生物质炭煤粉高炉混合喷吹性能分析

doi:10.13228/j.boyuan.issn0449-749x.20230309

Abstract
Figure/Table
References
Related Citation (15)

Download: PDF (0 KB) HTML (1 KB)
Export: BibTeX | EndNote (RIS)

Abstract Energy conservation and emission reduction have been elevated to the top priority for the green and sustainable growth of the iron and steel industry in light of the active promotion of the "Dual carbon" target. The application of biomass, a renewable carbon source, in blast furnace ironmaking can significantly lower the CO₂ emissions associated with iron and steel production. To improve the metallurgical properties of biomass feedstock for blast furnace injection, this paper employs pyrolytic and hydrothermal carbonization to prepare biochar, and investigates the feasibility of mixing biochar with pulverized coal for blast furnace injection. The results showed that the volatile fraction of biomass hydrochar and pyrolysis char was higher than that of bituminous coal. The fixed carbon content and higher heating value of the mixed coal would gradually decrease when the biochar was mixed with pulverized coal at a ratio of 5% to 20%, though the reduction was only slight. The blended sample is non-explosive and has an ignition point greater than 350 ℃ when the proportion of biochar is less than 20%, which satisfies the safety performance requirements of the blast furnace comminution and injection system. Better grindability and combustibility of biochar can increase the pulverizing and combustion performance of blended sample. The ash melting point of pyrolysis char blends decreases significantly more than that of hydrochar blends due to the high alkali metal content of the ash component. The increase in alkali load of pyrolysis char was substantially more than that of hydrochar when the same proportion of biochar was injected, according to calculations of the alkali load variation of the biochar blending scheme. The alkali load rose by 0.394 3 kg/t for the pyrolysis char blending scheme and 0.006 4 kg/t for the hydrochar blending scheme when the biochar ratio was 20% and the blast furnace coal injection ratio was 140 kg/t. According to the analyses presented above, biomass hydrochar can successfully meet all metallurgical performance requirements for blast furnace injection, whereas biomass pyrolysis char cannot be used to blast furnace injection due to its high content of alkali metals. The development of biomass hydrothermal carbonization technology is therefore necessary to effectively use agricultural and forestry waste biomass resources in the blast furnace ironmaking process.

Key words： biomass carbon emissions pyrolytic carbonization hydrothermal carbonization blast furnace injection

Received: 08 June 2023

	Service

	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	DAN Jiayun
	YUAN Xiang
	ZOU Fanqiu
	LI Renguo
	XU Kun
	NING Xiaojun
	WANG Guangwei

Cite this article:

DAN Jiayun,YUAN Xiang,ZOU Fanqiu等. Analysis on characteristics of blast furnace mixed injection biochar and coal[J]. Iron and Steel, 2024, 59(2): 55-64.

URL:

http://www.chinamet.cn/Jweb_gt/EN/10.13228/j.boyuan.issn0449-749x.20230309 OR http://www.chinamet.cn/Jweb_gt/EN/Y2024/V59/I2/55

