|
|
Research progress on strengthening mechanism and ballistic performance of high nitrogen austenitic stainless steels |
WANG Yu1, PENG Xiang-fei1, LI Jun2, YANG Yang3, LI Guo-ping2, LIU Yan-lin3 |
1. School of Material Science and Engineering, North University of China, Taiyuan 030051, Shanxi, China; 2. State Key Laboratory of Advanced Stainless Steels, Taiyuan Iron and Steel Group Co., Ltd., Taiyuan 030003, Shanxi, China; 3. Ningbo Branch, China Academy of Ordnance Sciences, Ningbo 315103, Zhejiang, China |
|
|
Abstract High-nitrogen austenitic stainless steel (HNASS) is a novel material which is developing rapidly and used in transportation, marine engineering, building materials, medical equipment, military industry and other fields. Compared with traditional austenitic stainless steels, HNASS has excellent mechanical properties,such as good strength, toughness, high creep resistance and corrosion resistance. Nitrogen in HNASS has good effect on refining grain size, deformation, solution and precipitation strengthening, which reflects the multidirectional effects of nitrogen in steel, and has a significant effect on the strength improvement of austenitic stainless steel. Among the various strengthening effects, the solution strengthening of nitrogen produces a similar effect with the grain refining, that is, the plasticity of the material is not reduced when the nitrogen element is used to enhance the strength of the material. At the same time, in the aspect of dynamic mechanical properties, with the increasing of HNASS compression strain rate, the compressive strength increases first and then decrease, while the strain hardening index will increase. HNASS also has excellent impact energy absorption effect and hardening properties, especially the dynamic impact hardening properties, which obtained more plastic deformation through the plastic area. Therefore, HNASS has a broad application prospect in the field of anti-missile Armor protection. In order to systematically and comprehensively analyse the research status of nitrogen element on strengthening mechanism and dynamic protection performance of HNASS, the effect of nitrogen element in HNASS along with its dynamic mechanical properties and penetration plate target action were systematically reviewed in combination with the research status at home and abroad. The research prospects of HNASS in high efficiency nitrogen fixation process, effects of nitrogen content gradient and multi-component composite system were also proposed.
|
Received: 24 June 2021
|
|
|
|
