基于脉冲燃烧控制的退火炉热负荷分配模型

doi:10.13228/j.boyuan.issn0449-749x.20210270

Abstract
Figure/Table
References
Related Citation (9)

Download: PDF (3945 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract The on-off controlled combustion technology is widely used in various heating furnaces because of its good dynamic response, high temperature control accuracy, low gas consumption and pollutant discharge level. For vertical annealing furnace, there are three common heating models: the proportional model, the narrow model, the normal model. In line running status, operators can choose corresponding models according to the risks of strip deviation and buckling in the radiant tube heating section,but none of these three models are unable to avoid the problems of sudden cooling and heating of the radiator tube due to frequent opening and closing of burners. It could further induce the deformation and cracking of radiation tubes,abnormal consumption of ignition electrodes and control valves and large fluctuation of gas pressure. In order to reduce the frequency of burner opening and closing times,a "stair-climbing" type heating output distribution model was established. The relationship between the controller output of strip temperature and the heating output of each column at radiant tube heating section was fitted,and the correction function of heating output distribution model for the radiant tube heating section was obtained via the interpolation. It met the requirement that the calculated values of the model was consistent with the actual values. The upper and lower limits of each column of heating output were adjusted so that the heating output was distributed in a "stair climbing" manner. The function that the burners in the inlet area of the low power heating section do not work and the burners in the outlet area always work was realized in vertical annealing furnace. A completed combustion cycle was tested. It showed that the "stair climbing" model can greatly reduce the frequency of burner opening and closing times, under a complete combustion cycle. At the condition of 89.6% strip temperature controller output at the radiant tube heating section,the burner was switched on and off for 324 times,whereas it was only 32 times for the "stair-climbing" distribution model. When the strip temperature controller output of the radiant tube heating section is 89.6%, the switching frequency of the burner under the control of the traditional model is 324 times, while that of the "stair climbing" distribution model is only 32 times.

Key words： vertical annealing furnace radiant tube heating section (RTF) burner on-off control heating output "stair-climbing"distribution model

Received: 08 May 2021

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	REN Wei-chao
	ZHU Guo-ming
	LI Yang-long
	LI Guan-xiong
	ZHOU Huan
	WANG Dao-jin

Cite this article:

REN Wei-chao,ZHU Guo-ming,LI Yang-long等. Distribution model of heating output based on on-off controlled annealing furnace[J]. Iron and Steel, 2022, 57(1): 151-158.

URL:

http://www.chinamet.cn/Jweb_gt/EN/10.13228/j.boyuan.issn0449-749x.20210270 OR http://www.chinamet.cn/Jweb_gt/EN/Y2022/V57/I1/151

