喷嘴射流特征对连铸二冷区蒸汽膜穿透行为的影响

doi:10.13228/j.boyuan.issn0449-749x.20220181

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (3481 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract The surface temperature of the slab in the second cooling zone of continuous casting is usually higher than 900 ℃. At this temperature,the spraying droplets will not wet the surface of the slab when they contact the high-temperature slab,but only form a vapor film on it,which prevents the subsequent heat transfer between the droplets and the slab surface. In view of the above problems,a nozzle jet simulation calculation model is established based on the flat water nozzle in the secondary cooling zone of continuous casting in a domestic steel plant. The model is verified by theoretical calculation and laboratory experiments. The flow field distribution in the free jet area of the nozzle is studied by numerical simulation and the evolution law of the jet droplet size is measured by the continuous casting nozzle cooling detection system. Combined with the numerical simulation results and laboratory measurement results,the variation law of the depth of the vapor film on the surface of the billet by the jet droplets impacted by the nozzle under different working conditions is quantitatively analyzed. The results show that the maximum jet velocity of the nozzle is at the nozzle outlet. The jet can maintain a large jet velocity near the nozzle outlet. With the increase of water volume,the distance of the jet to maintain a high jet velocity also increases. The axial velocity of the whole jet accounts for more than 80%. When the amount of water is larger, the particle size of jet droplets becomes smaller. As the distance from the nozzle outlet increases,the droplet size at the center of the jet increases gradually and reaches the maximum value. When the water flow rate is 9 and 12 L/min,respectively,the droplet size is basically the same,indicating that the increase of the cooling water does not affect the droplet size distribution when the water flow rate increases to a certain amount. Under different initial flow rates,the depth of droplet penetration through the steam film on the billet surface increases firstly and then decreases slightly with the increase of spray distance. When the spray distance is between 100-200 mm,the penetration depth of droplet is the largest,which indicates that the spray cooling effect is the best when the nozzle spray height is within this range.

Key words： secondary cooling nozzle velocity characteristics atomized droplet size film boiling heat transfer numerical simulation characteristic testing of nozzle

Received: 18 March 2022

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	MA Fan
	LIU Qing
	ZHANG Jiang-shan
	WANG Chao
	SUN Jian-kun
	LI Ming

Cite this article:

MA Fan,LIU Qing,ZHANG Jiang-shan等. Influence of jet characteristics nozzle on penetration behavior to vapor film in secondary cooling zones of continuous casting[J]. Iron and Steel, 2022, 57(10): 101-109.

URL:

http://www.chinamet.cn/Jweb_gt/EN/10.13228/j.boyuan.issn0449-749x.20220181 OR http://www.chinamet.cn/Jweb_gt/EN/Y2022/V57/I10/101