[1] 马云超,房菲. 高氮奥氏体不锈钢中氮含量的预测及控制研究现状[J]. 锅炉制造,2016(2):49. (MA Yun-chao,FANG Fei. Study on predictive model and control mechanism of nitrogen content on high nitrogen austenitic stainless steels[J]. Boiler Manufacturing,2016(2):49.) [2] 石峰,崔文芳,王立军,等. 高氮奥氏体不锈钢研究进展[J]. 上海金属,2006,28(5):45. (SHI Feng,CUI Wen-fang,WANG Li-jun,et al. Advance in the research of high-nitrogen austenitic stainless steels[J]. Shanghai Metals,2006,28(5):45.) [3] 朱红春,姜周华,李花兵,等. 加压技术在高品质特殊钢冶炼和凝固中的作用[J]. 钢铁,2015,50(11):37. (ZHU Hong-chun,JIANG Zhou-hua,LI Hua-bing,et al. Effect of pressurization technology on steel-making and solidification of high-grade special steels[J]. Iron and Steel,2015,50(11):37.) [4] 张鹏,陈鹏飞. CRONIDUR30高氮不锈钢的热处理工艺及组织和性能[J]. 热处理,2020,35(1):1. (ZHANG Peng,CHEN Peng-fei. Heat treatment processes and resulting microstructure and hardness for a high-nitrogen stainless steel[J]. Heat Treatment,2020,35(1):1.) [5] 刘海定,王东哲,魏捍东,等. 高氮奥氏体不锈钢的研究进展[J]. 特殊钢,2009,30(4):45. (LIU Hai-ding,WANG Dong-zhe,WEI Han-dong,et al. Research progress in high nitrogen austenite stainless steel[J]. Special Steel,2009,30(4):45.) [6] 宁小智,邢长军,雍歧龙,等. 氮含量对高氮不锈钢硬化和软化特性的影响[J]. 钢铁,2021,56(3):66. (NING Xiao-zhi,XING Chang-jun,YONG Qi-long,et al. Effect of nitrogen contentration on hardening and softening properties of high nitrogen stainless steel[J]. Iron and Steel,2021,56(3):66.) [7] Jo M C,Kim S,Suh D W,et al. Effect of tempering conditions on adiabatic shear banding during dynamic compression and ballistic impact tests of ultra-high-strength armor steel[J]. Materials Science and Engineering:A,2020,792:139818. [8] 胡玲,李烈军,彭翰林,等. 粉末冶金多孔高氮奥氏体不锈钢的制备及性能[J]. 材料研究学报,2019,33(5):345. (HU Ling,LI Lie-jun,PENG Han-lin,et al. Fabrication and properties of powder metallurgical porous high nitrogen austenitic stainless steel[J]. Chinese Journal of Materials Research,2019,33(5):345.) [9] Adeoek F I. The effect of nitrogen on some chromium and some iron-chromium alloys[J]. Iron and Steel Institute,1926,114(1):117. [10] 彭霞锋. 高氮合金钢的动态压缩实验及动态本构关系[D]. 成都:西南交通大学,2009. (PENG Xia-feng. Dynamical Compression Experiment and Dynamical Constitutive Law of High Nitrogen Steel[D]. Chengdu:Southwest Jiaotong University,2009.) [11] 余蓉. 高氮不锈钢的开发进展[J]. 世界钢铁,2010,10(1):37. (YU Rong. Development progress of high nitrogen stainless steel[J]. World Iron and Steel,2010,10(1):37.) [12] Berns H. Manufacture and application of high nitrogen steels[J]. International Journal of Materials Research,1995,86(3):156. [13] 崔大伟,伦冠德,王金龙,等. 机械合金化及放电等离子烧结制备高氮奥氏体不锈钢[J]. 金属热处理,2018(10):13. (CUI Da-wei,LUN Guan-de,WANG Jin-long,et al. Preparation of high nitrogen austenitic stainless steel by mechanical alloying and spark plasma sintering[J]. Heat Treatment of Metals,2018(10):13.) [14] Rashev T V,Eliseev A V,Zhekova L T,et al. High-nitrogen steel[J]. Steel in Translation,2019,49(7):433. [15] 李建新,赵英利,王国营,等. 冷轧变形量对高氮奥氏体不锈钢Mn17Cr19 N0.6组织和性能的影响[J]. 特殊钢,2020,41(1):61. (LI Jian-xin,ZHAO Ying-li,WANG Guo-ying,et al. Effect of cold rolling deformation on structure and property of high nitrogen austenitic stainless steel Mn17Cr19N0.6[J]. Special Steel,2020,41(1):61.) [16] 陈蓉,时捷,董瀚,等. 含氮奥氏体钢与马氏体钢的抗弹行为研究[J]. 兵器材料科学与工程,2006(2):46. (CHEN Rong,SHI Jie,DONG Han,et al. Ballistic behavior of nitrogen alloyed and martensitic steel plates[J]. Ordnance Material Science and Engineering,2006(2):46.) [17] 史学红,李彦鑫,侯向东,等. 载荷对高氮不锈钢和304不锈钢磨损行为的影响[J]. 