[1] 赵紫薇,孔福林,童莉葛,等. 基于“3060”目标的中国钢铁行业二氧化碳减排路径与潜力分析[J]. 钢铁,2022,57(2):162.(ZHAO Z W, KONG F L, TONG L G, et.al. Analysis of CO₂ emission reduction path and potential of China's steel industry under the"3060" targe[J]. Iron and Steel, 2022, 57(2): 162.)
[2] 高建军,齐渊洪,严定鎏,等.中国低碳炼铁技术的发展路径与关键技术问题[J].中国冶金, 2021, 31 (9):64.(GAO J J, QI Y H, YAN D L, et.al. Development path and key technical problems of low carbon ironmaking in China [J]. China Metallurgy, 2021,31(9):64.)
[3] MOUSA E, WANG C, RIESBECK J, et al. Biomass applications in iron and steel industry: An overview of challenges and opportunities[J]. Renewable and sustainable energy reviews, 2016, 65: 1247.
[4] SUOPAJÄRVI H, KEMPPAINEN A, HAAPAKANGAS J, et al. Extensive review of the opportunities to use biomass-based fuels in iron and steelmaking processes[J]. Journal of Cleaner Production, 2017, 148: 709.
[5] 刘征建,王家保,张建良,等. 高炉能耗现状及降耗技术展望[J].钢铁研究学报,2023,35(1):1.(LIU Z J, WANG J B, ZHANG J L, et.al. Status of energy consumption and prospect of consumption reduction technology in blastfurnace[J]. Journal of Iron and Steel Research, 2023, 35(1): 1.)
[6] 张淑会,邵建男,兰臣臣,等. 生物质能在炼铁领域应用的研究现状及展望[J]. 钢铁,2022,57(12):13.(ZHANG S H, SHAO J N, LAN C C, et al. Application status and prospect of biomass energy in ironmaking process[J]. Iron and Steel, 2022, 57(12): 13.)
[7] 张福明,刘清梅.高炉-转炉钢铁制造流程低碳技术发展与认识[J].中国冶金,2023,33(1):1.(ZHANG F M, LIU Q M. Development and understanding on low carbon technology based on BF-BOF steel manufacturing processes[J]. China Metallurgy, 2023,33(1):1.)
[8] 魏汝飞,朱玉龙,龙红明,等. 生物质铁矿球团研究现状与展望[J].烧结球团,2022,47(1):29.(WEI R F, ZHU Y L, LONG H M, et.al. Research status and prospect of biomass iron ore pellets[J]. Sintering and Pelletizing, 2022, 47(1): 29.)
[9] 王朋,张建良,王广伟,等.热解制备芦竹半焦基础性能分析[J].中国冶金,2019,29(2):12.(WANG P, ZHANG J L, WANG G W, et.al. Analysis of basic characteristics of Arundo donax char prepared by pyrolysis[J]. China Metallurgy, 2019,29(2):12.)
[10] 周彦名,王娇月,王诗云,等. 我国生物质资源能源开发利用潜力评估[J/OL].生态学杂志:1-18[2023-08-19].http://kns.cnki.net/kcms/detail/21.1148.9.202307.12.1411.004.html.(ZHOU Y M, WANG J Y, WANG S Y, et.al. Assessment of biomass resources for energy use potential in China[J/OL]. Chinese Journal of Ecology: 1-18[2023-08-19].http://kns.cnki.net/kcms/detail/21.1148.9.202307.12.1411.004.html.)
[11] 张华,张卫国,张宗旺,等.焦炉煤气喷吹对高炉热量分布及冶炼参数的影响[J].冶金能源,2023,42(3):3.(ZHANG H,ZHANG W G,ZHANG Z W,et al. Influence of Coke Oven gas injection blast furnace heated distribution and smelting parameters[J]. Energy for Metallurgical Industry,2023,42(3):3.)
[12] 黄柱成,金芸芸,易凌云,等. 生物质热解特性及其还原铁精矿研究[J]. 烧结球团,2021,46(3):65.(HUANG Z C, JIN Y Y, YI L Y, et.al. Research on biomass pyrolysis characteristics and iron concentrate reduction[J]. Sintering and Pelletizing, 2021, 46(3): 65.)
[13] ZANDI M, MARTINEZ-PACHECO M, FRAY T A T. Biomass for iron ore sintering[J]. Minerals Engineering, 2010, 23(14): 1139.
[14] 甘敏,李浩锐,范晓慧,等. 果核生物质炭燃烧特性及其应用于烧结的减排行为[J]. 烧结球团,2022,47(1):5.(GAN M, LI H R, FAN X H, et.al. Combustion characteristics of kernel biomass char and its emission reduction behavior applied to sintering[J]. Sintering and Pelletizing, 2022, 47(1): 5.)
[15] ZHOU D, WEI R, LONG H, et al. Combustion characteristics and kinetics of different food solid wastes treatment by blast furnace[J]. Renewable Energy, 2020, 145: 530.
[16] 郑伟成, XU C C,魏汝飞,等.高炉喷吹生物炭研究进展[J].钢铁研究学报,2021,33(1):1.(ZHENG W C, XU C C, WEI R F, et al. Injection of biochar in to blast furnace:Progress and prospect[J]. Journal of Iron and Steel Research, 2021,33(1): 1.)
