|
|
Numerical investigation on thermomechanical behavior of alumina– calcium hexaluminate refractories for purging plug |
Li-ping Pan1,2, Ya-wei Li1,2, Fang-guan Tan1,2, Yi-chen Chen1,2, Yang-fan Xu1,2, Zhu He1,2, Bao-kuan Li1,2 |
1 The State Key Laboratory of Refractories and Metallurgy, Wuhan University of Science and Technology, Wuhan 430081, Hubei, China 2 National-Provincial Joint Engineering Research Center of High Temperature Materials and Lining Technology, Wuhan University of Science and Technology, Wuhan 430081, Hubei, China |
|
|
Abstract Alumina–spinel refractories used in slit-type purging plugs are susceptible to cross-sectional damage, resulting in a serious mismatch between their service life and that of ladle. Alumina–calcium hexaluminate refractories have gradually become the new trend in purging plug materials with the development of refining technology. The thermomechanical damage of slit-type purging plugs with alumina–calcium hexaluminate refractory was investigated by the thermo-solid coupling simulation. Combined with the polynomial fitting and design of experiments methods, the influence of thermophysical parameters on temperature and thermal stress of alumina–calcium hexaluminate refractories for purging plugs was systematically analyzed. The results show that the maximum thermal stress of the purging plugs appears during the stages of steel transporting and stirring, and the vulnerable parts are located above Y = 0.323 m. The thermal conductivity and the coefficient of thermal expansion of the material are the most sensitive parameters to the temperature and thermal stress inside the structure, respectively. The addition of more calcium hexaluminate can relieve the stress concentration and large deformation around the slits. Consequently, when the content of calcium hexaluminate is 47 wt.% and in the form of aggregate-binder, the temperature and thermal stress distribution inside the refractory are optimal, which can effectively improve the service life of the slit-type purging plug.
|
|
|
|
|
Cite this article: |
Li-ping Pan,Ya-wei Li,Fang-guan Tan, et al. Numerical investigation on thermomechanical behavior of alumina– calcium hexaluminate refractories for purging plug[J]. Journal of Iron and Steel Research International, 2024, 31(02): 389-400.
|
|
|
|
[1] |
Wen-quan Sun, Sheng-yi Yong, Tie-heng Yuan, Ting-song Yang, An-rui He, Chao Liu, Rui-chun Guo. Effect of post rolling stress on phase transformation behavior of microalloyed dual phase steel[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2024, 31(3): 688-699. |
[2] |
Sha Zhang, Yu-chao Wu, Yu Li, Zhong-pei Dai, Dan Jia, Yan-fei Xu, Guang-sheng Zeng, Zhi-ming Guo, Jian Liu. Effect of stabilizing treatment on microstructure and stress rupture properties of phosphorus microalloyed Inconel 706 alloy[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2023, 30(8): 1613-1621. |
[3] |
Xiao-hua Li, Chen-xi Liu, Teng Zhang, Chuan-tao Lv, Jiang-cheng Liu, Ran Ding, Zhi-ming Gao, Rui Wang, Yong-chang Liu. Effect of pH and applied stress on hydrogen sulfide stress corrosion behavior of HSLA steel based on electrochemical noise analysis[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2023, 30(12): 2531-2540. |
[4] |
Jian-zhao Shang, Bao-liang Liu, Kai Shi, Yang Liu, Yong-hao Mi, Wen-hao Fan, Yi-xian He. Effect of stainless steel fibers on properties of MgO–C refractories[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2023, 30(11): 2186-2193. |
[5] |
Wen-wen Zhang, Wan Zheng, Wen Yan, Guang-qiang Li. Formation mechanism of interface reaction layer between microporous magnesia refractories and molten steel and its effect on steel cleanliness[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2023, 30(09): 1743-1754. |
[6] |
Zhi-yuan Liu, Li-hao Zhang, Cheng Ji, Miao-yong Zhu, Chong-jun Wang. Flow stress and constitutive relations of ship plate steel continuous casting slab with solidification end reduction process[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2023, 30(09): 1769-1781. |
|
|
|
|