中国冶金,2020,30(10):49. (SHI Xue-hong,LI Yan-xin,HOU Xiang-dong,et al. Effect of load on wear behaviors of high nitrogen stainless steel and 304 stainless steel[J]. China Metallurgy,2020,30(10):49.) [18] 武海玲,苗成,白利红,等. 685装甲钢动态拉伸与压缩性能研究[J]. 兵器装备工程学报,2019(7):18. (WU Hai-ling,MIAO Cheng,BAI Li-hong,et al. Study on dynamic tensile and compressive properties of 685 armored steel[J]. Journal of Ordnance Equipment Engineering,2019(7):18.) [19] Singh B B,Sukumar G,Paman A,et al. A comparative study on the ballistic performance and failure mechanisms of high-nitrogen steel and rha steel against tungsten heavy alloy penetrators[J]. Journal of Dynamic Behavior of Materials,2021,7(1):60. [20] 翁德伟. 坦克装甲车辆防护材料的研究现状及发展趋势[J]. 冶金与材料,2019(4):33. (WENG De-wei. Research status and development trend of protective materials for tank armoured vehicles[J]. Metallurgy and Materials,2019(4):33.) [21] 曹阳,姜周华,李花兵,等. 高氮不锈钢粉末冶金制备技术的研究进展[J]. 中国冶金,2007,17(10):4. (CAO Yang,JIANG Zhou-hua,LI Hua-bing,et al. Development in technology for producing high nitrogen stainless steels by power metallurgy[J]. China Metallurgy,2007,17(10):4.) [22] Jo M C,Kim S,Kim D W,et al. Understanding of adiabatic shear band evolution during high-strain-rate deformation in high-strength armor steel[J]. Journal of Alloys and Compounds,2020,845:155540. [23] 陈巍,刘燕林,齐志望,等. 高氮奥氏体装甲钢抗弹性能研究[J]. 兵器材料科学与工程,2009,32(6):51. (CHEN Wei,LIU Yan-lin,QI Zhi-wang,et al. Research on ballistic behavior of high nitrogen austenitic armor steel[J]. Ordnance Material Science and Engineering,2009,32(6):51.) [24] 姜周华. 高氮不锈钢开发和应用的最新进展[C]//第十届中国钢铁年会暨第六届宝钢学术年会论文集II. 上海:中国金属学会,宝钢集团有限公司,2015:1487. (JIANG Zhou-hua. Latest progress in the development and application of high nitrogen stainless steel[C]//Proceedings of the Tenth China Iron and Steel Annual Meeting and the Sixth Baosteel Academic Annual Meeting II. Shanghai:The Chinese Society for Metals,Baosteel Group Co.,Ltd.,2015:1487.) [25] 曹阳,朱世范,果春焕,等. 新型金属间化合物基层状装甲防护复合材料[J]. 兵器材料科学与工程,2014,37(6):122. (CAO Yang,ZHU Shi-fan,GUO Chun-huan,et al. Novel metal-intermetallic laminate composite for armor material[J]. Ordnance Material Science and Engineering,2014,37(6):122.) [26] 王鼎,王伟,赵英利,等. 固溶处理对高氮奥氏体不锈钢组织和力学性能的影响[J]. 兵器材料科学与工程,2019,42(1):98. (WANG Ding,WANG Wei,ZHAO Ying-li,et al. Effect of solution treatment on microstructure and mechanical properties of high nitrogen austenitic stainless steel[J]. Ordnance Material Science and Engineering,2019,42(1):98.) [27] 常金宝,赵英利,嵇爽,等. 固溶时效对节镍型高氮奥氏体不锈钢组织的影响[J]. 金属热处理,2020,45(2):120. (CHANG Jin-bao,ZHAO Ying-li,JI Shuang,et al. Effect of solution treatment and aging on microstructure of low-nickel high nitrogen austenitic stainless steel[J]. Heat Treatment of Metals,2020,45(2):120.) [28] Speidel M O,Kowanda C,Diener M. High Nitrogen Steel 2003[M]. Swiss:Institute of Metallurgy,2003. [29] 王松涛. 高氮奥氏体不锈钢的力学行为及氮的作用机理[D]. 