150 mm×150 mm小方坯结晶器内流场及凝固行为模拟

贾进, 高飞, 罗霄, 邹铭, 周文浩, 张华, 方庆

连铸 ›› 2024, Vol. 43 ›› Issue (2) : 56-63.

PDF(4014 KB)
欢迎访问《连铸》官方网站!今天是 2025年7月29日 星期二
PDF(4014 KB)
连铸 ›› 2024, Vol. 43 ›› Issue (2) : 56-63. DOI: 10.13228/j.boyuan.issn1005-4006.20230091
专题研究

150 mm×150 mm小方坯结晶器内流场及凝固行为模拟

  • 贾进1, 高飞2, 罗霄1, 邹铭2, 周文浩1, 张华2, 方庆1,2
作者信息 +

Simulation on flow and initial solidification behavior in a 150 mm×150 mm billet mold

  • 贾进1, 高飞2, 罗霄1, 邹铭2, 周文浩1, 张华2, 方庆1,2
Author information +
文章历史 +

摘要

结晶器是整个连铸过程的核心环节,其内钢液流动、传热及初始凝固行为直接影响着铸坯质量,而拉速和过热度等工艺条件是影响结晶器冶金行为的关键参数。以某厂150 mm×150 mm小方坯结晶器为研究对象,建立耦合数学模型,分析过热度及拉速对结晶器内钢液流动与传热行为的影响。结果表明,当拉速由2.4 m/min增至3.0 m/min时,结晶器出口处铸坯角部温度与面部温度分别由960 K、1 050 K增至1 040 K、1 200 K;结晶器出口处坯壳厚度由11.21 mm降至8.71 mm,计算域出口处坯壳由16 mm降至14 mm;当过热度由15 K增至35 K时,铸坯表面和中心温度相应升高,幅度大致为5~10 K,结晶器出口坯壳厚度由10.45 mm降至9.01 mm,计算域出口处坯壳厚度由15 mm降至13 mm。研究结果可为冷镦钢小方坯连铸结晶器制定合理的工艺参数提供理论指导。

Abstract

As the core link of the whole continuous steel casting process, the flow, heat transfer and initial solidification behavior of molten steel in the continuous steel casting mold directly affect the quality of the billet, and the process conditions such as casting speed and superheat are the key parameters affecting the metallurgical behavior of the continuous steel casting mold. A 150 mm×150 mm continuous casting billet mold in a factory is taken as the research object, and a coupled mathematical model is established to analyze the influence of superheat and casting speed on the flow and heat transfer behavior of molten steel in the mold. The results showed that when the casting speed increases from 2.4 m/min to 3.0 m/min, the surface temperature and corner temperature are slightly enhanced by about 10 K, the center temperature is slightly increased by about 1 K, the shell thickness at mold outlet is decreased from 11.21 mm to 8.71 mm, and decreased from 16 mm to 14 mm at computational outlet. When the superheat increases from 15 K to 35 K, the surface and center temperatures of the slab increase by about 5-10 K, the shell thickness at the mold outlet decreases from 10.45 mm to 9.01 mm, and decreased from 15 mm to 13 mm at computational outlet. The research outcomes can provide theoretical guidance for the formulation of reasonable process parameters of cold heading steel billet continuous casting mold.

关键词

结晶器 / 流场 / 初始凝固 / 拉速 / 过热度

Key words

mold / flow flied / initial solidification / casting speed / superheat

图表

引用本文

导出引用
贾进, 高飞, 罗霄, . 150 mm×150 mm小方坯结晶器内流场及凝固行为模拟[J]. 连铸, 2024, 43(2): 56-63 https://doi.org/10.13228/j.boyuan.issn1005-4006.20230091
JIA Jin, GAO Fei, LUO Xiao, et al. Simulation on flow and initial solidification behavior in a 150 mm×150 mm billet mold[J]. Continuous Casting, 2024, 43(2): 56-63 https://doi.org/10.13228/j.boyuan.issn1005-4006.20230091

