通道式感应加热中间包钢液流动特性的数值模拟

doi:10.13228/j.boyuan.issn1005-4006.20210052

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (1838 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要通道式感应加热中间包能够有效补偿钢液在浇注过程中产生的温降。钢液流动特性是影响通道式感应加热中间包冶金过程的关键。采用ANSYS软件求解电磁场、流场和温度场控制方程,得到通道式感应加热中间包稳态流场和温度场;在此基础上,求解示踪剂溶质输运方程,得到RTD曲线。数值结果表明,浇注口温度提高20 K;相比于无感应加热的通道式中间包,应用通道式感应加热后,总体平均停留时间延长48 s,总体死区体积分率缩小为21.5%;通道式感应加热中间包的电磁力对钢液的搅拌作用是影响流动形态的主要因素,焦耳热引起的热对流是影响流动形态的次要因素。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	作者相关文章
	张晗
	代传民
	雷洪
	张秀香

关键词 ：中间包, 感应加热, 流场, 温度场, RTD曲线

Abstract：The tundish with the channel type induction heating can effectively compensate for the temperature drop caused by the molten steel during the continuous casting process. The flow characteristics of molten steel are the key factor for the metallurgical process in the tundish with channel type induction heater. The commercial software ANSYS is used to solve the governing equations for electromagnetic field, flow field and temperature field. On the basis of the steady-state flow field and temperature field, the solute transport equation of tracer is solved to obtain the RTD curve. The results show that the temperature of the molten steel at the outlet is 20 K more than that at the ladle shroud in the case of the induction heating. Meanwhile, if the channel induction heating is applied, the overall average residence time is extended by 48 s, and the overall dead zone volume fraction is reduced to 21.5%. Meanwhile, in the tundish with the channel type induction heater, the stirring caused by the electromagnetic force is the main factor affecting the flow pattern of the molten steel, and the thermal convection caused by Joule heat is the secondary factor.

Key words： tundish induction heating flow field temperature field RTD curve

收稿日期: 2021-04-30

引用本文:

张晗, 代传民, 雷洪, 张秀香. 通道式感应加热中间包钢液流动特性的数值模拟[J]. 连铸, 2021, 40(5): 54-59. ZHANG Han, DAI Chuan-min, LEI Hong, ZHANG Xiu-xiang. Numerical simulation for flow characteristics of molten steel in tundish with channel type induction heater. CONTINUOUS CASTING, 2021, 40(5): 54-59.

链接本文:

http://www.chinamet.cn/Jweb_lz/CN/10.13228/j.boyuan.issn1005-4006.20210052 或 http://www.chinamet.cn/Jweb_lz/CN/Y2021/V40/I5/54

[1]	雷洪,张红伟. 结晶器冶金学[M]. 北京:冶金工业出版社,2014.
[2]	萧泽强,朱苗勇. 冶金过程数值模拟分析技术的应用[M]. 北京:冶金工业出版社,2006.
[3]	朱坦华, 周秋月, 任英,等. 二次氧化过程IF钢中间包中夹杂物演变行为[J]. 钢铁, 2020, 55(3): 35.
[4]	杨光维, 陈兆平, 柳向椿. 非钙处理对高等级齿轮钢夹杂物的影响[J]. 钢铁, 2020, 55(4): 40.
[5]	王新华. 中国钢铁工业转型发展时期炼钢科技进步的展望[J]. 炼钢,2019,35(1):1.
[6]	王星,王国连,杨荣光,等. 中间包钢水温度控制研究及优化[J]. 中国冶金,2018,28(1):12.
[7]	陈赛,杨树峰,叶茂林,等.等离子加热对中间包覆盖剂性能的影响[J].连铸,2021(3):1.
[8]	毛斌,陶金明,蒋桃仙. 连铸中间包通道式感应加热技术[J]. 连铸,2008(5):4.
[9]	Mazumdar D. Review, analysis, and modeling of continuous casting tundish systems[J]. Steel Research International,2019,90:1800279.
[10]	Ogasawara T,Yoshikawa N,Taniguchi S,et al. Flow of conducting liquid around two nonconducting particles in DC electromagnetic field and the electromagnetic migration force[J]. Metallurgical and Materials Transactions B,2004,35(5):847.
[11]	刘涛,刘梦静,杨树峰,等. 中间包等离子加热工业试验[J]. 中国冶金,2020,30(10):36.
[12]	Taniguchi S,Brimacombe J K. Application of pinch force to the separation of inclusion particles from liquid steel[J]. ISIJ International,1994,34(9):722.
[13]	Wang Q,Ling B K,Tsukihashi F. Modeling of a thermo-electromagneto-hydrodynamic problem in continuous casting tundish with channel type induction heating[J]. ISIJ International,2014,54(2):311.
[14]	巩彦坤,李高良,韩继强,等.CSP钢水钙铝比对中包塞棒开口度的影响[J].河北冶金,2020(3):14.
[15]	CUI H,LIU Y,LI D X. Fluid flow characterization in asymmetric tundish [J]. ISIJ International,2015,55 (12):2604.
[16]	雷洪,赵岩,鲍家琳,等. 多流连铸中间包停留时间分布曲线总体分析方法[J]. 金属学报,2010,46(9):1109.
[17]	Zong J H,Yi K W,Yoon J K. Residence time distribution analysis by the modified combined model for the design of continuous refining vessel[J]. ISIJ International,1999,39(2):139.