|
|
|
| Effect of copper on edge cracking behavior and microstructure of rolled austenitic stainless steel plate |
| Guang-hui Zhao1,2, Jian Zhang1,2, Juan Li1,2, Hua-ying Li1,2, Hai-tao Liu3, Li-feng Ma1,2 |
| 1 School of Mechanical Engineering, Taiyuan University of Science and Technology, Taiyuan 030024, Shanxi, China; 2 Shanxi Provincial Key Laboratory of Metallurgical Device Design Theory and Technology, Taiyuan 030024, Shanxi, China; 3 State Key Laboratory of Rolling and Automation, Northeastern University, Shenyang 110819, Liaoning, China |
|
|
|
|
Abstract Cu is known to affect the edge cracking characteristics of austenitic stainless steel as it causes embrittlement. The hot rolling test of four kinds of austenitic stainless steel with different copper content (0, 2.42, 3.60 and 4.35 wt.%) was carried out to examine the effect of hot rolling cracks on steel containing different copper contents. The evolution of crack and microstructure was analyzed using the scanning electron microscope, energy-dispersive spectrometer, electron back scattered diffraction and transmission electron microscope. Experimental results showed an upward trend in edge cracking degree when Cu content was 4.35%, and the crack extended from the edge of the steel plate to the middle by about 14 mm. Besides, severe oxidation was observed inside the crack by fractography. With the increase in copper content at 1250 °C, the content of {110}<112> brass and {112}<111> copper textures decreased. When the content of copper was 4.35%, the decrease was most significant, and {112}<111> copper texture content decreased to only 0.5%. Generally, the textures of 2.42%Cu and 3.60%Cu 304L steel changed little, while a large change in the texture of 4.35%Cu 304L steel was observed. To conclude, the increase in rolling temperature can prevent edge crack and its propagation effectively.
|
|
|
|
|
|
| Cite this article: |
|
Guang-hui Zhao,Jian Zhang,Juan Li, et al. Effect of copper on edge cracking behavior and microstructure of rolled austenitic stainless steel plate[J]. Journal of Iron and Steel Research International, 2022, 29(2): 281-294.
|
|
|
|
| [1] |
Jian-tao Ju, Chen-mei Tang, Guang-heng Ji, Xiang-dong Xing, Gui-qing Zhao, Xin-tai Jiang, Feng-lin Lu. Effect of BaSO4 on phase composition and sintering process of iron ore fines[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2022, 29(3): 408-417. |
| [2] |
Shi-ping Xi, Xin-liang Gao, Wei Liu, Yan-lu Lu, Gui-qin Fu, Hui-cheng Tao, Yong-chang Zang. Hot deformation behavior and processing map of low-alloy offshore steel[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2022, 29(3): 474-483. |
| [3] |
Zhi-xiang Fu, Geng-wei Yang, Ru-yang Han, Yao-wen Xu, Xin-ping Mao, Si-qian Bao, Gang Zhao. Influence of coiling temperature on microstructure and mechanical properties of a hot-rolled high-strength steel microalloyed with Ti, Mo and V[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2022, 29(3): 484-493. |
| [4] |
Li-ying Liu, Ping Yang, Dan-dan Ma, Xin-fu Gu. Surface effect induced phase transformation by Mn removal during annealing and its textures in cold-rolled high manganese transformation-induced plasticity steel[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2022, 29(3): 494-502. |
| [5] |
Bo Ning, Hui-bin Wu, Gang Niu, Xin-pan Yu. Cold compression deformation method for reducing residual stress and uniformizing micro-property in ferrite steel[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2022, 29(3): 503-511. |
| [6] |
Xin-bo Ji, Si-xin Zhao, Li-ming Fu, Jian Peng, Jia-qiang Gao, Da-jiang Yu, Zong-ze Huang, Ai-dang Shan. High cycle rotating bending fatigue performance and fracture behavior in a pearlite–ferrite dual-phase steel[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2022, 29(3): 519-528. |
|
|
|
|
2022, Vol. 29 
