欢迎访问《钢铁研究学报(英文版)》官方网站!今天是

2023年, 第30卷, 第09期 刊出日期:2023-09-25
  

  • 全选
    |
    综述
  • Rui-fang Wang, Bo Zhang, Cheng-jun Liu, Mao-fa Jiang
    钢铁研究学报(英文版). 2023, 30(09): 1661-1674.
    https://doi.org/10.1007/s42243-023-00954-0
    摘要 ( )   可视化   收藏
    Basic oxygen steelmaking (BOS) is the most frequently used method to produce molten steel, which is being developed to meet the requirements of being safe, efficient, clean, and intelligent. During the BOS process, splashing events cause undesirable consequences, such as casualties, low efficiency, environmental pollution, and uncontrollable operation. The causes of three types of splashing (eruptive, foaming, and metallic splashing) were unraveled and it is concluded that inappropriate foaming is the root cause of splashing. A variety of monitoring techniques for splashing have been developed to measure real-time slag foaming in a basic oxygen furnace (BOF). The audiometry technique with flexible operation and high accuracy was comprehensively introduced with a practical application. Based on the formation mechanisms, the countermeasures for the three types of splashing were proposed to regulate slag foaming in a BOF by integrating diverse measures in terms of raw materials, slag forming, blowing pattern, and the use of splashing regulating agents. Future work should emphasise an automatic action for these prevention measures in response to the splashing risk from the monitoring technology, promoting the progress of intelligent steelmaking.
  • 论著
  • Bin Li, Heng Zhou, Jian Huang, Zong-wang Zhang, Xue-feng She, Jian-fang Wang, Sheng-li Wu, Ming-yin Kou
    钢铁研究学报(英文版). 2023, 30(09): 1675-1686.
    https://doi.org/10.1007/s42243-022-00896-z
    摘要 ( )   可视化   收藏
    Mauritanian iron ore powder (OM) has advantages of high iron grade, low aluminum content, and low loss on ignition, which can be used as a new mineral to replace low alumina limonite that has been exhausted in Australia. However, it will have a certain negative impact on sintering because of its high SiO2 content. The mechanism of SiO2 content affecting the sintering behavior was first studied through FactSage 7.2. Then, the liquid fluidity, penetration, and high-temperature performance of different iron ore powders were compared. Finally, the optimization of ore blending structure was studied by the micro-sintering method and the sinter pot test. The results show that the increase in SiO2 content can reduce the assimilation temperature. The low penetration of OM can lead to an increase in the amount of liquid, and the high SiO2 content of OM increases the viscosity of the liquid phase. What is more, the increase in SiO2 also increases the formation of silicate and fayalite phase and inhibits the formation of silico-ferrite of calcium and aluminum (SFCA). To optimize ore blending structure, OM and the low SiO2 powder OD from Australia were used together, which improves the content of SFCA by 2.04% and decreases the contents of calcium silicate and fayalite by 0.63% and 4.99%, respectively. The results of the sinter pot test indicated that the properties of sinter have been improved.
  • Yong-li Jin, Jin-tao Jiang, Hong-xing Dai, Xu-dong Zhang, Zeng-wu Zhao
    钢铁研究学报(英文版). 2023, 30(09): 1687-1700.
