|
|
|
| Homogeneity analysis of Y-bearing 12Cr ferritic/martensitic steel fabricated by vacuum induction melting and casting |
| Wei-wei Guo1, Xiao-xin Zhang1,2,3, Ying-xue Chen1, Zhi-yuan Hong1, Qing-zhi Yan1 |
1 Institute of Nuclear Materials, School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China
2 Advanced Energy Research Center, Shenzhen University, Shenzhen 518060, Guangdong, China
3 Key Laboratory of Optoelectronic Devices and Systems of Ministry of Education and Guangdong Province, College of Optoelectronic Engineering, Shenzhen University, Shenzhen 518060, Guangdong, China |
|
|
|
|
Abstract Advanced oxide metallurgy technique was adopted to produce 100-kg Y-bearing 12Cr ferritic/martensitic steel via vacuum induction melting and casting route. Subsequently, nine specimens at top, middle and bottom regions of the sheet were characterized to evaluate the homogeneity of chemical composition, microstructure and mechanical properties. The small vibration of hardness (200–220 HBW), ultimate tensile strength (672–678 MPa), yield strength (468–480 MPa), total elongation (26.2%–30.5%) and Charpy energy at room temperature (98–133 J) and at − 40 °C (12–40 J) demonstrated that mechanical properties’ homogeneity of Y-bearing steel was acceptable although slight Y segregation and inhomogeneous microstructure occurred at the bottom. Furthermore, the effect of Y content on microstructure characteristics and mechanical properties was explained and the comparison of failure mechanism for the dual-phase steel between tensile test (i.e., quasi-static loading) and Charpy test (i.e., dynamic loading) was discussed in detail.
|
|
Received: 14 June 2019
Published: 25 August 2020
|
|
|
|
| Cite this article: |
|
Wei-wei Guo,Xiao-xin Zhang,Ying-xue Chen, et al. Homogeneity analysis of Y-bearing 12Cr ferritic/martensitic steel fabricated by vacuum induction melting and casting[J]. Journal of Iron and Steel Research International, 2020, 27(8): 940-951.
|
|
|
|
| [1] |
Wei‑gang Li1, Lu Xie1, Yun‑tao Zhao1, Zi‑xiang Li2, Wen‑bo Wang3. Prediction model for mechanical properties of hot-rolled strips by deep learning[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2020, 27(9): 1045-1053. |
| [2] |
Da‑peng Li, Hua‑zhang Wu, Hai‑feng Wang, Hong Li. Growth of solidified shell in bloom continuous casting mold of hypo-peritectic steel based on a FeS tracer method[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2020, 27(7): 782-787. |
| [3] |
Shan-shan Liu, Liang Bai, Bo Wang, Yu Yao, Jun-kai Huang, Zheng Chen, Jie-yu Zhang. Numerical simulations of solidification and hot tearing for continuous casting of duplex stainless steel[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2020, 27(6): 643-655. |
| [4] |
Jian‑min Li, Mao‑fa Jiang, Jun‑xiang Ning, Jun Zhai. Effect of casting speed on dendrite arm spacing of Mn13 steel continuous casting slab[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2020, 27(6): 665-672. |
| [5] |
Chun‑xu Wang, Yuan‑hang Gao, Yong Li, Shun Han, Shao‑zun Liu, Peng‑jie Zhang. Effects of solid-solution temperature on microstructure and mechanical properties of a novel 2000 MPa grade ultra-high-strength steel[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2020, 27(6): 710-718. |
| [6] |
Ming Lei, Wei‑jun Hui, Jiao‑jiao Wang, Yong‑jian Zhang, Xiao‑li Zhao. Microstructure and mechanical properties of hot-rolled V-microalloyed Al-containing medium-Mn steel[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2020, 27(5): 537-548. |
|
|
|
|
2020, Vol. 27 