北京:中国科学院研究生院(理化技术研究所),2008. (WANG Song-tao. Mechanical Behaviors and Mechanisms of Nitrogen Effect of High Nitrogen Austenitic Stainless Steels[D]. Beijing:Graduate School of Chinese Academy of Sciences(Technical Institute of Physics and Chemistry),2008.) [30] Zhou R,Northwood D O,Liu C. On nitrogen diffusion during solution treatment in a high nitrogen austenitic stainless steel[J]. Journal of Materials Research and Technology,2020,9(2):2331. [31] Hu L,Peng H,Baker I,et al. Characterization of high-strength highnitrogen austenitic stainless steel synthesized from nitrided powders by spark plasma sintering[J]. Materials Characterization,2019,152:76. [32] 翁建寅,董瀚,李北,等. N含量对高氮CrMnMo奥氏体不锈钢组织和性能的影响[J]. 金属热处理,2020,45(1):160. (WENG Jian-yin,DONG Han,LI Bei,et al. Effect of nitrogen content on microstructure and properties of high nitrogen CrMnMo austenitic stainless steel[J]. Heat Treatment of Metals,2020,45(1):160.) [33] Simmons J W. Overview:High-nitrogen alloying of stainless steels[J]. Materials Science and Amp:Engineering A,1996,207(2):159. [34] 徐海峰,曹文全,俞峰,等. 国内外高氮马氏体不锈轴承钢研究现状与发展[J]. 钢铁,2017,52(1):53. (XU Hai-feng,CAO Wen-quan,YU Feng,et al. Current research status and development of domestic and foreign high nitrogen martensitic stainless bearing steel[J]. Iron and Steel,2017,52(1):53.) [35] Kumar C S,Chattopadhyay K,Singh V,et al. Enhancement of low-cycle fatigue life of high-nitrogen austenitic stainless steel at low strain amplitude through ultrasonic shot peening[J]. Materials Today Communications,2020,25:101576. [36] 李晓源,时捷,孙挺. 终轧温度对高氮奥氏体钢组织和力学性能的影响[J]. 中国冶金,2020,30(5):29. (LI Xiao-yuan,SHI Jie,SUN Ting. Effects of finish rolling temperature on microstructure and mechanical properties of high nitrogen austenitic steel[J]. China Metallurgy,2020,30(5):29.) [37] Lach E,Koerber G,Scharf M,et al. Comparison of nitrogen alloyed austenitic steels and high strength armor steels impacted at high velocity[J]. International Journal of Impact Engineering,1999,23(1):509. [38] Ikegami Y,Nemoto R. Effect of thermo-mechanical treatment on mechanical properties of high-nitrogen containing Cr-Mn-Ni austenitic stainless steels[J]. ISIJ International,1996,36(7):855. [39] 王正国. 高氮奥氏体不锈钢显微组织及力学性能的研究[D]. 太原:太原理工大学,2011. (WANG Zheng-guo. Study on the Microstructure and Mechanical Property in High Nitrogen Austenitic Stainless Steel[D]. Taiyuan:Taiyuan University of Technology,2011.) [40] 胡庚祥,蔡珣,戎咏华. 材料科学基础[M]. 上海:上海交通大学出版社,2010. (HU Geng-xiang,CAI Xun,RONG Yong-hua. Fundamentals of Materials Science[M]. Shanghai:Shanghai Jiaotong University Press,2010.) [41] 宁小智,邢长军,雍岐龙,等. 热拔工艺对高氮无镍奥氏体不锈钢线材开裂的影响[J]. 中国冶金,2020,30(5):47. (NING Xiao-zhi,XING Chang-jun,YONG Qi-long,et al. Influence of hot drawing process on cracking of high nitrogen nickel free austenitic stainless steel wire rod[J]. China Metallurgy,2020,30(5):47.) [42] Kim S J,Lee T H,Oh C S. Effect of nitrogen on the deformation behaviour of high-nitrogen austenitic stainless steels[J]. Steel Research International,2009,80(7):467. [43] Masumura T,Seto Y,Tsuchiyama T,et al. Work-hardening mechanism in high-nitrogen austenitic stainless steel[J]. Materials Transactions,2020,61(4):678. [44] 徐明舟. 高氮奥氏体不锈钢的力学行为和组织稳定性[D]. 