F. Chen, M.J. Long, X. Zhang, J.L. Shen, Chin. J. Mater. Res. 27 (2013) No. 3, 273-278 (in Chinese).
|
[21] |
H. S. Dong, X. D. Kang, G.D. Wang, X. H. Liu, J. Northeast. Univ. 25 (2004) No. 1, 40-43 (in Chinese).
|
[22] |
H. Xu, J. Yuan, Y.Z. Ni, J. Mater. Sci. Eng. 31 (2013) No. 4, 568-571 (in Chinese).
|
[23] |
C. S. Liu, T.W. Yang, W.H. Wu, Scripta Mater. 37 (1997) No. 4, 425-429
|
|
|
|