    https://doi.org/10.1007/s42243-023-00912-w
    摘要 ( )   可视化   收藏
    The use of low-grade, refractory and composite paragenetic mineral resources is necessary for overcoming the shortage of iron ore resources in China. As a solution to the treatment of such iron ores, the direct reduction of carbon-bearing pellets can ensure complete iron removal and the effective enrichment of other high-value elements. Thus, this technology enjoys a broad application prospect. However, there are several problems with low-temperature reduction, such as low iron ore reaction efficiency, long reaction time, and high energy consumption. To improve the low-temperature carbothermic reduction efficiency of iron ores, a static magnetic field with magnetic induction intensity of 1.0 T was introduced. An isothermal reduction experiment was conducted at 1223 K to study the low-temperature self-reduction characteristics of carbon-bearing pellets of Bayan Obo lean iron ores in the static magnetic field. Also, the acting mechanism of the magnetic field was explored from the perspective of the reduction process, reaction efficiency, phase composition, microstructure changes, and dynamic behavior of iron ores. The results showed that the magnetic field can increase the low-temperature reduction rate of carbon-bearing pellets of Bayan Obo lean iron ores. Under the conditions of reduction temperature of 1223 K, magnetic induction intensity of 1.0 T, and reduction time of 60 min, the reduction degree was 92.42%, 1.65 times that without a magnetic field. The magnetic field promoted the replacement of Ca2+ and Fe2+, so that the hard-to-reduce iron-bearing silicates were reduced in the order of Fe2SiO4 →(Ca, Na)FeSiO4 → FeO → Fe. The magnetic field enabled loose minerals, more pores and cracks, and changes in the growth morphology and distribution position of metallic iron. Compared with the case under the non-magnetic condition, the metallic iron precipitated from the slag phase in a foliated shape, separated from the matrix iron oxides, and grew up at the junction of the slag phase and coke. The magnetic field significantly increased the interfacial chemical reaction rate of the carbothermic reduction of iron ores and reduced the internal diffusion resistance of gas in the product layer. Specifically, the interfacial chemical reaction rate increased by 138% and the internal diffusion coefficient increased by 309%. Therefore, the effect of the magnetic field on the internal diffusion resistance was the main cause for strengthening the low-temperature reduction of iron ores.
  • Xiao-dong Ping, Hai-feng Wang, Feng Wang, Xin-yu Wan, Zhi-wei An, Jian-lei Pan
    钢铁研究学报(英文版). 2023, 30(09): 1701-1713.
    https://doi.org/10.1007/s42243-022-00900-6
    摘要 ( )   可视化   收藏
    Municipal sludge is produced in large amounts and is difficult to treat. Incineration is the most direct and thorough treatment method. In order to study the feasibility of sintering for municipal sludge treatment, the municipal sludge reforming process was studied under high-temperature oxidation conditions. The results showed that the sludge reforming process could be divided into four stages: the precipitation and evaporation of adsorbed water, the precipitation and combustion of the volatile, the combustion of the residual volatile and solid carbon, and the decomposition of salts and the melting of sludge. An increase in the heating rate resulted in more intense sludge combustion and improved the sludge reaction capacity and combustion performance. After burning at 1300 ºC, Si, Ca, Mg, Al, K, Na, and Cu formed new phases and entered the slag. 75% of P remained in the slag. 80% of the S formed SO2 and entered the flue gas. Cl formed gaseous chlorides like HCl upon combustion and entered the flue gas. As sintering is a feasible method for treating municipal sludge, care must be taken to limit the amount of P that ends up in the ore.
  • Ji-wei Bao, Man-sheng Chu, Zheng-gen Liu, Wei Lv, Dong Han, Li-feng Zhang
    钢铁研究学报(英文版). 2023, 30(09): 1714-1731.
    https://doi.org/10.1007/s42243-023-00910-y
    摘要 ( )   可视化   收藏
    Iron carbon agglomerates (ICA) are the composite burden for low-carbon blast furnace (BF) ironmaking. In order to optimize the reactivity of ICA according to the evolution characteristics of ICA in the BF smelting process, the evolution behavior and mechanism of different reactive ICA under simulated BF smelting conditions were studied. The results show that the existence of more sillimanite and aluminosilicate and less active sites of metallic iron will weaken gasification reaction and carburization ability of ICA-1 (containing 10% iron ore). It weakens the promoting effect of ICA-1 on the reduction, softening, and melting of ferrous burdens and the dripping of slag-iron. The aluminosilicate with a high melting point decreases, the low melting point slag phase and Fe–Si alloy increase, and many active sites of metallic iron exist, which strengthen the gasification reaction and carburization ability of ICA-2 (containing 30% iron ore). The promoting effect of ICA-2 on the reduction, softening, and melting of ferrous burdens and the dripping of slag-iron is significantly improved. The gasification reaction capacity of ICA-3 (containing 35% iron ore) is reduced, and the improvement in ICA-3 on the softening–melting performance of mixed burdens is reduced. The appropriate proportion of iron ore in ICA is about 30%.