沈阳:东北大学,2011. (XU Ming-zhou. Mechanical Behaviors and Microstructural Stability of High Nitrogen Austenitic Stainless Steel[D]. Shenyang:Northeast University,2011.) [45] 徐国富. 高氮奥氏体不锈钢组织调控和力学性能的研究[D]. 武汉:华中科技大学,2013. (XU Guo-fu. Study on the Regulation of Microstructure and Mechanical Properties of High Nitrogen Austenitic Stainless Steel[D]. Wuhan:Huazhong University of Science and Technology,2013.) [46] Singh B B,Sukumar G,Rao P P,et al. Superior ballistic performance of high-nitrogen steels against deformable and non-deformable projectiles[J]. Materials Science and Engineering:A,2019,751:115. [47] 束德林. 工程材料力学性能[M]. 北京:机械工业出版社,2011. (SHU De-lin. Mechanical Properties of Engineering Materials[M]. Beijing:Mechanical Industry Press,2011.) [48] 房菲,李静媛,王一德. 18Mn18Cr高氮钢析出相特征及形成机制[J]. 北京科技大学学报,2014,36(6):768. (FANG Fei,LI Jing-yuan,WANG Yi-de. Characteristics and forming mechanism of precipitates in 18Mn18Cr high nitrogen steel[J]. Journal of University of Science and Technology Beijing,2014,36(6):768.) [49] 陈雨来,房菲,李静媛,等. C含量对高氮奥氏体不锈钢18Mn18CrN析出行为的影响[J]. 材料热处理学报,2015,36(9):94. (CHEN Yu-lai,FANG Fei,LI Jing-yuan,et al. Effect of C content on precipitation behavior of high-nitrogen austenitic stainless steel 18Mn18CrN[J]. Transactions of Materials and Heat Treatment,2015,36(9):94.) [50] SHI F,HU J,WANG L F,et al. Inhibition of nitride precipitation in a Fe-Cr-Mn-Mo-N high-nitrogen austenitic stainless steel through grain boundary character distribution optimization[J]. Journal of Physics:Conference Series,2021,1906(1):012016. [51] 赵兰英,陈家兴. 时效处理对Cr20Mn18N0.5高氮奥氏体不锈钢组织与力学性能的影响[J]. 热加工工艺,2020,49(22):132. (ZHAO Lan-ying,CHEN Jia-xing. Effects of aging treatment on microstructure and mechanical properties of Cr20Mn18N0.5 high nitrogen austenitic stainless steel[J]. Hot Working Technology,2020,49(22):132.) [52] 宁小智,邢长军,雍歧龙,等. 氮含量对无镍奥氏体不锈钢理化性能的影响[J]. 中国冶金,2019,29(6):34. (NING Xiao-zhi,XING Chang-jun,YONG Qi-long,et al. Effects of nitrogen content on physical and chemical properties of nickel-free austenitic stainless steels[J]. China Metallurgy,2019,29(6):34.) [53] 张泽宁,杨吉春,富晓阳,等. 高氮低镍奥氏体不锈钢的力学性能及析出相[J]. 金属热处理,2019(8):15. (ZHANG Ze-ning,YANG Ji-chun,FU Xiao-yang,et al. Mechanical properties and precipitates of high nitrogen and low nickel austenitic stainless steel[J]. Heat Treatment of Metals,2019(8):15.) [54] 徐效谦. 不锈钢中的沉淀硬化相[C]//第24届年会暨2016金属制品行业技术信息交流会论文集. 常州:中国金属学会,全国金属制品信息网,2016:51. (XU Xiao-qian. Precipitation hardening phase in stainless steel[C]//Proceedings of the 24th Annual Meeting and 2016 Technical Information Exchange Meeting of Metal Products Industry. Changzhou:The Chinese Society for Metals,National Metal Products Information Network,2016:51.) [55] 房菲,黄健,李静媛. 氮含量对18Mn18CrN钢高温性能的影响[J]. 