小方坯连铸中间包流场数值模拟与分析

doi:10.13228/j.boyuan.issn1005-4006.20210075

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (6792 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要为了研究不同形状湍流抑制器及不同种类开孔挡墙对中间包流场流动特性及温度分布均一性的影响,以10流小方坯连铸对称双中间包为研究对象,通过Fluent软件对单边5流中间包流场进行数值模拟分析。研究结果表明,湍流抑制器可有效降低注流区湍流的产生,且中间包挡墙的形状和开孔的调整对浇注区各流出口流场及温度场的变化具有较为明显的影响作用。根据数值模拟结果,通过计算云图及指标对比得出了适用于本中间包尺寸及外形条件下的优选控流元件,并由现场实际温度的测量进行了验证。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	作者相关文章
	高宇波
	杨城
	万文华
	肖微
	王敏
	刘宇
	包燕平

关键词 ：中间包, 流场特性, 温度分布, 数值模拟, 控流元件, 小方坯铸机

Abstract：To study the effects of different shapes of turbulence inhibitors and baffle wall with diversion openings on the uniformity and characters of tundish flow as well as temperature field,the flow field of one of the symmetric double tundishes for the ten-strand billet caster was numerically simulated by using fluid dynamics package Fluent. The simulation research results showed that turbulence inhibitors could reduce turblence in injection area of tundish effectively, the flow field and temperature distribution in the pouring area of tundish varied obviously with the adjustment of the shape of baffle wall and its opening. Based on the numerical simulation results of flow image and index chart, optimized flow control devices for this tundish with specific shape and size were achieved, and also be further verified by actual temperature measurement on-site.

Key words： tundish flow field behavior temperature distribution numerical simulation flow control device billet caster

收稿日期: 2021-06-22

引用本文:

高宇波, 杨城, 万文华, 肖微, 王敏, 刘宇, 包燕平. 小方坯连铸中间包流场数值模拟与分析[J]. 连铸, 2021, 40(5): 75-82. GAO Yu-bo, YANG Cheng, WAN Wen-hua, XIAO Wei, WANG Min, LIU Yu, BAO Yan-ping. Numerical simulation and analysis of tundish flow field of billet caster. CONTINUOUS CASTING, 2021, 40(5): 75-82.

链接本文:

http://www.chinamet.cn/Jweb_lz/CN/10.13228/j.boyuan.issn1005-4006.20210075 或 http://www.chinamet.cn/Jweb_lz/CN/Y2021/V40/I5/75

[1]	王建军,包燕平.中间包冶金学[M].北京:冶金工业出版社,2001: 178.
[2]	丁宁,包燕平,陈京生,等.首钢小方坯连铸机中间包数值模拟分析[J].特殊钢,2011,35(5): 8.
[3]	Strandh J, Nakajima K, Eriksson R, et al. Solid inclusion transfer at a steel-slag interface with focus on tundish conditions[J]. ISIJ International, 2005, 45(11): 1597.
[4]	Singh R K, Paul A, Ray A K. Modeling of flow behavior in continuous casting tundish[J]. Scandinavian journal of metallurgy, 2003, 32(3): 137.
[5]	齐新霞,包燕平. 六流方坯中间包流场的物理模拟和冶金效果[J]. 钢铁研究学报,2006(1): 11.
[6]	张弛,包燕平,王敏,等. 四流T型连铸中间包流场优化研究[J].冶金设备,2019(4): 1.
[7]	李东侠,崔衡. 多流中间包钢液流动特性分析方法[J].工程科学学报,2016, 38(1): 41.
[8]	DINGN,BAOY,SUN Q. Optimization of flow control devices in a single-strand slab continuous casting tundish[J]. IJMMM,2011,18(3): 292.
[9]	郑瑞轩,赵立华,姚骋,等. 四流中间包流程影响因素分析与优化[J]. 钢铁,2021,37(1): 63.
[10]	赵丹婷,刘爱强,仇圣桃,等. 带过滤器中间包流场的数学物理模拟和应用[J]. 钢铁,2017,52(1): 27.
[11]	ZHONG L, LI B, ZHU Y. Fluid flow in a four-strand bloom continuous casting tundish with different flow modifiers [J]. ISIJ Internatioanl, 2007,47(1):88.
[12]	张志祥,王德永,冯耀,等. 六流圆坯连铸中间包内流体流动行为的数学模拟[J]. 中国冶金,2011,21(5): 18.
[13]	Merder T, Warzecha M. Optimization of a six-strand continuous casting tundish: industrial measurements and numerical investigation of the tundish modifications[J]. Metallurgical and Materials Transactions B,2012,43(4):856.
[14]	王伟,朱立光,张彩军,等. 双流T-型中间包的流场模拟及其控流结构优化[J]. 连铸,2020(2): 62.
[15]	Lai K Y M,Salcudean M,Tanaka S,et al. Mathematical modeling of flows in large tundish systems in steelmaking[J]. Metallurgical Transactions:Metallurgical Transactions B,1986,17(3):449.
[16]	李永祥,程乃良,冷祥贵,等.优化高拉速板坯连铸中间包控流装置的水模型和数值模拟[J]. 连铸,2007(6):7.