  • Shuai Wang, Ying Jiang, Yu-feng Guo, Feng Chen, Ling-zhi Yang, Zhuang Yang, Guang Li
    钢铁研究学报(英文版). 2023, 30(09): 1732-1742.
    https://doi.org/10.1007/s42243-022-00873-6
    摘要 ( )   可视化   收藏
    High alumina slag is widely found in pyrometallurgical extractions of ferronickel, ferrochromium, and platinum group metals. The effects of MgO, Al2O3, and CaO/SiO2 on the sulfur distribution ratio between high-alumina CaO–SiO2–MgO–Al2O3 slag and carbon-saturated iron were investigated. The slag consisted of Al2O3 content in the range of 27.61–40.00 wt.%, CaO/SiO2 ratio of 0.8–1.1, and MgO content of 8–16 wt.%. The theoretical liquid areas of CaO–SiO2–MgO–Al2O3 slag were analyzed through the phase diagrams. The sulfur distribution ratio was measured via the slag–metal equilibrium technique at 1500 ºC. It was observed that the sulfur distribution ratio increased with higher MgO content and higher CaO/SiO2 ratio largely due to the increase in free O2- ions and the decrease in activity coefficient of sulfur ion in slag, but slightly decreased with the increasing Al2O3 content because of the decrease in free O2-.
  • Wen-wen Zhang, Wan Zheng, Wen Yan, Guang-qiang Li
    钢铁研究学报(英文版). 2023, 30(09): 1743-1754.
    https://doi.org/10.1007/s42243-022-00889-y
    摘要 ( )   可视化   收藏
    The ceramic filter in continuous casting tundish can effectively improve the cleanliness of high-performance steel by regulating tundish flow field to promote the removal of inclusions and adsorbing or blocking fine inclusions in the molten steel into the mold. The interaction between microporous magnesia refractories used as tundish filter and molten interstitial- free (IF) steel at 1873 K was investigated to reveal the formation mechanism of their interface layer and its effect on steel cleanliness by laboratory research and thermodynamic calculations. The results show that the magnesium–aluminum spinel layer at the interface between the molten IF steel and the microporous magnesia refractories is formed mainly by the reaction of MgO in the refractory with the [Al] and [O] in the molten steel, significantly reducing the total O content, the size and amount of inclusions of the molten steel. In addition, the interparticle phases of microporous magnesia refractories at high temperature can adsorb Al2O3 and TiO2 inclusions in the molten steel into interparticle channels of the refractories to form high melting point spinel, impeding the further penetration of the molten steel. As a result, the consecutive interface layer of high melting point spinel between microporous magnesia refractories and molten steel can improve the cleanliness of the molten steel by adsorbing inclusions in the molten steel and avoid the direct dissolution of refractories of the tundish ceramic filter immersed in the molten steel, increasing their service life.
  • Chen Wang, Wei Tang, Jiang-shan Zhang, Jun-xiong Huang, Kun-rui Shen, Jun Chen, Qing Liu
    钢铁研究学报(英文版). 2023, 30(09): 1755-1768.
    https://doi.org/10.1007/s42243-023-00941-5
    摘要 ( )   可视化   收藏
    The laboratory experiments, thermodynamic analysis, dynamic analysis, and industrial trials were carried out to investigate the influence of refining slag on the evolution and removal of oxide inclusions in 55SiCrA spring steel. The reduction in basicity and Al2O3 content in refining slag can reduce the [Al]s content in the molten steel, which is conducive to the control of the low melting point of inclusions. However, the refining slag with excessively low basicity transfers the oxygen element to molten steel and increases the Al2O3 content in inclusions, which is harmful to the control of inclusions. According to the chemical compositions of inclusions and refining slag in laboratory experiments, their physical parameters were calculated. The maximum separation ratio and the moving time of inclusions to reach the maximum separation ratio (tmax) of inclusions under different laboratory experimental conditions were studied. The maximum separation ratio of inclusions is positively correlated with the overall wettability (coshIMS) among the slag, steel, and inclusions. The maximum separation ratio of inclusions obtained by laboratory experiments is between 85% and 91%. The tmax decreases with the decline in basicity and Al2O3 content of refining slag, but excessively low basicity will increase the tmax. The basicity of refining slag in the range of 0.88–0.97 and the content of Al2O3 less than 6% is not only conducive to reducing the content of Al2O3 and the melting point of inclusions but also beneficial to removing the inclusions to the slag. The slag system shows good metallurgical results in industrial trials.
