双流板坯连铸中间包结构优化及改造

doi:10.13228/j.boyuan.issn1005-4006.20210088

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (3199 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要中间包作为连铸的关键设备,对保证连铸生产发挥着重要作用。为了减少停浇过程中间包的余钢量,提高金属收得率,以某厂转炉车间双流板坯连铸中间包为模型,利用数值模拟的手段研究中间包流场温度场。根据研究结果,优化设计了中间包结构,为现场中间包结构改造提供优化方案,并介绍了新型中间包的砌筑改造及应用跟踪。改造后的中间包现场应用表明,结构优化能够减少余钢量,使余钢量由16～18 t降至4～6 t,显著提高了金属收得率。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	作者相关文章
	冯孔方
	马建超
	李建伟
	詹侃

关键词 ：连铸中间包, 结构优化, 余钢量, 数值模拟, 停留时间分布

Abstract：As the key equipment in the continuous caster, the tundish plays an important role in ensuring continuous casting production. In order to reduce the residual steel in the tundish during the stop pouring process, improve the metal yield, the two-strand slab continuous casting tundish in a converter workshop is taken as a model, and the temperature field and the flow field in the tundish was studied by numerical simulation. According to the research results, the tundish structure is optimized, which provides the optimization scheme for the tundish structure transformation on site, and the masonry transformation and application tracking of the new tundish are introduced. The results show that optimization of the tundish structure can reduce the amount of residual steel. After optimization, the amount of residual steel is deceased from 16-18 t to 4-5 t. Thus the metal yield is significantly improved.

Key words： continuous casting tundish structure optimization residual steel numerical simulation resident time distribution

收稿日期: 2021-07-26

引用本文:

冯孔方, 马建超, 李建伟, 詹侃. 双流板坯连铸中间包结构优化及改造[J]. 连铸, 2021, 40(5): 83-87. FENG Kong-fang, MA Jian-chao, LI Jian-wei, ZHAN Kan. Structure optimization and transformation of two-strand slab continuous casting tundish. CONTINUOUS CASTING, 2021, 40(5): 83-87.

链接本文:

http://www.chinamet.cn/Jweb_lz/CN/10.13228/j.boyuan.issn1005-4006.20210088 或 http://www.chinamet.cn/Jweb_lz/CN/Y2021/V40/I5/83

[1]	陈玉辉,刘吉刚. 中间包优化对板坯连铸钢水洁净度的影响分析[J]. 连铸,2019 (3): 51.
[2]	李少翔,铁占鹏,郑宝安,等. 三流大方坯连铸中间包流场优化数值模拟研究[J]. 连铸,2019 (5): 47.
[3]	田永华,包燕平,李怡宏,等. 80 t两流板坯连铸中间包挡墙结构优化研究[J]. 钢铁钒钛,2013,34(2):67.
[4]	陈俊俊,史彧宏, 武文斐,等. 连铸中间包技术改造与多孔控流挡墙的优化设计[J]. 冶金能源,2007,26(5):22.
[5]	苑品,包燕平,崔衡,等. 高品质IF钢连铸中间包降低残钢量的水模型研究[J]. 北京科技大学学报,2011,33(增刊1):1.
[6]	青靓,李树森,崔衡. 连铸中间包降低残钢量的水模型研究[J]. 铸造技术,2017,38(9):2193.
[7]	王卫华,赵新宇,刘洋,等. 连铸末期尾坯拉速的优化[J]. 炼钢,2017,33(2):43.
[8]	徐向阳,马勇,张晓军,等. 降低大方坯中间包临界液面高度工艺研究[J].鞍钢技术,2015 (2):20.
[9]	王爱东,徐海芳,傅秋华,等. 薄板坯连铸中间包流场数值模拟与优化[J]. 连铸,2020 (4): 1.
[10]	王伟,朱立光,张彩军. 双流T-型中间包的流场模拟及其控流结构优化[J]. 连铸,2020 (2): 62.
[11]	曾俊,王波,张捷宇,等. 中间包底吹气正交试验数值模拟研究[J]. 连铸,2017 (4):6.
[12]	张利君,宁林新,刘金刚,等. 板坯中间包控流装置优化的数值模拟[J]. 连铸,2014 (5): 13.
[13]	樊俊飞,朱苗勇,张清朗,等. 六流连铸中间包内流动与传热耦合过程的数值模拟及控流装置优化[J]. 金属学报,1999,35(11): 1191.
[14]	程子建,成东全,程树森,等. 酒钢板坯中间包等温钢液流场的数值模拟[J]. 钢铁研究学报,2008,20(2): 60.
[15]	Sahai Y,Emi T. Melt flow characterization in continuous casting tundishes[J]. ISIJ International,1996,36(6):667.
[16]	Strandh J,Nakajima K,Eriksson R,et al. Solid inclusion transfer at a steel-slag interface with focus on tundish conditions[J]. ISIJ International,2005,45(11):1597.