|
|
Influence of non-iso-velocity casting on flow-field index of a 41-ton six-strand Tundish by physical and numerical modeling |
Hang-hang Zhu1, Min Wang1,2, Cheng Yao1, Zhong-liang Wang1, Xiao-liang Wang3, Yan-ping Bao1 |
1 State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing, Beijing 100083, China
2 Technical Support Center for Prevention and Control of Disastrous Accidents in Metal Smelting, Beijing 100083, China
3 Fengbao Special Steel Co., Ltd., Linzhou 456552, Henan, China |
|
|
Abstract The flow-field index in a 41-ton six-strand tundish is considered through adjusting the ratio of the casting velocity between the strands to eliminate the negative impact of iso-velocity casting in multi-strand tundish on the consistency of each strand due to the large ratio of length to width with narrow shape structure, resulting in poor consistency of each strand. In particular, the response time of strand-1 and strand-6 is relatively long, which affects the uniformity of the temperature field and flow field of the entire tundish. On the basis of verifying that the error between the numerical simulations and hydraulic experiments is less than 6%, six cases with the casting velocity ratio changing from 0.8 to 1.3 (with an interval of 0.1) are considered by calculation of numerical models. It is concluded that the consistency of each flow can be obviously improved by increasing the casting velocity ratio between side-strand and middle-strand. With increasing the casting velocity ratio, the flow field in the tundish became much active, the temperature field presented well uniformity, and the tracer concentration distribution in local dead zones was improved.
|
Received: 18 November 2021
Published: 25 January 2023
|
|
|
|
Cite this article: |
Hang-hang Zhu,Min Wang,Cheng Yao, et al. Influence of non-iso-velocity casting on flow-field index of a 41-ton six-strand Tundish by physical and numerical modeling[J]. Journal of Iron and Steel Research International, 2023, 30(1): 51-63.
|
|
|
|
[1] |
MA Zhi-min, WANG Jia-hui, FANG Qing, XIAO Hong, YI Bing, ZHANG Hua. Physical simulation on optimization of baffles in an induction heating tundish[J]. CONTINUOUS CASTING, 2022, 41(4): 78-86. |
[2] |
YIN Pan, YUAN Ji-bai, LI Xiu-jie, ZHAO Hong-liang. Effects of different forms of turbulence inhibitor on tundish metallurgical[J]. CONTINUOUS CASTING, 2022, 41(3): 25-31. |
[3] |
WANG Xian-yang, HU Hao, XIE Xin, WU Chen-hui, LONG Mu-jun, CHEN Deng-fu. Flow behavior of molten steel during fewer strands casting of six-strand bloom[J]. CONTINUOUS CASTING, 2022, 41(2): 25-34. |
[4] |
WANG Jiahui1,2,3,FANG Qing1,2,3,ZHU Shuang1,2,3,LI Yang1,2,3,ZHANG Hua1,2,3. Effect of topswirling turbulence inhibitor on flow behaviors of a singlestrand slab casting tundish[J]. JOURNAL OF IRON AND STEEL RESEARCH , 2021, 33(7): 575-583. |
[5] |
YUAN Ji-bai, MA Zhi-min, YIN Pan, ZHANG Hua. Design of flow control device on 4-strand H-type double channels tundish with induction heating[J]. CONTINUOUS CASTING, 2021, 40(6): 85-90. |
[6] |
ZHANG Han, DAI Chuan-min, LEI Hong, ZHANG Xiu-xiang. Numerical simulation for flow characteristics of molten steel in tundish with channel type induction heater[J]. CONTINUOUS CASTING, 2021, 40(5): 54-59. |
|
|
|
|