|
|
|
| Influence of slip ratio on worn-surface microstructure and fatigue wear behavior of D2 wheel steel |
| Chun-peng Liu1 . Xiu-juan Zhao1,2 . Peng-tao Liu1 . Chong Xu3 . Rui-ming Ren1,2 |
1 School of Material Science and Engineering, Dalian Jiaotong University, Dalian 116028, Liaoning, China
2 Key Laboratory of Critical Materials of Rail Transportation in Liaoning Province, Dalian Jiaotong University, Dalian 116028, Liaoning, China
3 School of Mechanical Engineering, Dalian Jiaotong University, Dalian 116028, Liaoning, China |
|
|
|
|
Abstract To investigate the worn-surface microstructure and fatigue cracks in D2 wheel steel under the pure rolling and 0.5% slip ratio conditions, a rolling wear test using a GPM-40 wear machine to simulate the wheel/rail operation was performed. After testing, a transmission electron microscope, a scanning electron microscope with electron backscatter diffraction, and micro-hardness testers were used to characterize the microstructure and fatigue cracks. The surface microstructure and hardness of the pure rolling sample were in a steady state after 8 × 104 cycles; however, the 0.5% slip ratio sample reached a steady state after 7 × 103 cycles. Regardless of whether the test uses the slip ratio, the orientation of lamellar pearlites gradually became parallel to the surface and a portion of lamellar cementites was fragmented and dissolved during the formation of steady-state microstructure. The slip ratio accelerates this process. The hardening mechanism of the samples shows a decrease in the lamellar spacing of pearlite and the refinement of proeutectoid ferrite (PF). As the number of cycles increased, plastic deformation of samples became increasingly severe and the wear mechanism of the samples was fatigue wear in steady state. The sample surfaces formed shallow cracks, which gradually peeled off. The slip ratio accelerated the initiation and propagation of fatigue cracks because of the high friction stress on the contact surface. Most fatigue cracks initiated at the interface of pearlite and PF and in the PF region.
|
|
Received: 13 September 2017
Published: 23 January 2019
|
|
|
|
| Cite this article: |
|
LIU Chun-Peng,DIAO Xiu-Juan,LIU Peng-Shou, et al. Influence of slip ratio on worn-surface microstructure and fatigue wear behavior of D2 wheel steel[J]. Journal of Iron and Steel Research International, 2018, 25(12): 1278-1286.
|
|
|
|
| [1] |
A. Ekberg, E. Kabo, Wear 258 (2005) 1288-1300.
|
| [2] |
S. Pal, C. Valente, W. Daniel, M. Farjoo, Wear, 284 (2012) 30-42.
|
| [3] |
Q.H.Li, C.Zhang, H.Chen, H.Chen, Z.G.Yang, J.Iron.Steel.Res.Int. 23(10)1054-1060.
|
| [4] |
W.R. Tyfour, J.H. Beynon, A. Kapoor, Wear 180 (1995) 79-89
|
| [5] |
Y. Zhou, J.F. Peng, W.J. Wang, X.S. Jin, M.H. Zhu, Wear 362-363(2016)78-86.
|
| [6] |
Y. Zhou, J.F. Peng, Z.P. Luo, B.B. Cao, X.S. Jin, M.H. Zhu, Wear 362-363(2016)8-17.
|
| [7] |
H. Chen, C. Zhang, W.B.Liu, Q.H.Li, H.Chen, Z.G.Yang, Mater. Sci. Eng. A 655(2016)50–59.
|
| [8] |
S. Pal, W.J. Daniel, C.H. Valente, A. Wilson, A. Atrens, Eng .Fail. Anal. 22 (2012) 152–165.
|
| [9] |
L. Ma, C.G.He, X.J.Zhao, J. Guo, Y. Zhu, W.J. Wang, Q.Y. Liu, X.S. Jin, Wear 366—367(2016)13-26.
|
| [10] |
T. Makino, T. Kato, K. Hirakawa, Int. J. Fatigue 36(2012)68-79
|
| [11] |
Y.C.Chiou，J.R.Hwan, Tribol. Int. 24 (1991)101-107.
|
| [12] |
J.E. Garnham, C.L. Davis, Wear 271 (2011) 100–112.
|
| [13] |
F.J. Franklin, J.E. Garnham, D.I. Fletcher, C.L. Davis, A. Kapoor, Wear 265 (2008) 1332–1341.
|
| [14] |
J. E .Garnham,C. L. Davis, Wear 265 (2008) 1363–1372.
|
| [15] |
J.H. Beynon, J.E. Garnham, K.J. Sawley, Wear 192 (1996) 94-111.
|
| [16] |
S.P. Timoshenko, J.N. Goodier, H.N. Abramson, J. Appl. Mech. 37 (1970) 888.
|
| [17] |
Y.Ivanisenko, W.Lojkowski, R.Z.Valiev, H.J.Fecht, Acta Mater 51(2003) 5555-5570.
|
| [18] |
N.R. Tao , Z.B. Wang , W.P. Tong , M.L. Sui , J. Lu , K. Lu, Acta Mater 50 (2002) 4603–4616
|
| [19] |
J.F.Archard. in: M.B.Peterson and W.O.Winer (Eds) Wear theory and mechanism. wear control handbook, American Society of Mechanical Engineers,New York, 1980,pp.35-80.
|
| [20] |
D.G. Hennessy, V. Sharma, G.S. Ansell, Metallurg. Trans.A. 14 (1983) 1013-1019.
|
| [21] |
E. Macherauch, O. V?hringer, HTM 41(1986): 71-91.
|
| [22] |
G. Langford, Metallurg Tran A. 8 (1977) 861-875.
|
| [23] |
C.Urashima, S.Nishida. Fatigue crack initiation and propagation behavior in pearlite structures[C]//Fatigue'96. Sixth International Fatigue Congress. 1996, 1: 319-324.
|
| [24] |
K. Lu, Science 345(2014) 1455-1456.
|
| [25] |
John E. Garnham, Claire L. Davis, Wear 265 (2008) 1363–1372.
|
|
|
|
2018, Vol. 25 