  • Zhi-yuan Liu, Li-hao Zhang, Cheng Ji, Miao-yong Zhu, Chong-jun Wang
    钢铁研究学报(英文版). 2023, 30(09): 1769-1781.
    https://doi.org/10.1007/s42243-023-00940-6
    摘要 ( )   可视化   收藏
    In order to describe the thermal–mechanical behavior of the ship plate steel continuous casting slab during solidification end heavy reduction (HR) process accurately, its constitutive behavior was investigated by a single-pass thermal compression experiment. According to the deformation features of wide thick continuous casting slab with HR, the simulation temperature ranged from 1173 to 1573 K with strain rates of 0.0001, 0.001, 0.01 and 0.1 s-1. Three different constitutive models, the modified Johnson–Cook (JC) model, the modified Zerilli–Armstrong (ZA) model and the Arrhenius model, were established according to the obtained true stress–strain curves. The average relative error of the modified JC model, the modified ZA model and the Arrhenius model are 10.82%, 9.96% and 6.21%, respectively. Considering the obvious softening effect of the flow curve at a low strain rate, the secondary softening factor under the interaction of low strain rate and the temperature was introduced in the original Arrhenius model. Compared to the Arrhenius model, the modified Arrhenius model error decreased from 6.21% to 4.73%.
  • Shu-zong Chen, Cheng Jia, Chang-chun Hua, Jia-qiang Chen
    钢铁研究学报(英文版). 2023, 30(09): 1782-1791.
    https://doi.org/10.1007/s42243-023-00926-4
    摘要 ( )   可视化   收藏
    An adaptive command filter control strategy was proposed to realize the asymptotic tracking of the roll speed, which successfully suppressed torsional vibration for the main drive system of the rolling mill with nonlinear friction, nonlinear damping, current harmonic, time-varying stiffness and unknown disturbance. A finite time predetermined performance method was proposed, so that the speed tracking error of the main transmission system was always constrained in the performance function and converged to its minimum boundary within the specified time. Based on the adaptive estimation of harmonic amplitude, the torque control law of the motor was obtained by using the filter backstepping method, which prevented the torsional vibration of the system caused by the input fluctuation and avoided the complexity explosion of the controller design, and the stability of the closed-loop system was strictly proved by the Lyapunov theory. The actual numerical simulation verified the effectiveness of the proposed control strategy.
  • Yu-jie Liu, Shen Wang, Jie-bin Qi, Xiao-qiang Yan
    钢铁研究学报(英文版). 2023, 30(09): 1792-1802.
    https://doi.org/10.1007/s42243-022-00886-1
    摘要 ( )   可视化   收藏
    Vibration issues of a five-stand tandem cold rolling mill were found in the steel production practice, and the experimental observation and numerical analysis indicated that the vibrations were related to the back-up roll bearing. The results were validated by replacing the back-up roll bearing with the new bearing resulting in 30% decline in vibration amplitude. Models describing the four-row cylindrical roller bearing and the vertical system of the cold rolling mill including the bearing were established. Moreover, the mechanisms of periodic excitation and amplified vibrations of fault-free bearing were explained theoretically, along with the analysis of bifurcation behaviors of the motion states of the roller bearing and rolling mill system. It is found that the energy transmitted between vibrations with different frequencies if multiple excitation frequencies in the rolling mill system were close.
