|
|
Application of steam injection in iron ore sintering: fuel combustion efficiency and CO emissions |
Yi-fan Wang1,2, Tao Yang1, Hao-yu Wang2, Long Ding1, Yun-fei Luo1, Hong-ming Long1,3 |
1 School of Metallurgical Engineering, Anhui University of Technology, Ma’anshan 243032, Anhui, China
2 Department of Chemical/Biochemical Engineering, Western University, London N6A 5B9, Ontario, Canada
3 Key Laboratory of Metallurgical Emission Reduction & Resources Recycling (Anhui University of Technology), Ministry of Education, Ma’anshan 243002, Anhui, China |
|
|
Abstract Improving the combustion efficiency of fuels is essential to reducing pollutant emissions in the iron ore sintering process. The sintering bed surface steam-injection technology has attracted significant research interest for its potential advantages in low-energy consumption and low emission. The effect of steam injection on fuel combustion efficiency and CO emission was studied by comparing the thermodynamic response from the sintering process before and after steam injection. The mechanism of improving combustion efficiency was also revealed. The results indicated that the sintering gas medium of H2O–H2–N2–O2 with the blown steam improved the heat transfer conditions of fuel combustion and promoted the water gas reaction. The optimum state of steam injection was achieved at 15 min after ignition with 0.02 m3 min-1. The CO emission reduction is 10.91% compared with the base case. The combustion efficiency was 88.83%, 6.15% higher than conventional sintering, and the solid fuel consumption was reduced by 1.15 kg t-1. It was indicated that steam injection would improve combustion efficiency and reduce solid fuel consumption. Meanwhile, the steam injection could improve the combustion kinetic conditions in the zone of unburned fuel and low oxygen partial pressure. It was conducive to the reaction of H2O with C and CO to convert the CO of reducing atmosphere to CO2, which in turn realized the complete combustion of fuel and CO and improved the efficiency of fuel combustion.
|
Received: 15 November 2021
Published: 25 January 2023
|
|
|
|
Cite this article: |
Yi-fan Wang,Tao Yang,Hao-yu Wang, et al. Application of steam injection in iron ore sintering: fuel combustion efficiency and CO emissions[J]. Journal of Iron and Steel Research International, 2023, 30(1): 31-39.
|
|
|
|
[1] |
CHEN Tong1,ZHANG Sheng1,ZHAO Liang1,FENG Junsheng2,DONG Hui1. Determination and calibration of DEM parameters for sinter particles[J]. JOURNAL OF IRON AND STEEL RESEARCH , 2023, 35(1): 24-32. |
[2] |
Yu-xiao Xue, Jian Pan, De-qing Zhu, Xin Wang, Bo-hua Li, Wei Liu. Difference of sintering performance of different types of limonitic nickel laterite[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2023, 30(1): 21-30. |
[3] |
SHAN Chang-dong, ZHANG Jian-liang, WANG Yao-zu, TANG Yong-hong, NIU Le-le, LIU Zheng-jian. Effect of high magnetite concentrates ratio on sintering index and metallurgical properties under oxygen-enriched conditions[J]. Iron and Steel, 2023, 58(1): 22-30. |
[4] |
BAO Guo-ying, LIU Lei, HAN Xiu-li, DUAN Bo-wen, QIN Li-wen. Optimization of sintering raw material blending scheme based on RDI>3.15 mm response surface methodology[J]. Iron and Steel, 2023, 58(1): 31-38. |
[5] |
ZHANG Fu-ming. Development prospects and methods on low- carbon technology in ironmaking system[J]. Iron and Steel, 2022, 57(9): 11-25. |
[6] |
XIONG Dalin1,ZHANG Gonghui2,YU Zhengwei1,CHEN Liangjun1,ZHANG Xuefeng2,LONG Hongming1. Research progress of sinter tail sectional image based on computer vision[J]. JOURNAL OF IRON AND STEEL RESEARCH , 2022, 34(9): 869-883. |
|
|
|
|