[1] 王新华. 钢铁冶金-炼钢学[M]. 北京:高等教育出版社,2007.(WANG Xin-hua. Iron and Steel Metallurgy-Steelmaking[M]. Beijing:Higher Education Press,2007.)
[2] Hernández B. Minchaca M,HCE A,et al. Measurement of heat flux in dense air-mist cooling:Part II-The influence of mist characteristics on steady-state heat transfer[J]. Experimental Thermal and Fluid Science,2013,44(1):161.
[3] HAN Yan-shen,YAN Wei,ZHANG Jiang-shan,et al. Optimization of thermal soft reduction on continuous-casting billet[J]. ISIJ International,2020,60(1):106.
[4] HAN Yan-shen,YAN Wei,ZHANG Jiang-shan,et al. Comparison and integration of final electromagnetic stirring and thermal soft reduction on continuous casting billet[J]. Journal of Iron and Steel Research,International,2021,28(2):160.
[5] 韩延申,张江山,邹雷雷,等. 喷嘴喷淋距离对连铸小方坯二冷均匀性的影响[J]. 工程科学学报,2020,42(6):739.(HAN Yan-shen,ZHANG Jiang-shan,ZOU Lei-lei,et al. Effect of nozzle spray distance on the secondary cooling uniformity of continuous casting billet[J]. Chinese Journal of Engineering,2020,42(6):739.)
[6] 邹雷雷, 黄俊雄, 李权辉,等. 连铸坯裂纹与偏析预测研究进展[J]. 连铸, 2022(2):8.(ZOU Lei-lei,HUANG Jun-xiong,LI Quan-hui,et al. Research process on the crack and segregation prediction of continuous casting strand[J]. Continuous Casting,2022(2):8.)
[7] ZHANG Ya-zhu,WEN Zhi,ZHAO Zeng-wu,et al. Velocity characteristics of air-mist jet during secondary cooling of continuous casting using PIV and LDV[J]. ISIJ International,2019,59(6):1072.
[8] Minchaca M,Castillejos E,Acosta G. Size and velocity characteristics of droplets generated by thin steel slab continuous casting secondary cooling air-mist nozzles[J]. Metallurgical and Materials Transactions B,2011,42(3):500.
[9] Kushari A. Effect of injector geometry on the performance of an internally mixed liquid atomizer[J]. Fuel Processing Technology,2010,91(11):1650.
[10] Chabicˇovsky M,Hnízdil M,Tseng A A,et al. Effects of oxide layer on Leidenfrost temperature during spray cooling of steel at high temperatures[J]. International Journal of Heat and Mass Transfer,2015,88:236.
[11] Sengupta J,Thomas B G,Wells M A. The use of water cooling during the continuous casting of steel and aluminum alloys[J]. Metallurgical and Materials Transactions A,2005,36(1):187.
[12] Raudensky M,Horsky J. Secondary cooling in continuous casting and Leidenfrost temperature effects[J]. Ironmaking and Steelmaking,2005,32(2):159.
[13] 邹雷雷,刘青,杜肖臣,等. 基于非调质钢凝固特性的二次冷却控制[J]. 工程科学学报,2022,44(3):357.(ZOU Lei-lei,LIU Qing,DU Xiao-chen,et al. Secondary cooling control based on solidification characteristics of non-quenched and tempered steel[J]. Chinese Journal of Engineering,2022,44(3):357.)
[14] 杜肖臣,刘青,张江山,等. 喷淋水量分布对C38N2钢大方坯冷却效果的影响[J]. 中国冶金,2022,32(5):93.(DU Xiao-chen,LIU Qing,ZHANG Jiang-Shan,et al. Influence of spray water distribution on cooling effect of C38 N2 bloom[J]. China Metallurgy,2022,32(5):93.)
[15] HAN Yan-shen,WANG Xing-yu,ZHANG Jiang-shan,et al. Comparison of transverse uniform and non-uniform secondary cooling strategies on heat transfer and solidification structure of continuous-casting billet[J]. Metals,2019,9(5):543.
[16] 朱定华,王慧胜,刘青,等. 连铸喷嘴冷却检测系统研发与应用[C]//2021年全国炼钢-连铸生产技术会暨连铸学术年会. 柳州:中国金属学会,2021:605.(ZHU Ding-hua,WANG Hui-sheng,LIU Qing,et al. Development and application of nozzle cooling detection system for continuous casting[C]//2021 National Steelmaking Continuous Casting Production Technology Conference and Annual Academic Conference of Continuous Casting. Liuzhou:The Chinese Society for Metals,2021:605.)
[17] SUN J,ZHANG J,LIN W,et al. Effect of impact cavity shape induced by supersonic oxygen jet on the dynamic characteristics of molten bath in converter[J]. Steel Research International,2021,92(9):2100179.
[18] 舒峰. 基于CFD的多喷嘴冲洗射流速度计算及分析[J]. 清洗世界,2020,35(12):22.(SHU Feng. Calculation and analysis of multi nozzle flushing jet velocity based on CFD[J]. The Cleaning World,2020,35(12):22.)
[19] 张亚竹. 高效连铸二冷气雾射流特征及传热研究[D].北京: 北京科技大学,2019.(ZHANG Ya-zhu. Experimental Study on the Characteristics and Heat Transfer of Air-mist Jet during Secondary Cooling of Continuous Casting[D]. Beijing:University of Science and Technology Beijing,2019.)
[20] 柴震. 连铸二冷区气液内混式喷嘴雾化特性的数值模拟及堵塞分析[D]. 马鞍山:安徽工业大学,2014.(CHAI Zhen. Numerical Simulation of Atomization Characteristics and Blockage Analysis of Internal Mixing Nozzle in CC Secondary Cooling Zone[D]. Ma'anshan:Anhui University of Technology,2014.)
[21] 林瑞泰. 沸腾换热[M]. 北京:科学出版社,1988.(LIN Rui-tai. Boiling Heat Transfer[M]. Beijing:Science Press,1988.)