  • Ze-dong Wu, Xiao-chen Wang, Quan Yang, Dong Xu, Jian-wei Zhao, Jing-dong Li, Shu-zong Yan
    钢铁研究学报(英文版). 2023, 30(09): 1803-1820.
    https://doi.org/10.1007/s42243-022-00894-1
    摘要 ( )   可视化   收藏
    In the traditional rolling force model of tandem cold rolling mills, the calculation of the deformation resistance of the strip head does not consider the actual size and mechanical properties of the incoming material, which results in a mismatch between the deformation resistance setting and the actual state of the incoming material and thus affects the accuracy of the rolling force during the low-speed rolling process of the strip head. The inverse calculation of deformation resistance was derived to obtain the actual deformation resistance of the strip head in the tandem cold rolling process, and the actual process parameters of the strip in the hot and cold rolling processes were integrated to create the cross-process dataset as the basis to establish the support vector regression (SVR) model. The grey wolf optimization (GWO) algorithm was used to optimize the hyperparameters in the SVR model, and a deformation resistance prediction model based on GWO–SVR was established. Compared with the traditional model, the GWO–SVR model shows different degrees of improvement in each stand, with significant improvement in stands S3–S5. The prediction results of the GWO–SVR model were applied to calculate the head rolling setting of a 1420 mm tandem rolling mill. The head rolling force had a similar degree of improvement in accuracy to the deformation resistance, and the phenomenon of low head rolling force setting from stands S3 to S5 was obviously improved. Meanwhile, the thickness quality and shape quality of the strip head were improved accordingly, and the application results were consistent with expectations.
  • Jian-zhao Cao, Yu-xia Wang, Shao-wen Huang, Chang-tao Wang
    钢铁研究学报(英文版). 2023, 30(09): 1821-1833.
    https://doi.org/10.1007/s42243-023-00936-2
    摘要 ( )   可视化   收藏
    The shearing line is the key to improve the quality and efficiency of heavy plates. A model of contour recognition and intelligent shearing strategy for the heavy plate was proposed. Firstly, multi-array binocular vision linear cameras were used to complete the image acquisition. Secondly, the total length of the steel plate after cooling was predicted by back propagation neural network algorithm according to the contour data. Finally, using the scanning line and a new camber description method, the shearing strategy including head/tail irregular shape length and rough dividing strategy was calculated. The practical application shows that the model and strategy can effectively solve the problems existing in the shearing process and can effectively improve the yield of steel plates. The maximum error of detection width, length, camber, and the length of the irregular deformation area at the head/tail of the plate are all less than 5 mm. The correlation coefficient of the length prediction model based on the back propagation neural network is very high. The reverse ratio result of edge cutting failure using the proposed rough dividing strategy is 1/401 = 0.2%, which is 2% higher than that by human.
  • Wen-feng Gu, Jiang Diao, Rui-xin Hu, Wen-sun Ge, Wen-feng Tan, Hong-yi Li, Bing Xie
    钢铁研究学报(英文版). 2023, 30(09): 1834-1842.
    https://doi.org/10.1007/s42243-022-00883-4
    摘要 ( )   可视化   收藏
    In order to effectively utilize the resources and energy of molten steel slag, the variation of precipitation phase and specific heat of air quenched steel slag (AQSS) particles during continuous cooling process was investigated by FactSage and thermogravimetry differential scanning calorimetry. The cooling and solidification process of molten AQSS particles was simulated by Fluent. The microstructure changes in AQSS particles in solidification process were analyzed using an ultrahigh temperature laser confocal microscope and a scanning electron microscope. The results indicated that in the cooling process of molten AQSS particles, the precipitation of Ca2Fe2O5 resulted in the largest change of specific heat. Under the condition of slow cooling, the cooling rate is more obviously affected by specific heat. When the initial air velocity was 300 m s-1, there was the highest temperature difference in AQSS particles during cooling process. What is more, the compactness of the boundary region of AQSS particles was obviously better than that of its central region.