参考文献

[1] 孙江波, 刘旋, 翟晓毅, 等. 10B21冷镦钢线材表面翘皮缺陷成因分析[J]. 连铸, 2018(5): 39.
[2] LI Z, WU D, LÜ W. Effects of rolling and cooling conditions on microstructure and mechanical properties of low carbon cold heading steel[J]. Journal of Iron and Steel Research, International, 2012, 19(11): 64.
[3] 张先鸣.我国冷镦钢的现状和发展[J].金属制品,2009, 35(2): 43.
[4] 赵家七, 蔡小锋, 马建超, 等. 铝镇静冷镦钢CaS结瘤机理及改进[J]. 钢铁, 2021, 56(9): 80.
[5] 王利军,阮士朋,王宁涛,等. 高强度螺栓用非调质钢的研制与应用[J]. 钢铁, 2018, 53(11): 102.
[6] 王强, 朱航宇, 孙剑, 等. SWRCH45K冷镦钢非金属夹杂物生成及演变行为[J]. 中国冶金, 2020, 30(11): 41.
[7] 王时松,王伟,李永康,等.ML08Al冷墩钢连铸坯表面质量优化研究[J]. 炼钢, 2018,34(4):40
[8] 付达超,文光华,刘耀宗,等.10B21冷镦钢连铸小方坯表面异常振痕成因分析及控制[J]. 连铸, 2020(3): 33.
[9] FEI P, MIN Y, LIU C, et al. Effect of continuous casting speed on mold surface flow and the related near-surface distribution of non-metallic inclusions[J]. International Journal of Minerals, Metallurgy, and Materials, 2019, 26(2): 8.
[10] 陈斌, 李海波, 季晨曦, 等. 浇铸参数对结晶器液面波动影响及其工业应用[J]. 钢铁, 2022, 57(7): 86.
[11] 朱苗勇. 高拉速连铸过程传输行为特征及关键技术探析[J]. 钢铁, 2021, 56(7): 1.
[12] 李小明, 王阳, 朱佳雨, 等. 水口位置对小方坯结晶器内流场和凝固的影响[J]. 钢铁, 2024, 59(1): 75.
[13] 陈希青, 雷琳琳, 宋异, 等. 板坯连铸浸入式水口控流的物理和数值模拟[J]. 中国冶金, 2023, 33(12): 42.
[14] 高煜,单庆林,王振东,等.不同断面及拉速对结晶器液面波动的影响[J].河北冶金,2023(12):33.
[15] 李阳.连铸板坯结晶器内钢液流速的控制与应用[J].河北冶金,2023(3):6.
[16] 马占彪,赵华,王学兵,等.方坯结晶器电磁搅拌电磁场的数值模拟[J].河北冶金,2022(11):8.
[17] 薛瑞, 张燕超, 张彩军, 等. 160 mm×160 mm小方坯连铸结晶器内流场数值模拟[J].中国冶金, 2020, 30(1): 51.
[18] 李康康, 张彩军, 肖鹏程, 等. 高拉速薄板坯连铸结晶器钢渣界面波动分析[J]. 连铸, 2021(1): 9.
[19] 仇德金. 小方坯高拉速结晶器流场和温度场模拟研究[D]. 西安:西安建筑科技大学, 2021.
[20] LI X, ZHANG Z, LÜ M, et al. Numerical simulation of the fluid flow, heat transfer, and solidification in ultrahigh speed continuous casting billet mold[J]. Steel Research International, 2022, 93(6): 2100673.
[21] LI X, ZHANG Z, LÜ M, et al. Effect of mold electromagnetic stirring on metallurgical behavior in ultrahigh speed continuous casting billet mold[J]. Steel Research International, 2023, 94(6): 2200796.
[22] 张小伟, 白晓路, 石磊, 等. SWRH72B-S绞线钢连铸小方坯凝固温度场数值模拟[J]. 连铸, 2023(1):18.
[23] 张静, 马靓, 吴会平. 水口结构对连铸中低碳钢流场和温度场的影响[J]. 钢铁, 2019, 54(8): 116.
[24] YU S, LONG M, ZHANG M, et al. Effect of mold corner structures on the fluid flow, heat transfer and inclusion motion in slab continuous casting molds[J]. Journal of Manufacturing Processes, 2021, 68: 1784.
[25] 张然, 许琳, 韩泽峰, 等. 立式组合电磁制动对CSP结晶器内钢液流动及偏流控制[J]. 中国冶金, 2022, 32(1): 44.
[26] WANG J, FANG Q, HUANG L, et al. Three-phase flow in a single-strand tundish during start-up operation using top-swirling turbulence inhibitor[J]. Metallurgical and Materials Transactions B, 2023, 54(2): 635.
[27] 李少翔, 张晓萌, 李亮, 等. 连铸流动与凝固耦合模拟中糊状区系数的表征及影响[J]. 工程科学学报, 2019,41(2): 199.
[28] 方庆. 大方坯连铸过程流动, 传热, 传质行为及凝固组织的模拟研究[D]. 武汉:武汉科技大学, 2018.
[29] 方庆, 倪红卫, 王社教, 等. Q345E 钢 Φ600 mm 大圆坯连铸凝固数值模拟[J]. 炼钢, 2014, 30(5): 57.
[30] FANG Q, NI H, WANG B, et al. Effects of EMS induced flow on solidification and solute transport in bloom mold[J]. Metals, 2017, 7(3): 72.

基金

国家自然科学基金资助项目(52004191); 中国博士后科学基金资助项目(2022M711120);湖北省教育厅科学技术研究资助项目(B2022020)

PDF(4014 KB)

61

Accesses

0

Citation

Detail

段落导航
相关文章

/