双流板坯连铸机中间包系统优化

doi:10.13228/j.boyuan.issn1005-4006.20210135

摘要
图/表
参考文献
相关文章 (15)

全文: PDF (0 KB) HTML (1 KB)
输出: BibTeX | EndNote (RIS)

摘要为了提高铸坯质量与减少中间包铸余,对中间包内腔、包盖结构、连续测温位置、非稳态拉速控制等方面优化。通过工厂生产性验证,快换中间包浇次中间包内钢水平均铸余由17.5 t降低至15.5 t、单开停浇浇次中间包内钢水平均铸余由13.5 t降低至12.5 t,连铸成坯率提高0.12%;中间包IF钢增氮不高于0.000 5%的合格率由原来76.8%提高至82.3%;夹杂缺陷封闭率和改判率降幅分别达到36%和30%。有效提高了铸坯质量,并实现连铸生产成本的降低。

	服务

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	E-mail Alert
	作者相关文章
	王志政
	钟鹏
	王欢

关键词 ：板坯连铸, 中间包, 结构优化, 连续测温, 拉速

Abstract：In order to improve the quality of billet and reduce the surplus of tundish casting, the tundish inner cavity, the structure of tundish cover, the position of continuous temperature measurement, and the control of unsteady tension speed were optimized. Through the production verification in the factory, the average molten steel residual in the tundish of quick change is reduced from 17.5 t to 15.5 t, the average molten steel residual in the tundish of single open stop is reduced from 13.5 t to 12.5 t, and the continuous casting rate is increased by 0.12%. The qualified rate of IF steel with nitrogen increasing less than 0.000 5% in tundish increased from 76.8% to 82.3%. Inclusion defect sealing rate and correction rate decreased 36% and 30%, respectively. The quality of billet is improved effectively and the cost of continuous casting is reduced.

Key words： slab continuous casting tundish structural optimization continuous temperature measurement casting speed

收稿日期: 2021-11-19

引用本文:

王志政, 钟鹏, 王欢. 双流板坯连铸机中间包系统优化[J]. 连铸, 2022, 41(3): 65-70. WANG Zhi-zheng, ZHONG Peng, WANG Huan. Optimization of tundish system for double-flow slab caster. CONTINUOUS CASTING, 2022, 41(3): 65-70.

链接本文:

http://www.chinamet.cn/Jweb_lz/CN/10.13228/j.boyuan.issn1005-4006.20210135 或 http://www.chinamet.cn/Jweb_lz/CN/Y2022/V41/I3/65

[1]	唐海燕,李京社,高锦国.中间包结构优化及冶金效果[J].钢铁钒钛,2009,30(2):40.
[2]	巩彦坤,李高良,韩继强,等.CSP钢水钙铝比对中包塞棒开口度的影响[J].河北冶金,2020(3):14.
[3]	陈希青,肖红,王璞,等.双通道感应加热中间包的三维磁流热耦合模型[J].钢铁,2021,56(6):48.
[4]	马钰,唐海燕,张硕,等.通道式感应加热五流中间包流场的水力学模拟[J].钢铁,2020,55(11):57.
[5]	朱坦华,周秋月,任英,等.二次氧化过程IF钢中间包中夹杂物演变行为[J].钢铁,2020,55(3):35.
[6]	陈玉辉,刘吉刚.中间包优化对板坯连铸钢水洁净度的影响分析[J].连铸,2019 (3):51.
[7]	王琪,赵超,李双林,等. 板坯中间包结构优化实验研究[J]. 北方钒钛,2018(3):13.
[8]	胡鹏,陈远清,张慧,等.两流板坯连铸中间包结构优化水模实验研究[J].材料与冶金学报,2011,10(2):82.
[9]	冯孔方,马建超,李建伟,等.双流板坯连铸中间包结构优化及改造[J].连铸,2021(5):83.
[10]	张硕,刘建华,苏晓峰,等.中间包微气泡冶金技术发展[J].连铸,2021(5):34.
[11]	刘志国,王洪兴.连铸保护浇注工艺改进[J].中国冶金,2013,23(8):38.
[12]	武光君,李洪建,王学新.大型连铸机中间包包盖工艺技术的开发与应用[J].连铸,2010(5):20.
[13]	霍贞蓉,元鹏飞,孙仁宝,等.中间包钢水连续测温技术分析与应用[J].连铸,2021(5):114.
[14]	钱洪俊,沙骏,李荣久,等.钢水连续测温技术[J].钢铁,1993,28(11):61.
[15]	张杰,郑淑国,朱苗勇.加热功率对感应加热中间包影响的数值模拟[J].中国冶金,2021,31(10):68.
[16]	刘涛,赵梦静,杨树峰,等.中间包等离子加热工业试验[J].中国冶金,2020,30(10):36.
[17]	王星,王国连,杨荣光,等.中间包钢水温度控制研究及优化[J].中国冶金,2018,28(1):12.
[18]	陈洋, 欧西达, 卫海瑞,等. 两流中间包控流装置优化的物理模拟与应用[J].连铸, 2019 (4):75
[19]	李丽颖,钟良才,朱英雄,等.板坯连铸中间罐结构优化及应用[J].连铸,2005(2):19.
[20]	杨克枝. 连铸中间包充氩置换影响因素分析及生产实践[J]. 连铸, 2020 (6):38.
[21]	王卫华,赵新宇,刘洋,等.连铸末期尾坯拉速的优化[J].炼钢,2017,33(2):43.
[22]	CHEN C, CHENG G G, SUN H B, et al. Optimization of weir and dam with drain holes in continuous casting slab tundish[J]. Advanced Materials Research, 2012, 476/477/478:293. .
[23]	王广辉. 一种补强型中间包包盖内衬结构:中国, CN212469744U[P]. 2021-02-05.
[24]	John Usher,Keith Ray,Jorg Uhlenbusch. Continuous measurement of liquid steel temperature in the tundish[J]. Metallurgical Industry Automation, 1998,22(4):124.
[25]	赵晶, 王臻明, 王国连,等. 400 mm特厚板坯尾坯浇铸工艺的研究[J]. 连铸, 2019 (1):4.
[26]	王卫华,赵新宇,刘洋,等.连铸末期尾坯拉速的优化[J].炼钢,2017,33(2):43.
[27]	陈素琼,蔡开科. 板坯连铸机拉速优化控制模型[J]. 钢铁, 1997(8):19.