  • Tian-yu Zhang, Ling-yu Wang, Yu Wang, Jun Hu, Hong-shuang Di, Wei Xu
    钢铁研究学报(英文版). 2023, 30(09): 1843-1853.
    https://doi.org/10.1007/s42243-022-00841-0
    摘要 ( )   可视化   收藏
    Low-temperature ausforming (LT-AF) prior to bainitic transformation leads to a noticeable acceleration of bainitic transformation kinetics; however, the effect of LT-AF on the retained austenite (RA) features and the resulting mechanical properties is still unclear. LT-AF was applied to ultrahigh-strength bainitic steel before austempering. The deformation behavior and the resulting dislocation substructures were investigated by thermomechanical simulator and transmission electron microscopy (TEM). The planar dislocation structures produced during deformation at 350 °C accelerate the bainitic transformation kinetics during isothermal holding. The effect of LT-AF on the bainitic transformation kinetics and the features of RA was elucidated via dilatometer measurement, TEM, scanning electron microscopy, and X-ray diffraction. It is observed that LT-AF not only retains more RA content but also facilitates improved RA stability. This trend is mainly due to the large amounts of planar dislocations in RA and bainitic laths inherited from undercooled austenite caused by LT-AF, the decrease in bainitic sheaves size, and the increase in filmy RA content compared to the sample without ausforming. A large fraction of filmy RA with high stability and the refinement of bainitic sheaves obtained by LT-AF remarkably enhance the strain hardening capacity and achieve significantly better ductility compared to the directly austempered sample.
  • Shou-hui Li, Jing Li, Jie Zhang, Cheng-bin Shi
    钢铁研究学报(英文版). 2023, 30(09): 1854-1861.
    https://doi.org/10.1007/s42243-022-00851-y
    摘要 ( )   可视化   收藏
    Two ingots of 4Cr13 martensitic stainless steel with different nitrogen contents, 0.023 and 0.121 mass%, were produced by vacuum induction furnace and electroslag remelting. The microstructure and the microsegregation of the electroslag remelting ingot were analyzed by optical microscopy, scanning electron microscopy and electron microprobe analysis. Thermo-Calc software was used to calculate the nitrogen solubility changes during solidification of high nitrogen martensitic stainless steel and the equilibrium and non-equilibrium phase diagrams of 4Cr13 steel with different nitrogen contents. The solubility of nitrogen in 4Cr13 steel reached the lowest value of 0.118% before the start of the peritectic reaction. The microstructure of 4Cr13 steel was martensite, retained austenite and primary carbide M7C3. Higher nitrogen content increased the content of retained austenite in martensitic stainless steel, inhibited the precipitation of primary carbides and refined the dendrites. Higher nitrogen content could effectively inhibit the microsegregation of C element in martensitic stainless steel; however, it had little effect on Cr, V, Nb and Ti. The peritectic reaction was first carried out in high nitrogen steel during solidification, which advanced the transformation of austenite and inhibited the microsegregation of C element.
  • Le-li Chen, Rui Luo, Pei Gao, Tian-wei Yin, Hui-xia Hao, Dong-hua Sheng, Tian Liu, Heng-nan Ding, Yu Cao, Bao-sen Zhang, Xiao-nong Cheng
    钢铁研究学报(英文版). 2023, 30(09): 1862-1872.
    https://doi.org/10.1007/s42243-022-00863-8
    摘要 ( )   可视化   收藏
    The hot deformation behavior of 316H stainless steel used in the 4th-generation nuclear systems was investigated by thermal compression tests at 1000–1150 C and 0.01–10 s-1. It was found that true stress firstly increased and then decreased with the increasing strain rate with a threshold of 1 s-1. Electron backscatter diffraction was used to analyze the microstructure evolution. Discontinuous dynamic recrystallization (DDRX) was the dominant dynamic recrystallization (DRX) mechanism, while continuous dynamic recrystallization (CDRX) was the supplementary one. DDRX happened before CDRX and provided additional nucleation sites for the latter. Twin grain boundaries (R3) appeared in DRX grains due to growth accidents. As the length fraction of R3 increased, the coincidence site lattice (CSL) boundary transition began to occur, forming R9 and R27. After the occurrence of full DRX, the growth and annexation of DRX grains were easy to be promoted, in which progress both equiaxed grains and CSL boundaries disappeared. The ideal deformation microstructure with fine and uniform DRX grains, which was accompanied by a high length fraction of CSL boundaries, appeared at 1000 °C–0.01 s-1, 1050 °C–0.01–0.1 s-1, 1100 °C–0.1–1 s-1 and 1150 °C–1–10 s-1. That is, the deformation conditions mentioned above were the preferable thermal forming parameters for 316H stainless steel in actual productions.
