|
|
Water modeling on fluid flow and mixing phenomena in a BOF steelmaking converter |
Xin-yu Cai1, Hao-jian Duan1, Ding-han Li1, An-jun Xu1, Li-feng Zhang2 |
1 School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing (USTB), Beijing 100083, China 2 School of Mechanical and Materials Engineering, North China University of Technology, Beijing 100144, China |
|
|
Abstract A 1:8 physical water model was constructed to investigate the fluid flow and mixing phenomena in the basic oxygen furnace (BOF) converter. The particle image velocimetry was employed to measure the velocity distribution of the bath and the high-speed camera was applied to capture the cavity shape in the combined blowing BOF converter. The mixing time for varied operating conditions was measured by the stimulus-response approach. The cavity depth increased with the decrease in the lance height and the increase in the top gas flow rate while the bottom blowing gas had little influence on the cavity depth. The minimum cavity depth was obtained under the condition of a 69.8 m3/h top gas flow rate, a 287.5 mm lance height and a 0.93 m3/h bottom blowing gas flow rate, which was 161.2 mm. The mixing time decreased as the lance height decreased and the top blowing gas flow rate increased. The mixing time was first decreased and then increased with the increase in the bottom gas flow rate. With the condition of 69.8 m3/h gas flow rate of top blowing, the 287.5 mm lance height and the 0.93 m3/h gas flow rate of bottom blowing, the mixing time in the converter was 48.65 s. The empirical formula between the stirring power and the mixing time in the converter was calculated.
|
|
|
|
|
Cite this article: |
Xin-yu Cai,Hao-jian Duan,Ding-han Li, et al. Water modeling on fluid flow and mixing phenomena in a BOF steelmaking converter[J]. Journal of Iron and Steel Research International, 2024, 31(3): 595-607.
|
|
|
|
[1] |
Jia-chen Pang, Guo-yu Qian, Sheng Pang, Wen-hui Ma, Guo-guang Cheng. Design of a submerged entry nozzle for optimizing continuous casting of stainless steel slab[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2023, 30(11): 2229-2241. |
[2] |
Qing He, Tong-lu Yao, Liu Liu, Xiang-chen Li, Bing Ni, Long-fei Li. An experimental study on RH vacuum chamber with a weir[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2023, 30(10): 1929-1938. |
[3] |
Yi-bo He, Wen-ke Guo, Yi-hong Li, Guang-ming Liu, Xin Cui. Numerical simulation of flow characteristics of side-bottom combined blowing in iron bath reactor[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2023, 30(02): 236-248. |
[4] |
Fang-guan Tan, Sheng-li Jin, Zhu He, Ya-wei Li. Structural optimization and design of purging plug for improving its service performance[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2022, 29(4): 628-635. |
[5] |
Ya-dong Wang, Li-feng Zhang, Wen Yang, Ying Ren. Effect of nozzle type on fluid flow, solidification, and solute transport in mold with mold electromagnetic stirring[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2022, 29(2): 237-246. |
[6] |
Hai-jun Wang, Rui Xu, Hai-tao Ling, Wei Zhong, Li-zhong Chang, Sheng-tao Qiu. Numerical simulation of fluid flow and alloy melting in RH process for electrical steels[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2022, 29(09): 1423-1433. |
|
|
|
|