双辊薄带铸轧3%取向硅钢凝固组织模拟

doi:10.13228/j.boyuan.issn1005-4006.20230030

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (1758 KB) HTML (0 KB)
Export: BibTeX | EndNote (RIS)

Abstract When thin strip casting and rolling oriented silicon steel, columnar crystals are easily formed in the structure of the casting strip, which are easily elongated into banded structures in subsequent processing and heat treatment processes, hindering the development of secondary recrystallization and reducing the electromagnetic properties of oriented silicon steel. In order to optimize the casting and rolling process parameters, this article uses the CAFE module in ProCAST and adopts orthogonal experiments to study the influence of various process parameters on the microstructure of the cast strip during the casting and rolling process of3% oriented silicon steel. The results show that the pulling speed has the greatest impact on the height of the Kiss point. As the roller speed increases, the height of the Kiss point decreases. When the pulling speed changes from 0.3 m/s to 0.7 m/s, the height of the Kiss point changes from 35.4 mm to 13.0 mm. The casting temperature has the greatest impact on the proportion of columnar crystals. As the casting temperature increases, the proportion of columnar crystals increases. When the casting temperature changes between 1 502 ℃ and 1 542 ℃, the proportion of columnar crystals varies between 14.4% and 81.3%. The casting temperature has the greatest impact on the average grain size. The higher the casting temperature, the larger the average grain size. The average grain size varies from 187.3 μm to 346.4 μm when the casting temperature changes from 1 502 ℃ to 1 542 ℃. In summary, the optimal parameters are as follows: casting temperature 1 502 ℃, casting speed 0.7 m/s, molten pool height 150 mm, corresponding Kiss point height 15.3 mm, columnar crystal proportion 18.3%, and average grain size 193.1 μm.

Key words： oriented silicon steel twin roll thin strip casting and rolling numerical simulation solidified tissue process parameter

Received: 17 April 2023

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	GUO Zhi-hong
	LIU Yu
	LU Su-ling
	ZHENG Ya-xu
	ZHU Li-guang
	SUN Hui-lan

Cite this article:

GUO Zhi-hong,LIU Yu,LU Su-ling等. Simulation of solidification structure of 3% oriented silicon steel produced by twin roll strip casting and rolling[J]. CONTINUOUS CASTING, 2023, 42(3): 55-61.

URL:

http://www.chinamet.cn/Jweb_lz/EN/10.13228/j.boyuan.issn1005-4006.20230030 OR http://www.chinamet.cn/Jweb_lz/EN/Y2023/V42/I3/55

[1]	蔡常青.双辊薄带连铸连轧技术的现状与展望[J].福建冶金,2022,51(1):50.
[2]	PARK J Y, OH K H, RA H Y. The effects of superheating on texture and microstructure of Fe-4.5wt%Si steel strip by twin-roll strip casting [J]. ISIJ International, 2001,41(1): 70.
[3]	王洋. 薄带连铸取向硅钢成分设计与组织织构调控机理的研究[D]. 沈阳:东北大学, 2017.
[4]	夏强强, 李莉娟, 刘立华, 等. 取向硅钢生产工艺研究进展[J]. 材料导报, 2010, 24(5): 4.
[5]	CHEN H Y, HUANG S J. Adaptive fuzzy sliding-mode controller for control of the strip casting process[J]. Proceedings of the Institution of Mechanical Engineers Part I Journal of Systems and Control Engineering, 2010, 1(6): 1.
[6]	LI J T, XU G M, YU H L, et al. Optimization of process parameters in twin-roll strip casting of an AZ61 alloy by experiments and simulations[J]. International Journal of Advanced Manufacturing Technology, 2015, 76(9/10/11/12): 1769.
[7]	丁培道, 蒋斌, 杨春楣, 等. 薄带连铸技术的发展现状与思考 [J]. 中国有色金属学报, 2004, 14(1): 5.
[8]	LEE J G, LEE H, OH Y S, et al. Continuous fabrication of bulk amorphous alloy sheets by twin-roll strip casting [J]. Intermetallics, 2006, 14(8/9): 987.
[9]	OHLER C, ODENTHAL H J, PFEIFER H. Physical and numerical simulation of fluid flow and solidification at the strip casting process [J]. Steel Research International, 2003, 74(11/12): 739.
[10]	XU Z Q, MENG Z R, DU F S, et al. Current situation and prospect of twin-roll strip casting process numerical simulation [J]. Journal of Yanshan University, 2014,38(2):95.
[11]	张冬晓, 常庆明, 潘成刚, 等. 双辊薄带铸轧凝固组织数值模拟[J]. 特种铸造及有色合金, 2015, 35(6): 585.
[12]	李逸尘,毛宽民.基于PROCAST软件的铸锭形状仿真分析[J].河南师范大学学报(自然科学版),2022,50(2): 86.
[13]	马恺.Q235异型坯连铸工艺参数对糊状区长度的影响[J].河北冶金,2020(12): 25.
[14]	艾迪. 焊接用C65600铜合金上引连铸数值模拟与工艺参数优化[D].南昌:江西理工大学,2020.
[15]	刘义, 张炯明, 宋炜, 等. 6.5%Si高硅钢铸锭凝固组织的 CAFE 法模拟研究[J]. 功能材料, 2014, 45(19): 19089.
[16]	徐益龙, 孙济鹏, 潘湾萍, 等. 低碳钢薄带双辊连铸凝固过程的数值模拟 [J]. 上海金属, 2020, 42(2): 7.
[17]	薛然. 硅钢薄带双辊铸轧过程的数值模拟研究[D]. 大连:大连理工大学, 2016.
[18]	刘文文, 黄华贵. 双辊铸轧热-流-组织耦合模拟及铸轧区组织精细分析 [J]. 材料热处理学报, 2021, 42(7): 8.
[19]	陈晋. 基于胞元自动机方法的凝固过程微观组织数值模拟[D]. 南京:东南大学, 2005.
[20]	许庆彦, 柳百成. 铸造合金凝固组织的计算机模拟与预测 [J]. 稀有金属材料与工程, 2003,32(6): 401.
[21]	于艳梅. 过冷熔体中枝晶生长的相场法数值模拟 [J]. 西安:西北工业大学, 2002.
[22]	LIU D R, ZIMMERMANN G, STURZ L, et al. CAFE simulation of columnar-to-equiaxed transition in Al-7wt%Si alloys directionally solidified under microgravity [J]. IOP Conf. Series: Materials Science and Engineering,2014,64: 253.
[23]	WANG J L, WANG F M, LI C R, et al. Simulation of solidification processes of 9SMn28 free-cutting steel based on a CAFE Method [J]. Journal of University of Science and Technology Beijing, 2010, 32(3): 325.
[24]	宋炜, 张炯明, 王顺玺. 基于实验与3D-CAFE法的高硅钢铸锭凝固行为 [J]. 工程科学学报, 2017, 39(3): 9.
[25]	王金龙, 赖朝彬, 王福明, 等. CAFE模型机理及应用 [J]. 钢铁研究学报, 2009, 21(10): 4.
[26]	RAPPAZ M, GANDIN C A. Probabilistic modelling of microstructure formation in solidification processes[J]. Acta Metallurgica et Materialia, 1993, 41(2): 345.