  • Ming Zhong, Da-ming Guo, Somnath Basu, Cong Wang
    钢铁研究学报(英文版). 2023, 30(09): 1873-1878.
    https://doi.org/10.1007/s42243-023-01017-0
    摘要 ( )   可视化   收藏
    Fused ternary CaF2–SiO2–MnO fluxes have been manufactured and applied to join EH36 shipbuilding steel under high heat input submerged arc welding. Five fluxes have been designed to clarify the effect of MnO content in CaF2–SiO2–MnO flux on the impact toughness of the weld metal, with the added amount of MnO from 10 to 50 wt.% at the expense of CaF2. With the increase in MnO content, the Charpy impact energy increases first and then decreases, experiencing a maximum value at 30 wt.% MnO. Microstructure of the weld metals has also been studied to account for impact toughness variations. It has been demonstrated that the highest acicular ferrite volume fraction in the weld metal is achieved at 30 wt.% MnO, which is concurrent to the maximum value of Charpy impact energy. It is believed that the Mn and O content variations in the weld metal contribute synergistically to such an interesting phenomenon.
  • Zheng-rong Ye, Jie Yang, Zheng-bin Wang, Xiang Zhou, Wei-dong Jiang, Ran Yi, Xiao-dong Cui, Zhi-hong Zhao
    钢铁研究学报(英文版). 2023, 30(09): 1879-1887.
    https://doi.org/10.1007/s42243-022-00853-w
    摘要 ( )   可视化   收藏
    The corrosion behavior of a carbon steel covered by sand deposits in the solution containing sulfate-reducing bacteria (SRB) under nitrogen purging conditions was studied by electrochemical measurements and surface analyses, aiming at clarifying the mitigation effects of nitrogen purging on SRB-involved under-deposit corrosion. The electrochemical results show that the variation trend of polarization resistance with immersion time is unchanged, but the corrosion current density is the lowest in the presence of SRB and deposits under nitrogen purging conditions, as compared to that without purging nitrogen, which are confirmed by the cross-sectional corrosion morphology observation after removing the sand deposits. Moreover, it is found that there are no positive synergistic effects between SRB and deposits on corrosion under nitrogen purging conditions, corresponding to the corrosion mitigation. Such mitigation on corrosion can be attributed to the less amount of SRB-produced H2S exhausted by purging nitrogen, which is supported by X-ray photoelectron spectrometry analyses. Therefore, purging nitrogen to the solution could be a practically effective way to mitigate the corrosion of deposit-covered carbon steels in SRB-containing solutions.
  • Xiao-wei Feng, Jia-xin Li, Zhi-bin Zheng, Bo Feng, Hao-kun Yang
    钢铁研究学报(英文版). 2023, 30(09): 1888-1895.
    https://doi.org/10.1007/s42243-023-00958-w
    摘要 ( )   可视化   收藏
    The feasibility of preparing Fe/Cu composite sheet was achieved by introducing submillimeter thickness Al sheet as an interlayer by rolling at room temperature. The shear test of the composite sheet supported that the metallurgical bonding strength between Fe/(Al)/Cu interface was stronger than that of Cu sheet at the initial state. With further 300 or 600 ºC annealing treatments, the interlayer subsequently exhibited brittle shear fracture, and the shear strength significantly dropped under the shear test. Furthermore, the tensile test pointed out that the tensile fracture mechanism changed from fracture as a whole structure to interlayer-to-layer delamination mode after annealing treatment. The microstructure and X-ray diffraction observations proved that the formation of Cu–Al intermetallic compounds (IMCs) along the interlayer resulted in brittle fracture, rather than that of Fe–Al IMCs after annealing, especially under 600 ºC annealing treatment. The investigation of the effect of the rolling process and annealing treatment on the mechanical properties of the Fe/(Al)/ Cu composite sheet shall provide instruction for high-quality composite metallic sheet fabrication.