[17] ZHU X, LI X, XIAO L, et al. Novel carbon-rich additives preparation by degradative solvent extraction of biomass wastes for coke-making[J]. Bioresource technology, 2016, 207: 85.
[18] 龙红明,魏汝飞,李宁,等. 高炉炼铁协同处理城市可燃固废[J]. 钢铁,2018,53(3):1.(LONG H M, WEI R F, LI N, et al. Disposal of city combustible solid waste by blast furnace[J]. Iron and Steel, 2018, 53(3): 1.)
[19] 刘竹林,蒋友源,寿擎,等.高炉混合喷吹用生物质燃料可磨性及燃烧性能分析[J].中国冶金,2020,30(3):8.(LIU Z L, JIANG Y Y, SHOU Q,et.al. Analysis on grindability and combustion performance of biomass fuel for mixed injection of blast furnace[J]. China Metallurgy,2020,30(3):8.)
[20] 张华,张建良,徐润生,等.兰炭与烟煤混合燃烧特性及机制分析[J].中国冶金, 2016, 26(2): 7.(ZHANG H, ZHANG J L, XU R S,et al. Combustion characteristics and mechanism analysis of blended coal of semi coke and bituminous coal[J]. China Metallurgy, 2016, 26(2): 7.)
[21] 王臣,朱仁良,王广伟. 高炉喷吹生物质水热炭的可行性分析[J]. 钢铁,2022,57(5):22.(WANG C, ZHU R L, WANG G W, et al. Feasibility analysis of biomass hydrochar injection for blast furnace[J]. Iron and Steel, 2022, 57(5): 22.)
[22] 熊玮,王国强,周绍轩. 秸秆替代煤高炉喷吹的能源消耗及环境影响比较[J]. 环境科学与技术,2013,36(4):137.(XIONG W, WANG G Q, ZHOU S X, et al. Comparison of energy consumption and environmental impact of replacement of coal with straw injection into blast furnace[J]. Environmental Science and Technology, 2013, 36(4): 137.)
[23] 王凯迪,张建良,王广伟,等. 欧洲生物质半焦与煤混合燃烧特性分析[J]. 中国冶金,2018,28(9):12.(WANG K D, ZHANG J L, WANG G W, et al. Analysis of co-combustion characteristics of European biomass char and coal[J]. China Metallurgy, 2018, 28(9): 12.)
[24] WANG G, LI R, DAN J, et al. Preparation of biomass hydrochar and application analysis of blast furnace injection[J]. Energies, 2023, 16(3):1216.
[25] JIN L, NIU X. Micromorphology and safety properties of meager and meager-lean coal for blast furnace injection[J].International Journal of Minerals Metallurgy and Materials, 2021, 28(5): 774.
[26] 张利娜.钢铁行业低碳技术应用及发展研究[J].冶金能源,2023,42(2):3.(ZHANG L N.Application and development research of low carbon technology in iron and steel industry[J]. Energy for Metallurgical Industry,2023,42(2):3.)
[27] 赵满祥,王申洋,贾国利,等. 含钙熔剂对首钢股份喷吹煤燃烧性的影响及动力学分析[J].中国冶金,2023,33(6):81.(ZHAO M X, WANG S Y, JIA G L, et al. Effect and kinetic analysis of calcium-containing fluxon combustion property of coal injection at Shougang Co.,Ltd.[J]. China Metallurgy, 2023, 33(6): 81.)
[28] 李涛,苏步新,王广伟,等. 高炉喷吹煤粉优化选择[J].钢铁,2022,57(6):22.(LI T, SU B X, WANG G W, et al. Optimization of pulverized coal injection in to blast furnace[J]. Iron and Steel, 2022, 57(6): 22.)
[29] 李杰,宋灿阳,李小静,等. 高炉喷吹煤粉燃烧性与反应性的研究与应用[J].中国冶金,2019,29(1):8.(LI J, SONG C Y, LI X J, et al. Research and application of combustibility and reactivity of pulverized coal injected in blastfurnace[J]. China Metallurgy, 2019, 29(1): 8.)
[30] 李松阳. 碱金属对生物质燃烧过程中结渣特性影响研究[D].沈阳:沈阳航空航天大学,2017.(LI S Y. Study of the Impact of Alkali on Slagging During Biomass Combustion[D].Shengyang: Shengyang Aerospace University, 2017.)
[31] 郭豪,李燕江,胡启晨,等.高钙烟煤主要特性及高炉喷吹工艺性能综合评价[J].中国冶金, 2023, 33(10):24.(GUO H, LI Y J, HU Q C, et.al. Main characteristics of high calcium bituminous coal and comprehensive evaluation of blast furnace injection process performance[J]. China Metallurgy, 2023,33(10):24.)
[32] 黎福斌,李亚洲,夏宏蕾,等. 水热炭化废水灌溉对水稻生长及土壤理化性质的影响[J].浙江农业科学,2023,64(3):551.(LI F B, LI Y Z, XIA H L, et al. Effect of hydrothermal charred wastewater irrigation on rice growth and soil physicochemical properties[J]. Zhejiang Agricultural Science, 2023,64(3): 551.)