[1] 胡韬. 冷轧连续退火炉温度控制系统研究[D]. 沈阳:东北大学,2013.(HU Tao. Research on Temperature Control System of Cold Rolling Continuous Annealing Furnace[D]. Shenyang:Northeastern University,2013.)
[2] 郭琪,李元华,刘文鹏,等. 连退炉辐射管时序脉冲燃烧控制方式的应用和分析[J]. 电工钢,2020,2(2):45.(GUO Qi,LI Yuan-hua,LIU Wen-peng,et al. Application and analysis of timing pulse combustion control mode in continuous furnace radiant tube[J]. Electrical Steel,2020,2(2):45.)
[3] 赵义琴,温治.脉冲蓄热式燃烧技术在台车退火炉上的应用[J]. 冶金能源,2014,33(4):35.(ZHAO Yi-qin,WEN Zhi. Application of pulse HTAC combustion technology in trolley annealing furnace[J]. Energy for Metallurgical Industry,2014,33(4):35.)
[4] 张云明. 脉冲燃烧在板坯加热炉上的应用[J]. 冶金能源,2007,26(4):61.(ZHANG Yun-ming. Application of pulse burning in slab reheating furnace[J]. Energy for Metallurgical Industry,2007,26(4):61.)
[5] 陈焕德,张宇,周云,等. 蓄热式轧钢加热炉燃烧质量优化控制研究[J]. 冶金能源,2021,40(1):39.(CHEN Huan-de,ZHANG Yu,ZHOU Yun,et al. Study on combustion quality optimization control of regenerative reheating furnace for steel rolling[J]. Energy for Metallurgical Industry,2021,40(1):39.)
[6] 孙守钰,阎增范,刘浩,等. 加热炉智能燃烧控制技术分析与应用[J]. 冶金能源,2020,39(5):30.(SUN Shou-yu,YAN Zeng-fan,LIU hao,et al. Analysis and application of intelligent combustion control technology in heating furnace[J]. Energy for Metallurgical Industry,2020,39(5):30.)
[7] 蔡九菊. 钢铁工业的空气消耗与废气排放[J]. 钢铁,2019,54(4):1.(CAI Jiu-ju. Air consumption and waste gas emission of steel industry[J]. Iron and Steel,2019,54(4):1.)
[8] 高月,陈丽娟,赵帅,等. 加热炉自动燃烧系统的研究与应用[J]. 中国冶金,2021,31(1):46.(GAO Yue,CHEN Li-juan,ZHAO Shuai,et al. Research and application of automatic combustion system for heating furnace[J]. China Metallurgy,2021,31(1):46.)
[9] Strommer S,Niederer M,Steinboeck A,et al. Hierarchical nonlinear optimization-based controller of a continuous strip annealing furnace[J]. Control Engineering Practice,2018,73:40
[10] 郭琪. 鞍钢AA2机组连续退火炉燃烧控制系统优化[D]. 哈尔滨:哈尔滨工业大学,2016.(GUO Qi. Optimization of Combustion Control System Continuous Annealing Furnace of Ansteel′s AA2 Unit[D]. Harbin:Harbin Institute of Technology,2016.)
[11] 刘顺明,李洋龙,侯大伟,等. 连续退火炉W型辐射管破损调研及优化措施[J]. 钢铁,2018,53(6):103.(LIU Shun-ming,LI Yang-long,HOU Da-wei,et al. Damage investigation and optimization measures of W-shaped radiant tube in continuous annealing furnace[J]. Iron and Steel,2018,53(6):103.)
[12] 李昀泽. 包钢新体系冷轧连续退火炉温度监控系统的设计[D]. 内蒙古:内蒙古科技大学,2019.(LI Yun-ze. Design of Temperature Control System of Continuous Annealing Furnace for BISG[D]. Inner Mongolia:Inner Mongolia University of Science and Technology,2019.)
[13] 李元军,王鲁,黄继波,等. 某连续退火炉辐射管开裂原因[J]. 机械工程材料,2021,45(1):113.(LI Yuan-jun,WANG Lu,HUANG Ji-bo,et al. Cracking cause of radiant tube in a continuous annealing furnace[J]. Materials for Mechanical Engineering,2021,45(1):113.)
[14] 李军,李源,杨麒冰,等. 连续退火炉炉辊结瘤类缺陷原因分析及控制措施[C]//第十二届中国钢铁年会论文集. 北京:中国金属学会,2019:168.(LI Jun,LI Yuan,YANG Qi-bing,et al. Cause analysis and control measures of nodulation defects in rollers of continuous annealing furnace[C]//Proceedings of the 12^th CSM Steel Congress. Beijing:The Chinese Society for Metal,2019:168.)
[15] 郭健名. 连续退火炉加热控制技术的研究与改造[D]. 沈阳:东北大学,2012.(GUO Jian-ming. The Research and Improving on Heating Control Technology of CAL[D]. Shenyang:Northeastern University,2012.)
[16] 王鲁. 数字化脉冲燃烧控制技术在冷轧带钢连续退火炉上的应用[J]. 宝钢技术,2010(1):76.(WANG Lu. Application of the digital pulse combustion control system in the cold strip annealing furnace[J]. Baosteel Technology,2010(1):76.)
[17] 申凯,张文平. 一种连续退火炉脉冲燃烧燃气压力控制方法[J]. 冶金自动化,2017,41(4):48.(SHEN Kai,ZHANG Wen-ping. A method of pulse combustion system gas pressure control for continuous annealing furnace[J]. Metallurgical Industry Automation,2017,41(4):48.)
[18] 王瑞,白振华,王云祥,等. 连退过程带钢热瓢曲指数及其影响因素[J]. 钢铁,2016,51(12):94.(WANG Rui,BAI Zhen-hua,WANG Yun-xiang,et al. Damage investigation and optimization measures of W-shaped radiant tube in continuous annealing furnace[J]. Iron and Steel,2016,51(12):94.)