|
|
|
| Mechanism of high-energy pulsed current-assisted rolling of 08AL carbon steel ultra-thin strip |
| Zhong-kai Ren1,2,3, Ya-nan Xu1,2,3, Jia-zhao Chen1,2,3, He Li1,2,3, Rui-lin Yuan1,2,3, Zhen-hua Wang1,2,3, Tao Wang1,2,3, Xiao Liu1,2,3 |
| 1 College of Mechanical and Vehicle Engineering, Taiyuan University of Technology, Taiyuan 030024, Shanxi, China 2 Engineering Research Center of Advanced Metal Composites Forming Technology and Equipment (Ministry of Education), Taiyuan University of Technology, Taiyuan 030024, Shanxi, China 3 National Key Laboratory of Metal Forming Technology and Heavy Equipment, China National Heavy Machinery Research Institute Co., Ltd., Xi’an 710016, Shaanxi, China |
|
|
|
|
Abstract To improve the plastic deformation performance of a 08AL carbon steel ultra-thin strip, a pulsed electric field was integrated into the plastic processing of the ultra-thin strip, and the effects of high-energy current on its deformation ability were investigated. Current-assisted tensile tests were employed, and the results clarified that the pulsed current could reduce the activation energy of faults and promoted dislocation slip within grains and at grain boundaries, leading to a decrease in the deformation resistance of the metal and an increase in its plastic properties. Under the current density of 2.0 A/mm2, the yield strength, tensile strength, and elongation of the rolled sample reached 425 MPa, 467 MPa, and 12.5%, respectively. During the rolling process, it was found that the pulsed current promoted the dynamic recrystallization of the ultra-thin strip, reduced its dislocation density and deformation resistance, and promoted the coordinated deformation of the metal.
|
|
|
|
|
|
| Cite this article: |
|
Zhong-kai Ren,Ya-nan Xu,Jia-zhao Chen, et al. Mechanism of high-energy pulsed current-assisted rolling of 08AL carbon steel ultra-thin strip[J]. Journal of Iron and Steel Research International, 2024, 31(02): 416-427.
|
|
|
|
| [1] |
Yi Wang, Jian Yang, Bao Wang, Hai-jun Zhang, Juan Han, Pei-yan Pei, Wen-long Lv, Jian-an Zhou. Permanent lining castable with low bulk density and thermal conductivity: bauxite castable for tundish obtained by adding pearlescent sand[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2024, 31(3): 634-646. |
| [2] |
Xian-lei Hu, Qin-cheng Xie, Yi Yuan, Ying Zhi. Microstructure and mechanical properties of Ti/Al/Ti clad plates prepared via powder-in-tube method[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2024, 31(3): 670-687. |
| [3] |
Hong-bin Dai, Jian Miao, Jia-xin Lin. Grain refinement of 5A06 aluminum alloy welds caused by tungsten inert gas welding arc characteristics under Ar–He alternating gas supply conditions: a coupled method of water-cooled copper plate test/numerical simulation[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2024, 31(3): 767-777. |
| [4] |
An-gang Ning, Yang Liu, Rui Gao, Stephen Yue, Ming-bo Wang, Han-jie Guo. Effect of Quenching Condition on Mechanical Properties, Microstructure and Precipitation Behavior of AISI H13 Steel[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2024, 31(1): 143-156. |
| [5] |
Guo-ning He, Shi-qi Wan, Bo Jiang, Chao-lei Zhang, Ya-zheng Liu, Chun-jing Wu. Adverse effect of niobium and boron on hot deformation behavior of sulfur-containing steel[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2024, 31(1): 252-263. |
| [6] |
Shi-guang Xu1, Jin-shan He1, Run-ze Zhang1, Fu-cheng Zhang2, Xi-tao Wang1,3. Static recrystallization behaviors and mechanisms of 7Mo superaustenitic stainless steel with undissolved sigma precipitates during double-stage hot deformation[J]. JOURNAL OF IRON AND STEEL RESEARCH,INTERNATIONAL, 2024, 31(02): 475-487. |
|
|
|
|
2024, Vol. 31 
