|
|
|
| Comparison of contribution of sub-rapid cooling and shear deformation to refinement of Fe-rich phase in hypereutectic Al–Fe alloy during rheo-extrusion |
| Xiang Wang1,2, Ren‑guo Guan1,2, Yuan‑dong Li1, Ti‑jun Chen1 |
1 State Key Laboratory of Advanced Processing and Recycling of Nonferrous Metals, Lanzhou University of Technology, Lanzhou 730050, Gansu, China
2 School of Materials Science and Engineering, Northeastern University, Shenyang 110819, Liaoning, China |
|
|
|
|
Abstract A hypereutectic Al–3Fe (wt.%) alloy was subjected by rheo-extrusion, and the effect of sub-rapid cooling and shear deformation on the refinement of Fe-rich phase was investigated. The results showed that both the primary Fe-rich phase and eutectic Fe-rich phase in the solidified Al–Fe alloy were finer than the platelike Fe-rich phase in the as-cast Al–Fe alloy with the same content of Fe. The solidified Al–Fe alloy was subjected to three stages of shear deformation, and both the primary Fe-rich phase and eutectic Fe-rich phase were fractured and the average length was refined to 400 nm, while Fe-rich phase in the as-cast Al–3Fe (wt.%) alloy was platelike and its average length was 40 μm. The tensile strength and elongation of the hypereutectic Al–3Fe (wt.%) alloy containing nanosized Fe-rich phase were 162 MPa and 25.78% while those of the as-cast Al–3Fe (wt.%) alloy containing coarse platelike Fe-rich phase were 102 MPa and 16.84%, respectively. In the refinement of Fe-rich phase in hypereutectic Al–Fe alloy during rheo-extrusion, the three stages of shear deformation contributed more than sub-rapid cooling.
|
|
Received: 09 September 2019
Published: 25 November 2020
|
|
|
|
| Cite this article: |
|
Xiang Wang,Ren‑guo Guan,Yuan‑dong Li, et al. Comparison of contribution of sub-rapid cooling and shear deformation to refinement of Fe-rich phase in hypereutectic Al–Fe alloy during rheo-extrusion[J]. Journal of Iron and Steel Research International, 2020, 27(11): 1294-1302.
|
|
|
|
| [1] |
Jian‑ming Su, Zhi‑he Dou, Ting‑an Zhang, Yan Liu. Physical simulation of bubble refinement in the bottom blowing process with mechanical agitation[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2020, 27(10): 1137-1144. |
| [2] |
Wen-tao Wang, Jiao Zhang, Feng-li Sui, Zhi-xia Zhang, Hong-yun Bi. A comparison of deformation, microstructure, mechanical properties and formability of SUS436L stainless steel in tandem and reversible cold rolling processes[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2019, 26(5): 442-451. |
| [3] |
Xiao-wei Feng, Juan Xie, Wen-ying Xue, Yong-feng Shen, Hong-bo Wang, Zhen-yu Liu. Microstructure and nanoindentation hardness of shot-peened ultrafine-grained low-alloy steel[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2019, 26(5): 472-482. |
| [4] |
Xiao-fang Shi, Li-zhong Chang, Li Zhou . Solidification structure refinement of ferritic stainless steel based on heterogeneous nucleation technology[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2019, 26(2): 137-147. |
| [5] |
Jie Sun? Cheng Sheng Ding-pu Wang ? Yun-hu Zhang Hong-gang Zhong Zhi-shuai Xu Li-juan Li Qi-jie Zhai. Influence of pulsed magneto-oscillation on microstructure and mechanical property of rectangular 65Mn steel ingot[J]. , 2018, 25(8): 862-866. |
| [6] |
Tao Liu,? Mu-jun Long, ? Deng-fu Chen, ? Hua-mei Duan, ? Lin-tao Gui, ? Sheng Yu, ? Jun-sheng Cao, ? Hua-biao Chen, ? He-lin Fan,. Effect of coarse TiN inclusions and microstructure on impact toughness fluctuation in Ti micro-alloyed steel[J]. , 2018, 25(10): 1043-1053. |
|
|
|
|
2020, Vol. 27 
