四流大圆坯中间包挡墙优化

doi:10.13228/j.boyuan.issn1005-4006.20230070

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (0 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract In order to solve the problem that the quality of the casting billet in the middle two strands is significantly lower than that in the edge two strands during poor production conditions in a steel plant, improve the consistency of each strand in the tundish, and reduce the proportion of dead zones in the tundish, we designed three methods on the same retaining wall, and obtained the time residence distribution (RTD) curves of each scheme through water model physical experiments. After analyzing the RTD curves, the corresponding proportions of dead zone, piston flow zone, and fully mixed flow zone for each scheme were obtained. At the same time, taking into account the peaks of the RTD curve and the consistency between various strands, the optimal production plan was obtained. The research results indicate that the B1 scheme with a single hole on the side has the best flow field, with an aperture of 140 mm and a vertical angle of 20°. The consistency between its two strands is very good, with a dead zone ratio of 19.95%, and the RTD curve has no peaks or double peaks.

Key words： tundish structural optimization retaining wall dead zone ratio RTD curve

Received: 28 July 2023

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	JIANG Ye
	LI Ming
	WU Jianyong
	MAO Naixu
	SONG Sicheng
	SUN Yanhui

Cite this article:

JIANG Ye,LI Ming,WU Jianyong等. Optimization of retaining wall for four stream large round billet tundish[J]. CONTINUOUS CASTING, 2024, 43(1): 32-37.

URL:

http://www.chinamet.cn/Jweb_lz/EN/10.13228/j.boyuan.issn1005-4006.20230070 OR http://www.chinamet.cn/Jweb_lz/EN/Y2024/V43/I1/32

[1]	王汝栋,苏旺,崔衡,等.基于F曲线的中间包流场优化[J].工程科学学报,2020,42(增刊1):95.
[2]	李成江,张正伟.中间包钢水净化技术[J].河北冶金,2023(9):46.
[3]	牛增辉,李杰,俞学成,等.高液位浸入式中间包快换工艺[J].河北冶金,2022(3):54.
[4]	王家辉,张华,方庆,等.顶旋型湍流抑制器优化中间包流场的物理模拟[J].钢铁,2023,58(2):72.
[5]	陈希青,肖红,王璞,等.双通道感应加热中间包的三维磁流热耦合模型[J].钢铁,2021,56(6):48.
[6]	马钰,唐海燕,张硕,等.通道式感应加热五流中间包流场的水力学模拟[J].钢铁,2020,55(11):57.
[7]	李玉峰,孙彦辉,宋思程,等.六流中间包挡墙优化的数值模拟和工业实践[J].特殊钢,2022,43(3):7.
[8]	郭达.十流小方坯连铸机双中间包流场的优化设计[J].宽厚板,2023,29(3):28.
[9]	宋丽娜,铁占鹏.非对称中间包常用控流装置冶金效果的数值模拟[J].钢铁研究学报,2023,35(6):692.
[10]	左小坦,赵立,张亚兵,等.气幕挡墙对中间包流场和夹杂物去除的影响[J].连铸,2023(1):24.
[11]	谭文萱,孙彦辉,宋思程,等.七流中间包流场的优化与模拟[J].钢铁研究学报,2023,35(6):682.
[12]	吴金强,杨树峰,李京社,等.三流中间包结构优化物理模拟[J].中国冶金,2019,29(11):39.
[13]	李小松,唐海燕,胡群,等.非对称控流结构中间包流场一致性的物理模拟[J].中国冶金,2020,30(10):28.
[14]	李少翔,铁占鹏,郑宝安,等.三流大方坯连铸中间包流场优化数值模拟研究[J].连铸,2019(5):47.
[15]	王锦,刘宇航,刘威,等.基于中间包冲击区的流场优化[J].中国冶金,2023,33(4):97.
[16]	熊洪进,陈列,董贵文.圆坯连铸机中间包流场流动特性研究[J].特钢技术,2021,27(1):1.
[17]	王阳,李小明,朱佳雨,等.注流孔结构对中间包流场影响的物理模拟[J].过程工程学报,2023,23(2):235.
[18]	SONG S, SUN Y, AN H. Numerical modeling of grade mixing and inclusion entrapment in eight strand billet tundish[J]. Metallurgical Research & Technology, 2023, 120(1):1.
[19]	SIDDIQUI M, JHA P K. Effect of inflow rate variation on intermixing in a steelmaking tundish during ladle change-over[J]. Steel Research International, 2016, 87(6): 733.
[20]	秦绪锋,程常桂,李阳,等.上水口环形吹氩对中间包内渣眼形成的影响[J].钢铁,2019,54(08):107.
[21]	陈远清,仇圣桃.T形中间包新型控流装置的模拟及试验[J].钢铁,2018,53(7):45.
[22]	吴光辉,唐海燕,肖红,等.通道式感应加热7流中间包流场的物理模拟[J].钢铁,2017,52(11):20.
[23]	肖红,徐辉,何浩,等.基于数值模拟的五流感应加热中间包流场优化[J].中国冶金,2021,31(1):14.
[24]	张杰,郑淑国,朱苗勇.加热功率对感应加热中间包影响的数值模拟[J].中国冶金,2021,31(10):68.
[25]	全齐,屈天鹏,秦俊山,等.连铸中间包内流体运动形态模型分析研究[J].炼钢,2023,39(4):37.
[26]	陈宏亮,刘珍童,周秋月,等.中间包内钢液流动和二次氧化的数值模拟[J].中国冶金,2023,33(7):40.
[27]	田宝生,方庆,王家辉,等.气幕挡墙技术优化双流中间包流场的物理模拟[J].连铸,2023(2):19.
[28]	马金磊,牛帅,唐海燕,等.帘线钢连铸7流中间包钢水流动特性及各流一致性研究[J].钢铁研究学报,2023,35(6):671.
[29]	姜学锋,时朋召,王玉平,等.单流厚板坯中间包物理模拟研究和应用[J].特殊钢,2022,43(1):16.
[30]	王凯民,唐海燕,肖红,等.六流双通道感应加热中间包钢水流动控制[J].中国冶金,2022,32(2):84.
[31]	高江,刘青,李权辉,等.挡墙设计对四流T型中间包钢液流动行为的影响[J].连铸,2022(3):11.