热镀锌机组圆盘剪工艺参数优化技术的开发

doi:10.13228/j.boyuan.issn0449-749x.20210364

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (1342 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract In order to study the main cutting edge quality problems such as the disc shear equipment failure due to improper setting of the cutting process parameters and the occurrence of burrs, burrs and unbalanced cut-off ratio at the edge of the strip due to improper setting of the cutting process parameters during the work. This article takes the disc shear equipment of a hot-dip galvanizing line of a steel plant as the research object, and conducts research on the equipment itself and process parameters. Through the analysis of the factors that affect the quality of the strip edges and the correlation of the input variables of the BP neural network, the four factors of the front tension, the amount of clearance, the amount of overlap, and the amount of trimming are selected as variables and the hot-rolled strip steel disc is analyzed. Based on the shearing mechanism of the blades, combined with the technological characteristics of the disc shearing equipment and the relevant parameters in the cutting process, with the goal of preventing equipment failures and improving the quality of the current edge, the different indicators of the strip edge are carried out correspondingly quantify, put forward the strip quality evaluation function, and use the calculation result as the output layer of BP neural network. On this basis, a model based on PSO-BP neural network was established, and a set of hot-dip galvanizing line trimming process optimization technology was developed. The data source, processing method and the setting method of the parameters of the PSO-BP neural network are also given. The technology trains the BP neural network based on the tens of thousands of key production process parameters of disc shears collected on site, and fits the nonlinear function on this basis. Finally, the particle swarm algorithm PSO is used to analyze the better disc shear clearance. Process parameters such as the amount of overlap and the front and rear tension have caused the trimming quality problem at the edge of the strip after the disc shears. The ratio of the total trimming kilometers is significantly lower than before, which effectively improves the trimming quality of the strip. Lays a foundation for the improvement of unit production efficiency, and at the same time creates better economic benefits for the enterprise.

Key words： hot-dip galvanizing disc cutter trimming quality neural network particle swarm algorithm

Received: 21 June 2021

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	BAI Zhen-hua
	LIN Wei
	WANG Wei
	ZHANG Wen-jun
	LI Xue-tong

Cite this article:

BAI Zhen-hua,LIN Wei,WANG Wei等. Development of optimization technology for disc shear process parameters of hot-dip galvanizing line[J]. Iron and Steel, 2022, 57(1): 159-166.

URL:

http://www.chinamet.cn/Jweb_gt/EN/10.13228/j.boyuan.issn0449-749x.20210364 OR http://www.chinamet.cn/Jweb_gt/EN/Y2022/V57/I1/159

[1] 刘宏民,于丙强,杨利坡,等. 整辊镶块智能型冷轧带钢板形仪的研制与工业应用[J]. 钢铁,2011,46(12):86.(LIU Hong-min,YU Bing-qiang,YANG Li-po,et al. Development and industrial application of an intelligent cold-rolled strip shape meter with whole roll inserts[J]. Iron and Steel,2011,46(12):86.)
[2] 贾银芳,金尧成,马见华,等. 基于热轧原料数据的圆盘剪堵边预控系统[J]. 轧钢,2020,37(6):77.(JIA Yin-fang,JIN Yao-cheng,MA Jian-hua,et al. Disc shear caulking pre-control system based on hot-rolled raw material data[J]. Steel Rolling,2020,37(6):77.)
[3] 刘志恒,张乃强,李山,等. 高强钢切边剪工艺参数的优化[J]. 轧钢,2019,36(6):99.(LIU Zhi-heng,ZHANG Nai-qiang,LI Shan,et al. Optimization of process parameters of high-strength steel trimming shears[J]. Steel Rolling,2019,36(6):99.)
[4] YANG Li-po,YU Bing-qiang. Industrial shape detecting system of cold rolling strip[J]. Journal of Central South University,2012,19(4):994.
[5] YANG Li-po,YU Bing-qiang,YU Hua-xin. Online shape dynamic wrapping angle compensation model of cold strip[J]. Journal of Iron and Steel Research,International,2011,18(7):28.
[6] 岳宜科,唐国栋,王庆刚,等. 1 580酸洗机组圆盘剪切边质量控制研究[J]. 山东工业技术,2015(15):14.(YUE Yi-ke,TANG Guo-dong,WANG Qing-gang,et al. Research on quality control of disc shearing edge of 1 580 pickling line[J]. Shandong Industrial Technology,2015(15):14.)
[7] 白振华,钱承,刘亚星,等. 圆盘剪切边过程间隙量与重叠量综合优化技术[J]. 钢铁,2017,52(2):59.(BAI Zhen-hua,QIAN Cheng,LIU Ya-xing,et al. Comprehensive optimization technology of clearance and overlap in the process of disc shearing edge[J].Iron and Steel,2017,52(2):59.)
[8] 张林斌. 提高热轧圆盘剪剪切质量的方法[J]. 设备管理与维修,2018(18):69.(ZHANG Lin-bin. Methods to improve the shear quality of hot-rolled disc shears[J]. Equipment Management and Maintenance,2018(18):69.)
[9] 胡建军,周保欣,刘顺明. 圆盘剪剪切原理及切边质量控制[J]. 重型机械,2012(6):58.(HU Jian-jun,ZHOU Bao-xin,LIU Shun-ming. The principle of disc shear and the quality control of trimming[J]. Heavy Machinery,2012(6):58.)
[10] 王康健,郑涛. 被动式圆盘剪工艺参数优化设定技术的研究与应用[J]. 机械工程与自动化,2015(4):137.(WANG Kang-jian,ZHENG Tao. Research and application of technology parameter optimization setting of passive disc shears[J]. Mechanical Engineering and Automation,2015(4):137.)
[11] 徐善敏. 宝钢5 m宽厚板轧机剪切线设备与剪切质量的相关因素[J]. 宝钢技术,2005(2):34.(XU Shan-min. Factors related to the shear line equipment and shear quality of Baosteel′s 5 m wide and heavy plate mill[J]. Baosteel Technology,2005(2):34.)
[12] 谢浩. 基于BP神经网络及其优化算法的汽车车速预测[D]. 重庆:重庆大学,2014.(XIE Hao. Automobile Speed Prediction Based on BP Neural Network and its Optimization Algorithm[D]. Chongqing:Chongqing University,2014.)
[13] 王东风,孟丽,赵文杰. 基于自适应搜索中心的骨干粒子群算法[J]. 计算机学报,2016,39(12):2652.(WANG Dong-feng,MENG Li,ZHAO Wen-jie. Backbone particle swarm optimization algorithm based on adaptive search center[J]. Chinese Journal of Computers,2016,39(12):2652.)
[14] Bergh F van den, Engelbrecht A P. A study of particle swarm optimization particle trajectories[J]. Information Sciences,2005,176(8):937.