上海金属,2017,39(1):38. (FANG Fei,HUANG Jian,LI Jing-yuan. Influence of nitrogen content on high temperature properties of 18Mn18CrN steel[J]. Shanghai Metals,2017,39(1):38.) [56] HONG C M,SHI J,SHENG L,et al. Influence of hot working on microstructure and mechanical behavior of high nitrogen stainless steel[J]. Journal of Materials Science,2011,46(15):5097. [57] Ogawa M,Hiraoka K,Katada Y,et al. Chromium nitride precipitation behavior in weld heat-affected zone of high nitrogen stainless steel[J]. ISIJ International,2002,42(12):1391. [58] MIAO C,ZHONG T,WU H,et al. Study on dynamic mechanical properties of high nitrogen steels[J]. Defence Technology,2018,14(5):496. [59] Fréchard S,Redjaïmia A,Lach E,et al. Dynamical behaviour and microstructural evolution of a nitrogen-alloyed austenitic stainless steel[J]. Materials Science and Engineering:A,2008,480(1/2):89. [60] 李花兵. 高氮奥氏体不锈钢的冶炼理论基础及其材料性能研究[D]. 沈阳:东北大学,2008. (LI Hua-bing. Metallurgical Fundamental and Properties of High Nitrogen Austenitic Stainless Steels[D]. Shenyang:Northeast University,2008.) [61] 曹呈祥,崔怀周,梁强,等. Mn18Cr18N高氮奥氏体不锈钢的冶炼工艺[J]. 中国冶金,2021,31(5):98. (CAO Cheng-xiang,CUI Huai-zhou,LIANG Qiang,et al. Smelting process of Mn18Cr18N high nitrogen austenitic stainless steel[J]. China Metallurgy,2021,31(5):98.) [62] 陈小安,邵冰莓,宋顺成,等. 高氮合金钢高应变率剪切性能测试[J]. 浙江大学学报(工学版),2011,45(11):1948. (CHEN Xiao-an,SHAO Bing-mei,SONG Shun-cheng,et al. Measurements of shearing property of high N alloy steel at super high strain rates[J]. Journal of Zhejiang University(Engineering Edition),2011,45(11):1948.) [63] Singh B B,Sukumar G,Sivakumar K,et al. A comparative study on the ballistic performance of high nitrogen steel and rolled homogeneous armour steel against 7.62 mm ball and 12.7 mm armour piercing projectiles[J]. Materials Today:Proceedings,2021,41:1188. [64] ZHANG F C,FU R,QIU L,et al. Microstructure and property of nitrogen-alloyed high manganese austenitic steel under high strain rate tension[J]. Materials Science and Engineering:A,2008,492(1/2):255. |
[1] |
YANG Yi1,2, ZHENG Zhibin2, YE Zhiguo1, YANG Haokun3, LONG Jun2, ZHENG Kaihong2. Microstructure and mechanical properties of light weight high manganese steel[J]. JOURNAL OF IRON AND STEEL RESEARCH , 2021, 33(11): 1189-1197. |
[2] |
LIU Si-han, WANG Cun-yu, XU Hai-feng, CAO Wen-quan. Superplasticity and microstructure evaluation of cold rolled medium manganese steels[J]. Iron and Steel, 2020, 55(9): 97-103. |
[3] |
HAN Yan-jie, ZHANG Qi-feng, QIAN Hui, CAO Yin-ping, YANG Jun-he, YANG Guang-zhi. Relationship between Raman structure andreactivity of coke matrix[J]. Iron and Steel, 2020, 55(8): 81-85. |
[4] |
LI Xiao-yuan,SHI Jie. Ballistic behavior of high strength steel targets during high speed impact of projectile[J]. JOURNAL OF IRON AND STEEL RESEARCH , 2020, 32(5): 429-436. |
[5] |
YANG Geng-wei,LU Jia-wei,SUN Hui,FANG Zi-wei,ZHOU Yi-liao,YAO Nan. Microstructure, mechanical properties and phase transformation behavior of TiV microalloyed highstrength hotstrip steel[J]. JOURNAL OF IRON AND STEEL RESEARCH , 2019, 31(8): 726-732. |
[6] |
WU Keng,SHE Yuan,,LIU Qi-hang,ZHAN Wen-long. Consideration on properties of coke and coke deterioration after large-scale blast furnace[J]. Iron and Steel, 2017, 52(10): 1-12. |
|
|
|
|